Ford F-150 - 1997-2003 :: P0307 Fault Code - Misfire On Cylinder 7
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 RepliesFord F-150 - 1997-2003 :: 1999 F250 Skipping After Rain - Code P0307 / Cylinder 7 Not Fire Correctly
99 F250LD 4x4 w/5.4 and 215k . I'm sure I'm not the only one with this problem. Just had quite a bit of rain in my area. I didn't drive the truck in it but 3 days after the rain stopped I did. Skipping badly ! It has done it before and will clear itself up after a heat cycle or two. This time it kicked a p0307 code. # 7 cylinder not fire correctly I believe. I got ready to replace the cop but decided to wait a day. In the mean time I pulled the connector and blue compressed air through it and the male connector.
The next morning I decided to drive it before replacing the coil. Absolutely no skipping at all. Drove at different speeds , up heels slow , high speeds, no skipping. Ran the truck for about 20 minutes or so. Is the connector getting moisture in it ? Can I fill the connector with dielectric grease? Is there another problem. I cleared the codes and am going to drive a couple of cycles to see if any come back. Like I said it has done this before but not bad enough to throw a code so I'm not sure if it's always number 7.
Ford 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesSilverado :: 2003 With Code P0307 Misfire / CEL Flashing
I'm having an issue with my 2003 Silverado, current engine is LS1 from a WS6 Trans Am, mostly stock, stainless headers, no cats, stall converter. I replaced fuel pump a few weeks ago and last week i took a road trip and when I hit the interstate the CEL started flashing. I pulled over and used my scanner and saw that it was P0307. I cleared code and continued on. The only noticeable problem was that it was not shifting into overdrive. After a while the light quit flashing and eventually it shifted into OD.
This happened several more times on a 750 mile trip. I had a mechanic friend check it over and he couldn't find anything, wasn't throwing codes at that time. He check sparked plug, swapped the coil to #5 and still had the issue. Didn't get a chance to check the fuel injector. The trip home it did the same thing. IF it were indeed a bad injector, wouldn't the problem be ongoing instead of coming and going? Took to local chevy dealer thinking they could diagnose it but since it didn't throw a code they couldn't find anything.
Ford F-150 - 1997-2003 :: Misfire On 7 Cylinder
I have changed the COP and the injector as well as the spark plug. I am still having a misfire on #7 cylinder....
View 8 RepliesFord F-150 - 1997-2003 :: Unexplained Misfire On Cylinder 1 And 5
My truck has developed a misfire on cylinders 1 and 5. The OBD2 scanner at autozone says code P0300, Po301 and P0305. I bought a new set of plugs and wires. Problem still there. I then replaced the both coils. Problem is still there. Is there a control module or something that could kill those 2 cylinders like on the older trucks with distributors?
View 7 RepliesFord F-150 - 1997-2003 :: Engine Misfire On Cylinder 4 And 6
I have 97 150 it has a misfire on cylinder 4 and 6. I put new coil packs on and new plug wires. Spark plugs are only a year old. what else it could be?
View 1 RepliesFord F-150 - 1997-2003 :: 2001 - Misfire On Cylinder 6 - CEL On?
I have an 01 5.4 Triton with engine light on I put it on the scanner and it read miss fire on cylinder 6 and 1 I changed the cops and plugs boots and spring erased the codes but the check light is back on and scanner is say miss fire on same two cylinders u can hear it in the exhaust u can smell gas when sitting at an idle around 40 MPH has a slight engine shake goes away when u accelerate I am not sure what else to do some one told me to check for vac leaks and fuel pressure.
View 14 RepliesFord F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.
Ford F-150 - 1997-2003 :: 1999 - Persistent Misfire In Cylinder 5
I have a 1999 F-150 4.2L with a misfire in #5 cylinder. I have replaced plugs, plug wires and coil pack, checked compression (147 psi) and ran 4 cans of seafoam thru it and still getting misfires on acceleration. It'a a 5 speed and it sounds rough and runs a lil rough as I go thru the first 3 gears, then it runs good as I get up to speed and cruises fine at 80mph. I'm thinking a bad fuel injector???
