Ford F-150 (2004-2008) :: P2106 Code - Truck Goes Into Failsafe Mode
Well my p2106 code seems to be different from all the other ones Ive read. I get the p2106 code after the truck goes into "FAILSAFE MODE" and it only goes into failsafe mode the moment the truck reaches 40mph and then loses all its power. I turn the truck off and back on and its back to normal until I go 40mph again. I scan it and only get one code p2106. The truck idles and runs perfectly until it reaches 40mph! I've replaced the entire throttle body with a new one from ford and it keeps doing the same thing. I don't want to keep buying electronic parts as they are not returnable. My truck is a 2005 Expedition with 72k miles on it
View 1 RepliesFord Super Duty (1999-2016) :: 2008 F350 Going In Limp Mode Without Engine Light - Code P0088
Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.
Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.
Ford Ranger / B-Series :: Transmission Went Into Limp Mode With O/D Light Flashing
2001 Ranger 3.0 liter has developed a transmission casualty. I was driving along at 30 mph and the transmission went into "limp' mode with O/D light flashing and truck will only barely creep along with high engine rpm. When I got the truck home I was able to retrieve a p0720, output shaft speed sensor signal fault. I had hoped that replacing the sensor would solve this casualty.
Of course this was not the case. I have read all the posts I can find for this particular fault and realize that I must electrically trace the continuity of this circuit and also ensure that it's not grounded. I have been unable to find the needed wiring diagrams or pin out information.
Before I have to try and blindly start pawing through the connectors I'm looking for the pinout for the PCM and perhaps the bulk connector above the engine between the PCM and the transmission wiring harness. I am also keen to hear of any diagnostic tips that I may have overlooked.
Sonata NF (2006-10) :: 2008 - No Reverse / Limp Mode And Code P0733
2008 sonata 3.3, no reverse however the dash indicates it's in reverse. Code P0733. I understand how an unrelated problem can cause another and wonder if I can eliminated possible problems. Car is in limp mode and stays in second or third gear.
I am about to disconnect, clean and wiggle the connectors for the transmission inner and outer sensors and then find out if I can test the sensors. That is, after I find them.
I'm also on the hunt for anything the TPS sensor might have to do with it. Battery disconnect does not work, even after hours. Is there any way something unrelated like the brake light switch or the inhibitor switch (whatever that is), might be the cause? Valve body?
Santa Fe (CM - 2007-12) :: 2008 Limp Mode - CEL / ESC And AWD Transmission Lights Blinking
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
Ford - Explorer :: 2004 V6 - Recurring Engine Failsafe Mode P2106
So my Explorer is a 2004 Eddie Bauer v-6 with about 93K miles, great condition, very clean and never had any issues. I've had it about 6yrs.
For maybe 3-4 years now the truck has seemingly randomly gone into Engine Failsafe Mode in the message center. I haven't noticed any pattern here as to when/why this occurs. The wrench icon lights up as well as the Service Engine Soon light. Sometimes I seem to notice a change in power/performance but often I don't. There are times when this happens every few days, and sometimes it goes weeks without occurring. Often it just goes out of Failsafe Mode after I've turned the truck off and restarted and seems fine again. For all of these years this has been a nuisance more than anything and so I assumed(hoped) it was just a sensor issue and nothing to be worried with.
A few days ago the truck actually shut off while driving...losing power, immediately after it kicked into Failsafe Mode while driving slowly down a straight road (no inclines or anything). Today it went into Failsafe mode, and it kept running, however the gas pedal did nothing...I couldn't accelerate at all though I still had power. Coasted to a stop. Turned truck off, started right up and the gas pedal worked fine. 15 minutes later same thing...this time when I coasted to a stop...I noticed that when I put truck in reverse I WAS able to back up using the gas pedal but couldn't go forward. Turned truck off, ran fine though still in Failsafe Mode...drove home where it sits now.
