Ford F-150 (2004-2008) :: 5.4 3v - Rough Idle / Stalling And Misfiring

I recently bought a 05 f150 with 5.4 3v and 195k miles needing some work. Ran great, just had a code for timing over retarded. Originally it had a cracked timing cover, so i took it off to replace and found broken guides and bad tensioners on timing. I installed new guides, chains, and tensioners, and cleaned phasers, and put back together only to find it ran terrible and had a phaser rattle. I then went in and installed phaser locks, which took care rattle but not the running issues. I can not figure it out.

ISSUES: My issues almost mirror what is said in this thread here, but this issue was never solved. [URL] ....

My issue is when started cold it starts right up, idles ok, runs ok, although a bit sluggish. Once its warm it stalls at idle, shudders when giving throttle in overdrive, and if you kick it down it will continually backfire, and slowly accelerate... it kicks down but acts like its only getting 1/8 throttle, just kind of hangs at the same rpm and slowly climbs in rpm. Sometimes it wont backfire as much, and sometimes the check engine light flashes. After it stalls at idle and you start it back up it sounds like it shudders/backfires for a split second then starts.

It is throwing many engine codes, but most are from the phaser locks. Throws code for timing over advanced on each bank (phaser locks lock them fully advanced), cam timing codes for each bank, and then a code that doesn't have to do with the timing, P2106. I am going to run some live diagnostics on it today and report back but I am fully at a loss.

View 5 Replies

Ford F-150 (2004-2008) :: 2005 - Rough Idle At 50k Miles?

2005 f-150 4.6l v8 rough idle only when truck is to normal operating temp. I have run several gas system cleaners through the truck. I replaced the air filter, the fuel filter and the spark plugs. I am only getting 14to 15 mpg mostly highway. No DTC's are showing up. The truck only has 50,000 miles.

View 6 Replies

Ford F-150 (2004-2008) :: 2005 - Intermittent Rough Idle When Engine Is Hot

I just purchased my first F150, 4.6L V8, 55,600 Miles. It intermittently has a rough idle and only seems to be when the engine is hot. I've had engine and tranny mechanics look it. The spark plugs have been inspected and are within an acceptable range. The throttle body has been cleaned. There are no trouble codes of any kind. What I can check next?

View 13 Replies

Ford F-150 (2004-2008) :: 2005 FX4 Truck Extremely Rough Idle

A week and a half ago I went out to my truck to go somewhere and I got about 2 blocks away and the truck started running really rough and had a big lack of power, so I turned around and scanned it with my code reader and the codes I got were p2271, p2196, p0303, p0012, p2197, and p2272. since then I've changed all the spark plugs, boots, swapped all the coils and injectors from a great running truck, fuel filter, and the bank 1 upstream O2 sensor.

the other thing that came to mind that could of caused the problem is that a few days before the problem started. I jump started a co-workers car and he hooked the cables up backwards on his car. Could this be the cause of the problems I'm having.

The truck is an 05 F150 FX4 5.4 with 180,000 miles on it.

View 9 Replies

Ford F-150 (2004-2008) :: 2005 5.4L Intermittent Rough Idle When Warm

I have a 05 fx4 5.4L with 85k on it. It has started idling rough when i come to a stop light or slow down to 10 mph or less. It only does it once in a while. There doesn't seem to be any real pattern. The motor shakes until you rev it up and then it goes away.

I have cleaned the maf, put in new air filter and fuel filter. And put in a new battery. Would a coil act like that? Maybe plugs? Or a vacuum leak?

View 14 Replies

Ford F-150 (2004-2008) :: 2005 - Rough Idle - Power Loss?

my f150 running right so i can enjoy it like everyone else does. I have a 2005 Ford f150 with a 5.4 auto.

It has a rough idle(shakes the truck), very little power, and poor gas mileage. Randomly It will throw a code for misfire on 1 and/or 3 on start up only. It does seem to perform better within the first few of starting but dies right off after that. In fact i got stuck in the snow the other day and it could barely break the tires loose to try and get it out (almost put in 4low cause i didn't want to hurt the trans). I have replaced:

Cats
Fuel pump
Plugs (motorcraft)
Random Coils
Did the timing chains and phasers
MAF
All new injectors
Intake gasket

Was at my mechanics and had a scanner on it and at idle the 1-4 cylinders are all show a negative cylinder contribution. But when you rev it up they all go to 0 across the board. Was kind of thinking about the Variable Timing solenoid.

View 1 Replies

Ford F-150 (2004-2008) :: 2005 - Rough Idle - Code P0012

I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....

View 1 Replies

Ford F-150 (2004-2008) :: 2005 XLT 5.4L - Rough Idle / Loss Of Power And CEL

I have a 2005 F-150XLT with the Triton 5.4L. The other day while driving on side roads (Paved, not back roads) I noticed my CEL on and it was blinking. There was a very rough idle as well as a big loss of power. When I pressed the gas pedal it was sluggish to say the least. I have yet to get a computer on it, since I had to order one. There is also a light gas smell, only smells near the rear of the truck. From what I am guessing, I think it is either a spark plur or a coil over pack, Truck has about 56K on it.

View 1 Replies

Ford F-150 (2004-2008) :: 2005 5.4 3v - Idle Rough And Knocking / Ticking In Motor

Getting these codes what they mean or need to do ..to get rid of them...p0022, p0171, p0174, p0183, p0340, p0300, p0316, p2006 did timing n plugs fuel filter n gas filter getting very bad gas mileage it runs good but here a ticking in motor at idle and more as u accelerate, running rough....

