Ford F-150 - 1997-2003 :: 1999 V8 Will Not Start / Truck Started Idling Very Rough And Died
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
Ford F-150 - 1997-2003 :: Truck Died / Won't Even Try To Start
First of it's a 2003 with the 4.6. I replaced a bad alternator a couple months ago and all was fine. On the way home today the radio volume went quiet and all the dash gauges were dead. Truck died and wouldn't even try to start, no starter clicking or anything. A couple times the gauges did the "sweep" but still no start, not even a starter click. Barely even operated the hazard lights. Towed it home and hooked up the jumper cables to my 7.3 Excursion. Truck started right up and I left if hooked up for a couple minutes hoping to get enough charge in the battery to get it in the garage.
Unhooked the jumper cables, got in the truck and noticed the voltage gauge was reading nothing, tried to move it and it died. Hooked the jumper cables back up and let the Excursion charge it for about 5 minutes. Started, drove it to the garage (100ft) and backed it in. Noticed the voltage gauge was where it should be. Turned it off and back to run (didn't start) and the voltage gauge was reading good and it started right up.
Now, it doesn't appear that the battery or alternator is bad. Is there something else I should be looking at? I can take the alternator off and have it checked but don't want to go through the work if not needed to chase a ghost. Advance auto Tough One alternator BTW.
Ford F-150 - 1997-2003 :: 1999 - Died While Driving - Won't Start?
My niece has a 1999 F150 with a 4.6L engine. She was driving it down the road and it died and would not start. She called her husband, he went where she was, and when he got there, it started. She drove it home, and the next day, same thing. Died going down the road, no start, let it sit overnight, cranked like a new truck. Now it has died and will not start at all. They replaced the fuel pump. Nothing. When you turn on the key, the fuel pump runs continuously. If you pour fuel in the air filter, it will start. They checked all the fuses, nothing blown. When they try to hook it up to an OBD scanner, it does not work. No codes, nothing, it won;t pick it up.
View 9 RepliesFord F-150 - 1997-2003 :: V6 Start And Died In About 5 Seconds - IAC Buzzes
Here's what I have : 2003 F150xlt V6. about 65K miles.
Here's what happened : Drove it to the hardware store to pick up some stuff. Stopped in front of the garage. No abnormal indications during that trip at all. Decided to back to the garage and when I started it, it "ran" very rough and died in about 5 secs. Started again and chugged for about 2 or 3 secs. Tried a third time and would not run.
Here's what I've got : No CEL. all gauges indicate correctly. No anti theft blink. more than a 1/4 tank of fuel. in south central PA about at 35 degree day. parked level.
What I've checked : Wife turned the key on, I hear the fuel pump run a couple seconds with my ear in the rear wheel well. truck turns over fine. no start. turn the key off, about a two second buzz from the idle air control valve. when the key is turned on with my finger on the fuel pump relay, I feel it shift. I have pulled it and looked for corrosion. no problem. checked applicable fuses (visually).
I have tried to start with the IAC and MAF disconnected individually. tried to start it with a different key.
I have not : Banged on the tank to free up the pump. (I don't suspect it at this point)
I have not checked to see if there is fuel pressure at the fuel rail. Where is that schrader valve? I miss my books.
I have not verified that I have spark. What's the easiest way?
I have not modified my air intake in any way.
I'm headed out to a parts store tonight or walmart to get another scanner. I think my best clue here is the buzzing IAC. What's that mean?
Ford F-150 - 1997-2003 :: 1999 Truck Rumble And Died When Trying To Start
I came home from work truck was running decent got up in the morning to start it up. Tried to start up was real rumbly and died got the same twice then went to just cranking over not getting anything else tried spraying some starter fluid in air and it would try so assuming its firing abd possibly gas related ...
View 4 RepliesFord F-150 - 1997-2003 :: Low Presser AC Switch Died / Start Solenoid Just Clicks Sometimes
On my 97, just had a new engine installed. Suddenly the Lo presser AC switch died. Now the Start Solenoid (I think) just clicks sometimes. Is this Solenoid on the Firewall the Start Solenoid?
View 6 RepliesFord F-150 - 1997-2003 :: 1998 - Suddenly Died / Cranks But Won't Start - Back Link Error Code
My 4.2L died all of a sudden, it cranks but won't start. Checked the harness side to coil packs, pos. signal but no neg. Tried a code reader keeps coming back link error. Does this mean PCM is fried?