Don't really wanna drive it now though I need it as my only source of transportation. I did have the scan done on it at Autozone a month or so ago and got the P2106 "Throttle Actuator Control System--Forced Limited Power" reading...which of course means nothing to me...and the guys who worked there had no idea either. I had the oil changed at Midas yesterday where they checked fluids and all that good stuff...I mentioned it before hand and they said they looked at anything they could and couldn't find anything without running diagnostics on it...I didn't have them do this as it is quite costly and at that point I hadn't experienced the issue with losing acceleration/gas pedal functioning while driving down the road.
Lexus GX 2004-09 :: Limp Mode With Code P2445?
Got a 2006 GX throwing a P2445 code and car goes into limp mode. Is this the Air Injection Pump? Where it's located?
View 7 RepliesFord F-150 (2004-2008) :: Limp Mode - P0722 And PO713 Fault Codes
I was driving home. Problems started after pulling away from a 4-way stop. Truck started lunging almost like I was running out of fuel. Then I got a "Transmission Malfunction" in the in dash display. Followed by limp mode. I checked the Faults when I got home. I have the following:
P0720 - Powertrain - Output speed sensor Circuit
P2106 - Powertrain - Throttle Actuator Control System - Forced Limited Power (From what I understand this is associated with limp mode. Not a root of the problem)
P0713 - Powertrain - Transmission Fluid Temp Sensor Circuit High Input
P0722 - Powertrain - Output Speed Sensor Circuit No Signal
The vehicle has around 192,000 mi. Replaced cam phasers in upper engine roughly 1000 miles ago and replaced all the bearings in the rear differential roughly 100 mi ago. I haven't messed with anything on the transmission. Checked fluid level and color of transmission fluid.
Ford F-150 (2004-2008) :: Just Rebuilt Trans Now No Speedo / Truck Goes Into Limp Mode
Just fully rebuilt transmissin 4r75 replaced all planet gears clutches etc. Now with it all back together the speedo does not work on truck goes into limp mode. I replaced the vss sensor an no luck
View 8 RepliesFord Super Duty (1999-2016) :: Transmission Would Not Work In Tow Mode And Caused Engine To Go Into Limp Mode
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
Ford Super Duty (1999-2016) :: F250 Goes Into Limp Mode / OD Light Flashing / Code P1747
F250 7.3L diesel started to flash OD light, goes into limp mode, code p1747. No other codes. Have had issues for a couple of years where the truck would not shift into gear for awhile; sometimes a couple of minutes till it would engage. Have done lots of diagnostics. Visual check harness. Have 12v on pins 1&12 on harness at transmission plug. Plug had some ATF visible, but cleaned it up and continuity good. (with 4" exhaust hard to get to connector).
Checked all solenoid wires with a DVM back to plug at PCM for continuity and shorts, all good. Pulled transmission pack and checked resistance on all solenoids except temp varistor all within specs. Removed Banks Trans Command and rewired tranny plug and pulled Ottomind chip from PCM. Still goes into limp mode and throws code. Did not see any bad solder joints or burns inside PCM by the way.
Seems like PCM right? But here is a complication to my issues. For over a year I have been having electrical issues like the radio not working and windows not working intermittently after starting up. After running for awhile or on restart would work fine. Sounds like the Instrument Cluster issues or relays.(?)
Will be pulling IC and checking for any bad solder joints. However, did not throw p1747 till just recently and now my radio has really gone wonky. It comes on when key is on automatically and then proceeds to cycle through settings; AM-FM-CD.
So questions are, "Is it possible that a bad Instrument Cluster can cause a p1747 code?" "Bad Ground to Tranny" "Can a bad PCM cause a electrical issue in IC??" "Are these 2 separate issues?"
2002 f250 7.3L, 4R100 automatic trans, ~180,000miles
Banks Stinger package, 4" exhaust, TransCommand, (now removed).
