BMW - 328 :: Changed Front Pads / Rotors - Steering Wheel Shimmy
Have a 2009 BMW 328i with 78,000 miles. In the last year, the front brake pads and rotors have been replaced by the dealer 3 times, each time because of "warping" which is their diagnosis of a steering wheel shimmy (left to right oscillation) that occurs under light to moderate braking, especially at highway speeds.
The strange part: replacing the rotors and pads seems to solve the issue, but only for a few hundred miles.
I am led to conclude that something is causing very accelerated uneven deposition of pad material to the rotors - but what could it be? Suspension components and bushings have been inspected and check out. So do calipers. Recently completed: four wheel alignment, wheel rounding and balancing did not solve the issue. One dealer will no longer look at problem until "all four tires replaced" - but tires look fine, they are OEM RFTs with about 4/32nd's of tread left. Car seems fine cruising on highway - steering wheel shimmy only occurs under braking.
Ford F-150 (2004-2008) :: Brakes Squeaky - Rotors Bad Again?
2004 F150 XLT, 5.4, 69,000miles.
I took my truck into Brake Check because my brakes were squeaking and the rotor needed to be worked on, when I slowed down the truck would slow down smoothly....it felt like I was pressing hard then releasing etc. I knew it needed new pads etc.
Well, they replaced the Pads, and did Rotor Reface on all 4. They recommended getting the Calipers Maintenance (front 2 wheels). They wanted $800 for new rotors too (in addition). I told them no.
Fast forward around 6 months. Truck was braking great, no squeaks etc for about 4 months. Then I begin noticing huge amounts of brake dust on my wheels. Might be normal not sure.
2 months later, but truck now squeaks again while braking. And when I'm going slow, I like in a parking garage I can hear this clicking noise while I'm on the brake. CLICK.....CLICK.....CLICK....CLICK.
If you coudn't tell, I don't know much about my truck. I'm trying to learn.
Well, whenever I slow down from ~50mph, my truck vibrates like nothing I've ever seen before. My windshield wipers are bouncing around it's so bad.
I took it to a Ford Dealership to get the works done, where they rotate the tires and change the oil etc, and inspect the brakes. The guy said the rotors need to be machined.
That's not normal right? I don't drive a lot. I don't ride the brakes, I haven't had to brake hard. 6 months from the work I've had done from Brake Check, and the rotors are bad again?
I'm just going to pay Ford to fix this issue and not go back to brake check because that means I'd have to drive 3hrs. I'm curious though, shouldn't their work on the rotor still be good.....not causing them to be worked on again?! I like my truck a lot, the brakes are just pissing me off. My last truck, a 2002 ford...I had till last winter till someone rear ended my truck totaling it, I never had to do any brake work on that thing.
I got suckered into buying the extended warranty for my truck, and it says it covers the calipers.
I'm taking it into a different ford dealership that is in my town next week, and was curious if any of you had some insight on my brake situation.
Ford 6.7L Power Stroke Diesel :: Clunking In Front Brakes After Replacing Brake Pads And Turning Rotors
Ok so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 RepliesCamry :: Rotors / Pads (new) - Low Medium Squeaking Sound From Brakes
I recently had rotors and brake pads replaced on my 2007 Camry (front pads/rotors and read pads/rotors).
It was done last week and she is braking fine. But sometimes now when I brake there's a low-medium squeaking sound from the brakes. Is this normal / what's the likely cause?
Lexus LS 2007+ :: Brakes Shudder After Changing Pads And Machining Rotors
2008 LS600hl with 31K miles, been having low speed brakes shudder for quite sometime even after changing pads and machining rotors. This weekend thought about putting grease on the pins holding the pads, this did the trick, shudder is gone!
View 9 RepliesCorolla / Matrix 2009-13 :: New Brakes Rotors And Pads - Grinding Noise When Turning
I performed brake maintenance today with my brother on my 2010 corolla CE, my front rotors were warped and my pads were used ( and also uneven) and I replaced both front rotors and pads.
The install went smoothly, my brother changed a couple of brakes sets and knew what he was doing and showed me up.
Took it for a spin, the brakes work very nicely ( i bought the ceramic wagner bundle ) but theres a slight grinding noise when driving, like the pads are touching and rubbing a bit too much on the rotor, but the driving is unnafected. Also, there's a sqealing noise coming from either side when you turn only.
Braking itself produces no noise whatsoever, only when you turn that it squeals.