View 4 RepliesFord F-150 - 1997-2003 :: Rough Idle At Start Up
I just acquired a 2003 with 5.4 L. Did all new plugs and coils, cleaned MAF sensor, changed air filter, oil, transfluid and filter (obviously not related).
Upon start up and idle the truck has is rough, enough that it will vibrate the whole truck SLIGHTLY. Once in gear and warm, it smooths out and is fine. Unit the next stop and start.
Ford F-150 - 1997-2003 :: Little Rough On Start Up / Slight Coolant Smell
OK, I have a 1997 F150 2wd 3 door with a 4.2, approximately 130000 miles on it. I am the 2nd owner and have only had it for a couple months.
I noticed it ran a little rough on start up but smoothed out after it warmed up so I wasn't too concerned. CEL was on but it ran fine. I got the truck from my FIL and he said that it just had new hoses put on and the CEL came on after that. I noticed a slight coolant smell and after a big leak by the water pump I discovered that the guy who fixed it didn't have any of the hose clamps as tight as they should have been.
The heat went from really good to non-existent the last few weeks, never had any over heating issues though. Last week I was driving it to work and the temp gage spiked the light came on. I stopped and checked the coolant and it seemed fine. After I sat for a minute or two I checked the temp and it came back to normal. I figured it was because I let some pressure out of the system. It got hot again when I got to work but didn't spike at all driving home. I figured the water pump or t-stat was bad.
I replaced those on Saturday. When I filled the coolant up it ran rough and smoked but stopped and ran fine. Temp was fine but heat was nada. Today same thing, smokes like a steam engine for a few minutes then runs fine. Coolant smell is noticeable. I had the codes scanned and got P0303, P0174, and P0171.
I am thinking intake gaskets, since it seems to be an issue with these engines. I am going to fix it before I get a hydro lock situation, so what would be the next thing to look at before deciding that they need changed? Do I need any Ford specific tools to do this job?
Ford F-150 - 1997-2003 :: 1999 - Won't Start If So Then Rough - Fuel Pump?
Drove for 25 miles. Park, try to restart to park truck at other place. Truck start but very rough. Did drive for 20 yards and truck stop. Try to restart no way. I think I do not hear fuel pump when I turn key and gas pedal fill completely empty, no any force to move it. Should I assume fuel pump or should check some sensors first? I have P0420 for a few weeks, not source of this problem. Drove truck before with P0420 for years. No other code. Do we have PATS in keys? My truck is f250 99 LD. My pickup have PATS. How to check it?
View 5 RepliesFord F-150 - 1997-2003 :: Rough Start Then Dies - Code P0171
97 F150 4.6 Vin 6, 5-Speed Trans, 200,000mi, Rebuilt recently. I was on my way to get my truck smogged, but she threw a code, P0171. I read somewhere to clean the throttle body elbow, which I did (needed to do it anyway). After I had everything put back together, I start her, and it's rough and immediately dies. If I keep the RPM's at about 1.5k for a minute, then let off, the truck will run fine for about 30-45 seconds, then die again. I just replaced my IAC and the problem persists.
View 8 RepliesFord F-150 - 1997-2003 :: 1999 4.2L - Hot Start Rough Idle / Surges Sometimes
I am new to FTE and have a question about my 99 4.2l. After it warms up, i can shut it off and about 30 mins later try to start it again and it will idle very rough and sometimes stall. I also noticed that it surges sometimes with just off idle throttle when its cold. I am not getting any codes thrown, here's what I've done so far: cleaned the maf and throttle body, and it didnt work at all. I did convert my cht over to ect by using the plugged coolant outlet on the lower right side of the intake manifold and extending the connector wires which actually solved the problem a little bit but it still does it from time to time.
More info about the cht to ect conversion, but after reading that ford did away with them in later models i wanted to do the same while at the same time making it so much easier to swap it out if ever needed. No more getting under the truck. And where im at cht's are kind of hard to come by without having to order them Anyway, it worked flawlessly! I only had to extend the wires by about 8", wrapped them and ran it along side the injectors for a clean factory look. Ill try to post pics soon...