View 7 RepliesFord F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
Ford F-150 - 1997-2003 :: Misfire On Cylinder 8 Usually In Mornings Or If There Was Moisture In Air
I have a 2000 4.6 2wd f 150 ext cab. I started to have a misfire problem on cylinder 8 every so often usually in the mornings or if there was moisture in the air. It gradually got worse over time and when I got it read it had gone to cylinders 5,7, and 8 with the misfire codes which said misfire cylinder whichever primary/secondary circuit misfire and it has now gone to cylinder 2 as well. I replaced all the coils and the plugs with autolite platinum plugs and new coils for this motor and the problem has not changed. It came right back after I cleared the codes, what possible causes I could check out....
View 9 RepliesFord F-150 - 1997-2003 :: P0308 Cylinder 8 Misfire Detected
Where do I start? Pull the coil?
View 5 RepliesFord F-150 - 1997-2003 :: Misfire On Cylinder 3 And 8 After Putting New Trans
I've got a 1997 f150, 4.6. It sat for year and a half, trans went out and it wasn't my primary vehicle so wasn't to worried about fixing it. Until now, well got a new trans put in it, fired it up. And had a misfire, #3 and #8. Changed plugs and wires, same thing. Getting spark at the plug. So I changed both injectors, still nothing! I'm kind of stumped now.
View 4 RepliesFord F-150 - 1997-2003 :: Code PO304 - Cylinder 4 Misfire
I have a '98 F150 4X2 extended cab with a 4.2l with 233K on it. I have no problem with drivability when I drive 5 miles to work. However, a couple of weeks ago when I had to drive 15 miles to the liquor store to get what I needed (I live in a dry county) I got back into my truck, started it and drove of. It drove like crap like I lost a cylinder. Drove it back home those 15 miles, let it cool off, put my scanner on it and got a PO304 code and I think a PO174 (bank 2 lean) code. Went to the #4 cylinder and found the plug had loosened up.
Tightened it back up, cleared the codes, and went through my normal weekly routine of driving to work with no problem. Made a booze run the next weekend and the same thing happened. Limped back home and found another PO304 code. Found the plug to be tight and in good condition but changed all the plugs since they were cheap copper core and had 20K on them. The wires only have 20K on them, too. Installed platinum plugs, drove all week 5 miles to work and back just fine. Made another 15 mile run yesterday and the same crap happened all over again after I got out of the store and drove home.
Ford F-150 - 1997-2003 :: Misfire On Cylinder 3 (P0303) But Only During Towing With Ethanol
I drive a Supercrew F150 5.4L XLT 02 since 9 years, I put a Fuelflex module since 8 years, since some months I Misfire on cylinder #3 (P0303) but only during towing with Ethanol (over 2000/2500 rpm), when I drive on gas all is fine, I changed Flexfuel modul, plugs, coils, header gasket, without any positive results, it's very curious to have the problem only with ethanol (E85), I can drive very hard and at high speed with just the truck, but with a trailer as soon as I ask more power i lose one cylinder, with misfire...but like I said only on ethanol? I know engine needs more ethanol than gas, so I go check fuel pressure and maybe try to change fuel injector...
View 8 RepliesFord F-150 - 1997-2003 :: 1999 - Ride Rough - Misfire On Cylinder 3?
I'm working on my 99 f-150. I replaced all my spark plugs and coils after I got a misfire on cylinder 3 reading on the scanner. The truck was running ok but two weeks later it started to ride rough again I checked the scanner and got the same reading for a misfire on cylinder 3. Why its giving me the same misfire again? Could my injector cause that misfire? What about the egr valve?
View 8 RepliesFord F-150 - 1997-2003 :: 2001 - Codes Pops Up - Cylinder 1 Misfire?
2001 f 150 5.4 liter with it being code pops up saying cylinder one misfire, I've charge coil and spark plug ran great for awhile now starting to act up again. Got coil check and says still good and look at spark plug and looks still in good shape being just replace two weeks ago. It's running fine but if it sits over night and I get in and start it and begins to shake when I but it in drive and don't even need to move the truck just place it in drive with foot on break. I drive it awhile and it stops and runs fine?
View 9 RepliesFord F-150 - 1997-2003 :: 1998 - Cylinder 1 Misfire / Code P0301
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.