View 7 Replies

Ford F-150 (2004-2008) :: 2005 - Rough Idle At Low Speeds Primarily In Reverse / Code P0022

2005 f150 Lariat 4x4 5.4

Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.

After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.

The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.

View 3 Replies

Ford F-150 (2004-2008) :: 2005 - Idle Really Rough / Revs Will Rise And Then Drop Again If Blip The Throttle

I just locked out the cam phasers on a 2005 f150 with a 5.4. It now idles pretty rough. If I blip the throttle the revs will rise and then drop again, and it barely catches in time to prevent a stall. If I continue to tease it this way I can usually get it to stall. I'm getting no CELs or anything, but I intermittently will get a P035x code (it seemed to rove. I've gotten cylinder 1, 4, 6, but not consistently.). I have chased those around by swapping coils, checking/cleaning the connectors, etc.

I am kind of thinking that these codes are a symptom of my idle issues, and not the actual problem. What could I have done wrong? Could it be a vac issue? I had basically the entire ECU harness and all the vac lines disconnected to do the job, but as far as I can tell everything has been reconnected to the correct locations. I did have an SCT tune done to remove the phasers in the ECU. I installed it and still have the issue, so for now I am on the stock tune just to eliminate any variables.

Could my tune be the issue? Is this how you would expect the engine to behave with locked out phasers and no corresponding ECU tune?

View 1 Replies

Ford F-150 (2004-2008) :: Stalling At Idle And When Trying To Park

My 2004 fx f150 with 177K miles is stalling (rpms bottom out) driving down the road and coming to a stop (coming to idle) and when trying to park. AND, its an intermittent problem.

Of course, not spitting any codes or CEL's. I've searched the site and there are multiple types of the same issues and solutions. Narrowed it down to either the dreaded vacuum line sandwiched against firewall and engine compartment, OR the cleaning of MAF, throttle body and IAC valve.

View 12 Replies

Ford F-150 (2004-2008) :: 2005 - Stalling While Making Turns?

I've got a 4.6 in a 2005, 178000. I assume the 4.6 in an E150 would be the same as the F150.

So anyways, Started and an intermediate problem where sometimes it would stalling when making turns, such as entering a driveway, making turns or going from reverse to drive. Now its turned into more of a problem with stalling, even while in just idle and not just in gear.

At idle RPM is sporadic from 300-900. Here is where I'm at New Fuel Filter. ECM is reading 38 to 41 psi fuel pressure at idle and when the throttle is pushed.
Took a chance and changed the belt since the old was a bit lose. Even ran the engine without a belt and there was no change in my problem.
I've removed the throttle body, just learned these engines don't have an IAC, they use and IAC motor instead. I don't know how to test that but I'm googling it.

Back of throttle blade is all gunked up so I'm cleaning that now. It has no codes btw.

View 7 Replies

Ford F-150 (2004-2008) :: Knocking Noise / Running Rough And Stalling - P0340 And P0345

I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.

View 2 Replies

Stalling - Chevrolet - Trailblazer :: 2004 - Rough Idle / Engine Shuddering / Stalls Off At Stop And Low Speed

2004 Trailblazer 6cy. 2WD - has been experiencing a very rough idle, engine shudders - no matter how long it's been warmed up. Wants to stall off red lights and at very low speeds. Not throwing any lights yet - but the speedo is out ( a cam shift typical problem for this car) so I don't trust the console for lights. Worse when the heat or air is on. Rides fine with more gas/higher speeds. Definitely worse in colder temps but continues even after 40-50 mins of driving. I've heard a number of things, but can't afford to fix them all. I've heard plugs, dirty throttle camshaft, sensors, cam actuator solenoid, etc. All seem to have people who said it fixed and didn't fix the issue. Worried I'm going to stall pulling off a stop and rear end someone any day now. Where do I start!?

View 2 Replies

Ford F-150 (2004-2008) :: 2006 - Rough Idle

I have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.

I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?

I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.

View 11 Replies

Ford F-150 (2004-2008) :: Rough Idle Intermittently?

Ok, so I just replaced the entire timing set (phasers, chains, sprocket, tensioners ect) on my 2004 f150 5.4l about a month ago. I also extracted ALL 8 spark plugs and replaced those with the Champion 1 piece plugs. In addition, I replaced the intake manifold because I did this job when it was 20 degrees outside and I found a crack. Soooo, all that being said I put the whole truck back together and it runs like New. Until about a month later. When the engine gets hot, maybe after about a 30 minute drive or so, it has a really really rough idle until I give it a little bit of gas. Then it clears up. It has only done it 3 times since I put the engine back together. It might go 2 weeks and not do it. No codes. What I could be? EGR? MAS air? Only other thing I can think to say is if you get on it out on the highway, after about 3k rpms it seems like the power drops off quite a bit. Like the engine isn't getting enough fuel. I guess it could be just me, but it just doesnt seem right.. I guess I could try to unplug the MAS air flow sensor...

View 14 Replies

Ford F-150 (2004-2008) :: Rough Idle Almost Like A Misfire

I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.

No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.

View 3 Replies

Ford F-150 (2004-2008) :: Bad Vibration Or Rough Idle With AC On

I have 2008 f150 with 5.4 and 54000 miles. It has a bad vibration or rough idle only when AC is on. When AC is off it runs very smooth. Runs great while driving with AC on. Tensioner pulley was moving a lot more than normal when engine started vibrating so i replaced it and the belt but it didn't work. I also checked the other pulleys and they are good.

View 1 Replies