Sierra :: 2008 GMC - How To Remove Brake Pads And Rotors
How to remove the front brakes pads and rotors on my GMC Sierra 2008 - 1500 - crew cab - 4X4.
View 2 RepliesCivic - Honda :: 2005, Car Is Pulsing Badly After Replaced Pads And Rotors
I replaced the pads and rotors on my 05 Civic 3000 miles ago. Now it is pulsing badly again when stepping on the brakes. I can feel the pulse in the brake pedal and the steering wheel. What should I be looking for when I pull off the wheels again.
View 8 RepliesFord Super Duty (1999-2016) :: 2004 F250 - New Pads And Rotors Still A Horrible Shutter
As the title states I just finished putting pads and rotors on the front of my 04' f250. I have had a terrible shutter almost a bouncing effect while braking over the last week or so, finally got around to doing the work and still no satisfaction! My question is where to go next? Wheel bearings and tires are good, I do get a pretty good wobble/vibration in the pedal while braking. Should I be looking at a brake booster or master cylinder? Or is it possible it's a caliper? Truck goes down the road fine until and brake is applied.
View 4 RepliesFord Super Duty (1999-2016) :: 2005 - Nasty Wobble When On Brakes - Warped Rotors
Brake issues on 2005 F250. About 3 years ago during vehicle inspection the garage stated I need all for rotors on my F250. I had @40,000 miles at the time. Garage said rotors are a onetime use, no recutting them. So I got all new rotors. Prior to then I never even felt a wobble indicating they were warped. Anyhow now with 15,000 miles on them I have a huge wobble when I get on the brakes and it's 5x pronounced when pulling a trailer. I assume more warped rotors. If so, why? I pull a camper or car trailer maybe 7-10 times a year.
Now currently I am assuming its warped rotors because I have not had it "professionally" checked. I did have one occasion last August pulling the camper where I smelled the brakes being hot. The pedal got soft. After cooling it seemed ok and I flushed the old fluid and put in new. I have about 4100 miles since then and the warped feel just started about a month ago. I hate the thought of new rotors as I paid for new Ford rotors 3 years ago. Didn't want the Chinese crap from the box stores. I can't imagine how these would warp this bad after less than 15,000 miles, they are massive. Why they would so quickly?
Prius (2004-09) :: 3 Brake Dash Warning Lights Came On After Got New Brake Pads / Rotors
i have the brake (!) the ABS and the VSC lit up after i got new bearings and new brake pads and rotors, the car was also stalling before the mechanic removed these bearing "dust cover" circles that must have been causing speed sensor interfernce bc the spedometer was stuck on 0....so the car seems to be done stalling after those were removed and all the big lights went off then i hit the brakes a few miles later and those three lights came on...
View 2 RepliesFord F-150 (2009-2014) :: 2011 - Replaced Rotors But Pads Still Shaking
I've got a 2011 XLT. The front rotors have been turned twice already in 39k miles. Once at 12k and again around 24k covered under warranty. It starting having vibrations on the highway and shuddering when braking again around 36k. Tired of dealing with the OEM rotors and told it would no longer be covered under warranty I went to Autozone and got duralast rotors and pads for the front.
Swapped them out Friday
- took caliper off
- removed pads
- took caliper bracket off
- swapped rotor
- opened bleed valve to push back piston(used a vise/c clamp combo)
- closed valve with piston under pressure
- put in new pads
- placed caliper bracket back on
I did not remove the pins, they seemed to slide fine and the remaining hardware still looks fairly new.
Took it out all was good, bedded the brakes a bit and called it a night. Come out this morning and start to head out and it's shaking like crazy now once above 40 mph. Made it back this afternoon and took the passenger side off and its not making full contact with the rotors. I've read this can be common until the pads are broken in. Driver side appears fine, pads appear to be bedding fine and nothing looks out of the ordinary, I took the caliper back off but had to open the bleed valve to get it loose enough to let go of the pads.
I've even taken the passenger side back off and reset the piston again just to make sure.
Put everything back together and take it for a spin. Truck seems worse now even at slow speeds 25-50mph. Once the brakes start getting hot from stopping the shaking goes away. When the brakes start cooling back down it comes right back.
Going to swap back the OEM rotors and retest in the morning. Will take the new ones back If that puts it back to normal I may just replace with OEM ones then. The brakes work perfect it's just the shaking that I can't seem to figure out.