Ford F-150 - 1997-2003 :: Rough Idle At Start For About 30 Seconds - Cylinder 1 Misfire
2000 5.4l lariat. My cylinder 1 for 2 years has been poping p0301code and has a rough idle at start for about 30 seconds. It also has a little white smoke for that 30seconds. new cop, new spark plug, new spark plug pig tail, swapped injectors to different cylinders multiple times to change code no luck. Compression dry and wet are at 200 and all cylinders are within10%. I had a dorman intake manifold installed 4 years ago and the code came a few years after. Im thinking intake manifold gasket is bad between cylinder 1 and the heater bypass tube allowing coolant to slowly leak down into the cylinder causing my rough start. I looked through the injector hole but could not tell. With all the info I have given is there any other places or things that it could be before I do a gasket replacement or is all my tests leading to the intake manifold gasket...
View 5 RepliesFord F-150 - 1997-2003 :: 2000 - Start But Runs Rough While Stepping On Gas It Dies - Missing Gas Cap?
I have a 2000 E350 boxtruck with a 5.4 auto. The motor is a new rebuilt with about 4000 mile, coils were replaced with motor, injectors were rebuilt with motor.Today (500 miles from home) the truck died. I was going up a slight hill on an interstate. It will still start, but runs very rough and when I put it in gear and step on the gas it dies.
So I had it towed to a garage. While pushing it into the garage I noticed my gas cap was missing. I know it was on 45 min earlier because I got gas. Did I forget to put in back on? probably.. But I wondering if the missing gas cap could cause the truck to run bad,vary bad?
Ford F-150 - 1997-2003 :: 4.2L V6 Hard To Start / Occasionally Running Rough And Losing Power
I recently bought a 4.2L V6 2003 F150 with only 20,350 original miles. This car belonged to an older gent who barely used it, then passed on about 3 years ago, and truck sat around barely used by anyone. When I picked it up I ran some Seafoam through the first two gas tanks as it was occasionally running rough and losing power. Since then truck has been running incredibly smooth, but in the last few days it is getting harder to start. If I pumped it two or three times it would start OK, but today I have had to pump it while cranking it to get it to start. ( the pumping may have nothing to do with it starting)
I am replacing the fuel filter in the next couple of days, as any accumulated junk that was in the tank or lines is now probably in the filter, but it seems that a badly clogged filter would also give me some problems running, and it runs really smooth once it starts. I get a pressure gauge, (I understand the rails have a pressure test port) what pressures should I expect at what moments?
Turn key on :
Crank engine :
I am brand new to the F150 and trucks in general.
Ford Super Duty (1999-2016) :: 1997 F450 Idling Rough / Died And Would Restart But Has Zero Power
It has 100k on the clock. I bought it about 2 years ago and only put about 500 miles on it. It is only used as a farm truck. Historically it would periodically die at idle in park. Would always start up immediately and run fine. Plenty of power.
Today the truck started up and idled a few seconds and started idling rough. It died and would restart but has zero power. Put it in gear and it would die. Did this a few times now can't even get it started.
I checked all fuses. I checked the dist cap and rotor. Don't look the best but don't think this is the problem. I get the same result on both front and rear tanks. From what I have read sounds like a fuel pump or regulator. Where is the regulator located?
1997 F450 superduty 7.5 gas ...
Ford 7.3L Power Stroke (1999-2003) :: Truck Just Ran Rough And Died
So there's no signal/ electrical feed to the passenger side cylinders. I ohmd all the UVCH and they check out. Moved the wiring harness around near the big black multi pin plug under the air intake to the turbo and the passenger bank kicks in and out so it's definitely a wiring short. Need links and pics to that multi pin plug to troubleshoot the wiring.....
View 8 RepliesFord Ranger / B-Series :: 1997 Died And Won't Start
My friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Run Extremely Rough For A Couple Seconds Then Died?
Tried starting the truck, fired ran good for a couple seconds, then ran extremely rough for a couple seconds then died.
I did some research and changed the ICP because there was oil in the connector so even if it wasnt causing my issue i wanted to replace it.
Now I have the same issue but it will actually run a little longer and not stall. I thought it was fixed so i took it for a drive, after about 3 miles it bogged down and i was able to make it home with half throttle going about 30mph. Sounds almost like its running on half the cylinders. i unplugged the ICP and it continued to run that way.
I had done the 50cent mod a few years back with the peices from ford but i know the harnesses themselves can wear through so i checked the resistance between the center pin and the two pins to the right and left for both the injector harness and they had about 3ohms.
I am leaning towards an IPR but from the reading i have done it seams like most trucks will not restart after they die. I have AE so i am going to hook it up later today, just wanted some reccomendations on what to look at.
I also remember when i shut it off the unplug the ICP to see if it would clear up the needles on the gauges did a full sweep as if i disconnected the battery which i though was weird.