Golf IV / Jetta IV :: 2002 - EPC Light Keeps Coming On / Car Goes Into Limp Mode When Reach 4000 RPM
I have a 2002 vw golf and its epc light keeps coming on and every time I reach 4000 rpm it goes into limp mode, what is the problem.
View 2 RepliesSanta FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
Ford Ranger / B-Series :: Transmission Goes Into Limp Mode When AC Turned On
Turn air conditioner on transmission goes into limp mode??
1999 ranger 2 door 2,5 engine long wheel base,,auto trans.
2wd no power windows no power seats....
Prius (2004-09) :: Main Warning / Yellow Exclamation Light And Limp Mode
My wife and I are driving our 2005 Prius with 130k miles and have experienced some weirdness with the car while driving. We've got the master warning light (red triangle w/ !), and another yellow (!) warning light, plus the center display shows a red car with an !. I've gathered that it means something possibly with the brake controller, so when I parked I put the e-brake on.
The car was driving fine with these lights on (we were in the middle of Canadian highways and couldn't stop anywhere) except that cruise control would not work.
Eventually, it actually went into limp mode, where we would floor the pedal and the car would barely accelerate. Pulled over, turned it off for a few minutes, then back on and it drove fine, warning lights still on.
I just replaced the driver's front wheel hub, and I can hear the passenger front going bad, so I'm suspicious that this may be related. Just replaced the 12v within the last few months with an Optima.
Ford Transmission :: 1993 F250 E4od Limp Mode But No Codes
Alrighty now. I have a 93 f250 idi Na.
Before problems started: the truck.shifted all 4 gears fine.
Problem(s) begins: Then out of the blue(after I shut it off... even if it was for 30sec, and then turn it on ) it would go into limp mode but if I shut it off and then turn it on again, it would work fine. After about 3weeks/ 600 miles it just went straight to limp mode.
What I did: After 3-4 weeks of that, I replaced the solenoid pack(uncooked both batteries and waited 10 min before I hooked them up) with a eBay special. After that, I had 1st,....., limp 3rd, then it'd slam like check into OD. To get second(which was limp), I'd have to manually drop it in 2 and and let off the pedal before I'd put it in D, to avoid it slamming straight into OD. It would toy with limp and OD from 35mph-45mph. Then it.just went straight to limp mode again.
What I couldn't do because don't know how to solve: I went to go get the codes read and the connector was missing and only one wire was leading to where the connector should've been.
What I did...again: I replaced the control module in the firewall. Then my codes cleared up. And same problem as when I put the new solenoid pack in. But no codes.
What is it still doing????: it's a go round battle between complete limp mode, limp mode and wanting to go into gear(suited to proper mph&rpm), or 1st, limp2&3, and OD.
What I tried: TC lock-up switch.,. And it worked but didn't solve my problem so I scratched that one.
Ford 6.0L Power Stroke Diesel :: Code For EGR Flow Restriction Cause Limp Mode?
I'm going to do a weld-in-plug delete in my RV in the next couple weeks, and its a crapshoot apparently if it'll throw a code. My immediate concern is I want to go on a trip right after, and I won't have time to fiddle about getting an SCT tuner to turn the code off. What I definitely don't want is a code for EGR flow restriction to eventually cause my motor to go into some kind of limp mode while I'm in the middle of a long drive. Is this possible?
View 14 RepliesFord F-150 (2004-2008) :: CEL On - P0172 / P01275 / P2106 Codes But Running Fine?
so i had a litle fun in the clay today ..and now my trucks check engine lights on ..i have a code reader im running a P0172 P01275 P2106 Ive cleaned the MAF and changed my air filter...still running the three codes afterwords no trouble with turning over starts right up and drives with a normal amount of power....its a 2004 5.4L V8 ...
View 12 RepliesMalibu :: Code 2135 And Also Goes Into Limp Mode
My 2010 Malibu has been throwing a code 0f 2135 also goes into limp mode. Code comes up as throttle pos sen. So looking I can see it is all built in one with the throttle body. Can it be changed with out any special tools?
View 3 Replies