Anything to check? It seems like the new rotors are warped
Caravan/Voyager :: 2008 GC - Pedal Goes To Floor After Changing Brakes And Rotors
I have a 2008 GC with the E-Brake calipers in the back. I changed the brakes and rotors all around and now the petal goes to the floor. I know it has something to do with the rear brakes, because I did the fronts first and after a few pumps I had good petal.
I've done these types of rear brakes before, you use a tool to turn the caliper in. Is there anything I missed? Did I turn it in too much? I don't think it is the master cylinder because it was fine before I started and fine after I did the fronts.
Also, the e-brake doesn't hold at all now, so that's another reason I think the problem is in the rear calipers. Maybe an Adjustment? There's nothing leaking, either.
Ford Super Duty (1999-2016) :: New Rotors / Pads But Constant Squealing?
I've replaced the pads and rotors on my 97 f250 HD, only to have constant squealing. I've replaced ranger rotors before with no problem but this has been an adventure. It's squeals constantly up to 35, (I've only went up to 35) and squeals louder under braking. Just looking for some pointers. Probably just need a good cleaning. The truck is parked until its fixed more than likely.
View 6 RepliesPassat (B6) :: Front Pads And Rotors Went Shot
I've had a 2006 Passat 4Motion for about 15 Months now and it just went in for it's 20k mile service. The dealer told me that the front pads and rotors were shot, and the rear pads needed to be replaced.
I've read that the front brakes are rather easy to change but my question is: are there any aftermarket pads and/or rotors that last longer than the OEM ones? I just don't think I want to do brakes every 20k miles. Now in regards to the rear brakes, apparently my rotors are okay but my pads need to be replaced. I've read that you need the VW "Vag Com" to do that and I'm new to VW software stuff.
Passat (B5) :: 2003 - Changing Rotors And Pads
On 8/18/04 VW told me that my 03' Passat (38'000 miles) needed new rotors & pads. I bought the car new. They told me that VW used rear pads that eroded quickly and provided new rotors on the house. I decided not to press my luck and paid for new pads. I look at my pads now through the rims and it seems dangerously thin and the edge of rotors has gouge all the way around. HAS ENOUGH TIME PASSED FOR A LEGIT REPLACEMENT ON THESE PARTS?
View 4 RepliesPassat (B7) :: Rear Brake Pads And Rotors Went Shot
So my car has 36 or so thousands miles and well the rear brake pads and rotors were SHOT! The rear rotor was falling apart and huge chunks were coming off. The issue stands now that I can't spread the rear caliper for anything, the ebrake is off too. I tried to use the C-Clamp trick but it honestly didn't even budge. I also opened up the bleeder and master cylinders cap just to cross that off the list when trying to compress. This is the hardest caliper I've ever had the misfortune of dealing with and I fear that the passenger side is not going to be any better. Aside from spending more money or renting the "tool" is there anything else to check because the C-Clamp trick has work on mine and my father trucks calipers.
View 3 RepliesChrysler - Pacifica :: Shudders When Braking After New Rotors And Pads
My 2004 Pacifica (130k miles) was left parked for 2 weeks while we were away. Upon return it didn't wqnt to back out of the parking spot. After about 1/2 revolution the wheels made a clanking sound and hung up. Rolling back and forth freed things up enough to drive the car to the mechanic (about 40 miles). And after the first mile or so everything seemed to go back to normal, with no absolutely signs of anything not wanting to turn smoothly.. The mechanic thought that the problem had been that the brakes were sticking due to the car being unused and said nothing needed to be done. However, upon examination he found that we could use new front brakes and 2 motor mounts. He said that the need for brakes and motor mounts was due to normal wear and tear, and was not related to the wheels hanging up issue.
But now, immediately after installation of 2 new front rotors and pads and 2 new motor mounts there is a vibration/shudder when braking from anything more than 20-30 mph, which was never there before. The shudder is rapid and sometimes pronounced like going over the warning groves cut into the edges of pavement on the interstate. He thinks that this may be a sign that there is a driveshaft issue, and dismisses it as due to an out of round rotor since they are new. I don't know what to think. By the way, he has always been an excellent mechanic, with a great reputation and loyal following.
Ford F-150 (2004-2008) :: Rear Rotors Are Seized
I have a 04 f150 and the rear rotors are seized on and how to get them off WITHOUT destroying the rotors. i need to work on the ebrakes.
View 3 Replies