Golf/GTI VI :: 2012 / 2.5 - Shifts Too Early And Cause Some Vibration
Just got it in August, but found it shifts too early and cause some vibration. It already at 5th gear when the speed is at 45km/h.
View 11 RepliesFord F-150 - 1997-2003 :: Transmission Shifts Hard From 1st To 2nd
Have an 01 f150 super crew 4x4 with 5.4 li shifts hard from 1st to 2nd - What could be the problem?
View 1 RepliesFord F-150 - 1997-2003 :: Rebuilt Tranny Shifts Hard When Going From 2nd To 3rd And 3rd To 4th
I just had my tranny rebuilt it doesn't shift hard all the time but it does from time to time going from 2nd -3rd and 3rd -4th I thought being new it may need to soak up some fluid so the bands can swell so I ask the shop that rebuilt it that question he said they soaked them as they rebuilt it so they should be swollen already then he proceeded to tell me it was electrical is he telling me the truth because the ck engine light isn't showing any faults and if it was electric shouldn't that have been fixed in the shop while it was being rebuilt if it was interior electronic?
View 1 RepliesFord F-150 - 1997-2003 :: 1998 - RPMs Speed Up After Shifts Into Drive?
I have a 98 F150 4x4. I had some trans trouble so I pulled it out and had it rebuilt. Now when it shifts into drive the rpms speed up right before it shifts. What is causing the trans to do this? It doesn't do it all the time, only if I take off faster the usual which is most of the time.
View 1 RepliesFord F-150 - 1997-2003 :: Shifts Slow Between 1st And 2nd - Accumulator Piston And Springs?
I have a 97 f150 4x4 with the 4r70w and it shifts a bit slow between first and second. So I've been doing my research and figured id try to put new 1-2 accumulator piston and springs in. What are the part numbers so I don't order the wrong stuff.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - How To Get Better Tranny Shifts
'00 PSD w/ 291k on the clock. Starts easily, runs good, only complaint is (what I consider to be) the soft shift of the tranny. Years ago, when I bought it, it came with a Super Chips Tuner. I've never max'd it out, just usually run on the performance tow. Is there any way to clean up the shifts and make them a bit quicker with less slip. When it's time to shift, dammit, I want it to "SHIFT", not slide into gear. I don't expect it to hit the gears like a manual valve bodied drag car tranny. But, there should be something to fix this without spending a bunch of $$$..
View 4 RepliesFord F-150 - 1997-2003 :: Shifts Real Fast And Won't Downshift Once Get Going / P0122 Code
Just did some trading for a 97 f150 4x4 extended cab with a 5.4 and auto trans. The guy I got it from told me that the transmission in it shifts real fast and won't downshift once it gets going and shifts hard sometimes. From past experiences I figured it might be the tps and sure enough pulled codes and I got the 122 code for voltage to low on it. Checked the wires with my multimeter and had exactly 5.0 volts to the one wire and when I checked the ground back to the battery had 12.xx volts when i tested the signal wire it had 1.0 so all my wires checked out but I am still getting the code. I replaced the sensor once already so I guess it is possible I got a new sensor that is bad or is there a chance that maybe my plugin to it is bad?
View 13 RepliesFord F-150 - 1997-2003 :: 1998 - Transmission Will Not Go Into Drive / Shifts From Park And Goes Into Reverse
I was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 RepliesFord F-150 - 1997-2003 :: Transmission Shifts To Reverse And Drive But Park Engaged
I have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 RepliesFord F-150 - 1997-2003 :: Transmission Shifts Hard / OD Light Flashing While Driving
I have an 2003 F-150 4.6L with a 4R70W transmission, the speedometer goes crazy while I drive, the truck feels like it kicks in & out of overdrive, it shifts hard, the o/d light flashes while driving and I cannot use speed control. I have already checked the transmission fluid, changed the speed sensor, & the range sensor. After changing the range sensor the truck ran perfect for 3 days then the same problems.
View 5 RepliesFord F-150 - 1997-2003 :: Truck Shifts Excessively Hard When Going Slow Or Have To Accelerate
I am first time ford owner of a 2003 ford f150 super crew fx4 with the 5.4 Triton and lately when I accelerate hard and it down shifts. It shifts excessively hard or when your going slow and the have to accelerate it also shifts really hard i dont know if it is the diff the U-joints or if its the transmission.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 E350 - Overdrive Light Is Flashing - Shifts Hard
Here is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 RepliesFord F-150 - 1997-2003 :: 2000 4.6L - Missing Only Between 1500 And 2000 RPM
I have a 2000 F150 with 4.6l triton 125k miles. i have a bad miss ONLY between 1500 and 2000 rpm. This will happen in any gear and in neutral, but only between those rpm's. seems to happen more constant in warm weather. This miss is so bad it feels like the transmission is going to fall out. but since it does it in neutral i doubt tranny problems. things I've replaced: fuel filter, tranny fluid and filter, crankshaft pos. camshaft pos, TPI, MAF, spark plugs, Ignition coils ( all 8) cleaned throttle body ( found 1 EGR port clogged completely )..
I had a couple codes but nothing constant. Been working on this for about 1 year. Codes p0320 (ignition speed input error) p0262 (injector circuit high cylinder #1). my only question here is...... What would only make this dang engine miss between 1500 and 2000 rpm. motor runs perfect thru all other ranges. idle... high speed.. and even throttling through this bad range is ok.. but when stabilizing between 1500 and 2000 starts jerking and missing like no fuel and no fire. i have put in superchip program couple years ago and it ran fine for about 1 year, then this trouble started... I have put back to stock program but still trouble.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 Going Into Overdrive Too Early Causing It To Shake At Around 40 MPH
Its going into overdrive to early causing it to shake at around 40mph but when I get to 50mph it go away or under 35mph it not there either what could that be??? Just got torque converter and trans done and checked it wasn't that.
View 4 RepliesFord F-150 - 1997-2003 :: 2000 XL V6 4WD Went Out While Driving At 65 MPH
I have a 2000 F-150 XL with a 4.2 V-6, a 5 speed manual transmission and manual shift on the fly transfer case. The 4WD went out over a year ago. When it went out, I was driving at 65 MPH and heard what sounded like rapid relay chatter for several seconds (10 to 15 seconds) and it stopped. The sound seemed like it was coming from the dashboard area where the GEM is located, but may have been from the solenoids mounted on the engine compartment firewall. Actually could have been from both. When the 4WD tried to engage while driving at 65 MPH, the dash lights were flashing on and off and it sounded like the front differential was trying to engage. Of course I slowed down while this occurred to avoid damaging the truck should it succeeded to engage the front differential.
I have a Haynes manual but the wiring diagrams are some what ambiguous as my truck is not as common as those having ESOF. Even researching online I am not certain if the info pertains to my truck. The only diagram I found to be accurate is the vacuum control diagram. I believe I have either a wiring problem or the GEM is bad. When troubleshooting I like to isolate at the middle points to quickly eliminate one side or another when looking at a diagram/schematic.
Ford had a well-noted problem with the two solenoids that control the 4WD actuator and are mounted on the engine compartment firewall. So I started here, as this is a good halfway point and high failure area.Well, the solenoid power connectors had 12 volts on both connector pins (if I remember correctly as it was a year ago when I did some troubleshooting)regardless of transfer case shift position (2wd, 4wd high or low). I was able to manipulate the solenoids and verified they were operating, as I could feel and here the solenoids click when grounding the control side of the pin on each solenoid. I did check fuse 23 prior to checking the solenoids. Since 12 volts was present at the solenoids, it indicated power was getting to them.
So another common problem is the transfer case 4WDsensor. I removed, cleaned, and verified operation of the sensor. Reinstalled and check sensor state with transfer case in all 3 positions and it was working correctly. Also I have no 4WD indication on the dashboard when 4WD high or low is selected. Fuse 6 is good.
My main issue is not having confidence with the wiring diagrams I have found online. I am not sure if my truck has a MSOF relayor the transfer case 4WD sensor signal goes directly to the GEM.
I need to check:
1. Wiring from transfer case 4WD sensor to either GEM or MSOF relay, if there is a relay, will check it along with wiring to GEM,but don't believe it exists for my truck. (I need the wiring diagram to do this)
2. If the transfer case 4WD sensor output is getting to the GEM module, I would think the GEM module is bad. If possible, I would like to check the GEM module outputs to the solenoids, but since the GEM is buried behind the fuse panel, it probably is not feasible.
I plan to call the Ford service department in my area to determine what GEM I have and will buy a GEM online. Replacing the GEM does not look fun, so I have avoided it but wanted to be sure it was the problem.
So I want to know if I am tracking correctly and if there is anything else I should check, and would like the correct wiring diagram as indicated in item 1.
Ford F-150 - 1997-2003 :: 2000 - Heater Won't Getting Hot?
My hubby is working on a 2000 F150. The heater does not get hot. He has checked the blend door and it is functioning correctly. Is there a valve on the back of the engine that shuts the water off going to the heater core?
View 5 RepliesFord F-150 - 1997-2003 :: 2000 XLT V6 - How To Get Rear Hub Off
I am having a hell of a time getting this off. How to do it? Its a 02 f150 xlt with a 4.2 v6...
View 11 RepliesFord F-150 - 1997-2003 :: 2000 - 4x4 Will Not Work
My 2000 f150's 4x4 won't work, it has esotf, I have replaced everything I can think of, when I turn it to 4hi and 4 low i get nothing, no clicks no dash lights. I have replaced the gem, the switch, the relays, checked the fuses, i bench tested the motor it works, if i put 12v to the shift motor while on the t/c it engages to 4x4 (though I haven't driven it like that because I am not sure if its in 4hi 4 lo or in between the two) so that being said...
View 3 RepliesFord F-150 - 1997-2003 :: 2000 5.4 L - Got 4 Codes?
My scenario: 2000 F150 4x4 Supercab 5.4L 161k miles. Codes on my scan are P0113 intake air temp sensor 1 circuit high. P0102 mass air flow volume low. P0305 cyl 5 misfire. P0307 cyl 7 misfire. The 1st code I'm unfamiliar with sensor location? 2Nd code i replaced air filter, removed MAF sensor for cleaning and it appears to have only 1 heating wire or filament. Shouldn't there be 2? Plugs were changed approx 15k ago however COP's were not. Should that be my first remedy for 305&307, new plugs and coils? Also what is next sensor in line between MAF and throttle body? Is that the sensor from code P0113?
View 3 Replies