Ford F-150 - 1997-2003 :: Brakes Pedal Goes To The Floor?
I bought a 97 f150 4x4 last week. I was cleaning the frame up with a wire brush on a grinder and accidently cut one of the front brake lines. Seeing how this truck has only 100k on it and all oem stuff on it, I decided to replace the front brake components, calipers, pads, rubber and steel lines. Got it all back together and bleed the air out of the front brakes. But the pedal still goes to the floor. I can pump them up with the key off but when i turn it on the pedal goes to the floor. I did not bleed the back brakes becasue I assumed that the master cylinder would be divided and independent of each other- back and front. So it this just that the back brakes needs bled or do I have another issue like bad booster- everything was working well before I cut the line?
View 6 RepliesFord F-150 - 1997-2003 :: Brake Pedal Going To The Floor
I have a 2003 F-150 supercrew 4x4, was having problems with the brake pedal going to the floor, had replaced the front calipers, master cylinder and the brake booster. I have blead everything out including the rear calipers even though I didn`t touch them, the truck stops but the pedal isn't what it used to be, even when the truck is off the pedal has a tendency to go down, there is nothing leaking and not losing fluid, don`t know what else to do?
View 3 RepliesFord - Explorer :: 1997 - Just Crank / No Start Unless Hold The Gas Pedal To Floor
I'm working on a 1997 4.0 ohv and it has a hard start condition on first start up. any after that it will just be a crank no start condition unless you hold the gas pedal to the floor. Replaced the camshaft actuator, plenum gaskets, coolant temp sender and thermostat, fuel pressure is normal.
View 5 RepliesFord F-150 - 1997-2003 :: Brake Pedal Intermittently Goes To Floor
The brake pedal intermittently goes to the floor on my nephew's 2003 F150 without grabbing at all. Pumping the brakes restores them, then they act normally for a while. I've replaced the master cylinder with a new Motorcraft unit, no change. No ABS codes. All rubber lines are in good shape. I'm stumped, although I suspect the ABS system somehow. I'm going to have him pull the ABS fuse and see if the problem goes away.
View 6 RepliesFord F-150 - 1997-2003 :: 2002 - Brake Pedal Goes Half Way To Floor?
2002 F-150 4x4 w/ 5.4 v-8. Brake pedal goes half way to floor before it starts to stop the vehicle. I have replaced and bled the master cylinder, bled out all of the calipers, and the calipers are installed correctly because the bleeder screws are at the top on all of them so no air can be trapped up there. The truck seems to stop fine, but just takes more pedal to get it to start stopping than I'm comfortable with. Could the ABS unit need bled out too? Or could it be an adjustment issue with the booster rod?
Also, something else I noticed, and it may be related..the ABS unit usually makes a slight clanking sound (like someone kicking a metal garbage can) a couple seconds after the key is turned on. I know its the ABS unit because a couple weeks ago I had a friends scanner hooked up to the truck, and I went into the ABS computer to clear the codes (have ABS light on from what I found to be a bad sensor wire on the front drivers side according to the scanner) and as soon as i cleared the codes on the ABS, it made that sound. I don't know if maybe there is something wrong with the ABS actuator, or if it's related to the brake pedal issue.
Ford F-150 - 1997-2003 :: Brake Pedal Slowly Going To The Floor While At A Red Light
I have a 2000 SCrew KR F150. A couple of weeks ago I noticed the brake pedal was slowly going to the floor while at a red light. I pulled over and popped the hood checked the fluid reservoir. It was full, so obviously no wheel cylinder issues or fluid loss. I haven't had a chance to tear into it yet.
View 14 RepliesFord F-150 - 1997-2003 :: 2002 - Brake Pedal Fade / Started Going To Floor When Stopped
Last week my brake pedal started going to the floor when I stopped, it still stopped and felt fine on the top half of the pedal travel but then it would just slowly fade to the floor. I took it to a local shop and they said the master cylinder was leaking internally and my rear brakes were shot. I have 75,000 miles and the rear brakes were original so I told them to fix it. This is basically what I expected it to be.
They kept thinking they were getting defective master cylinders but after the two Napa parts and two Carquest parts they realized they misdiagnosed it and said I needed to take it to the dealership. I paid for the rear brake job since it needed done anyways and have an appointment for next week at the dealership. What might be causing the problem? I see no brake fluid leaks, no vacuum leaks, the booster was replaced 25,000 miles ago due to noise, no ABS light on, no CEL on, no other symptoms.
Ford 7.3L Power Stroke (1999-2003) :: Clutch Pedal Would Squeak While Coming Off The Floor?
What is failing. I have a 2000 F350 PSD with 116k miles. When I bought the truck last year, I noticed that the clutch pedal would squeak while it was coming off the floor. It doesn't happen when the engine is cold. I need to drive it about 30 min before it starts to happen. On longer trips, several hours, the squeaking is louder and the pedal gets very stiff. When I stop for fuel, I've come close to stalling when coming out of 1st gear. I can push the pedal to the floor, but on the way up, the pedal squeaks, and then once I reach a certain point, say 3-4 inches off the floor, the pedal looses all freeplay. The best way for me to describe it is the pedal travels up faster than it normally does when it's cold, and if I don't compensate with more throttle at that point, it will stall.
I've learned a lot by reading this forum for the past year, but I don't know the first thing about how to diagnose problems like this. I've taken it to 2 mechanics for test rides -- one thinks the clutch is fine and thinks the problem is the slave cylinder or a broken bushing in the pedal.
The other shop is also a small independent shop, but they specialize exclusively in Ford trucks, so I thought they would be more knowledgeable. But now I'm wondering if they could sense my ignorance and are taking advantage of the situation. They also took it for a drive, but they think the slave cylinder is fine and that the clutch needs to be replaced. I questioned him about the slave, and he pulled it to look at it, and asked me to push the pedal slowly while he was under the truck. I still had a little resistance and a faint squeak even in this situation. But he said the hydraulics are so simple that he felt we could rule that out. I can't remember exactly what he said, but I think he believes one of the springs in the clutch plate has failed. I just know they are suggesting a new clutch and they want to machine the flywheel to original specs.
I thought the leading symptom of a failing clutch was slippage under a load. So under strain, I would expect my engine to race occasionally, like I'm in neutral. But I've NEVER experienced anything remotely like this, even when driving hard in the hills pulling my travel trailer.
I know something is wrong, but based on my limited knowledge, I'm not sure what. It's getting a little harder for me to move the shifter into 1st and reverse, but once it's there it's fine. I've never experienced any racing or slippage in any gear. The one definite symptom I have is that squeaky pedal that when driven for a couple of hours, gets so stiff that it can cause near stall outs. With those symptoms, what do you think is going wrong?
Ford 7.3L Power Stroke (1999-2003) :: Brakes Lose Pressure Entirely And Pedal Goes To The Floor When Hit Bumps
The problem occurs when you hit bumps while braking, or if you get on the brakes to hard. It seems like the brakes lose pressure entirely and the pedal goes to the floor. It kicks back in when the ground smooths out, or if you are braking hard it slowly grabs again. At first i thought it was sliding, but it definitely is not. The truck appeared to be equipped with abs but the previous owner seems to have cut the abs wire/sensor at the hub. Another thought i had is maybe the brakes need to be bled and have fresh fluid put in them, I have not tried this yet (Plan to this weekend along with a dozen other things). Its rather scary when it happens. but i didnt think much of it until i nearly rear ended someone..with my younger brother in the car. Now i need to fix this asap.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Clutch Pedal Goes 1/3 Of Way Down - Drops To Floor And Stay?
I just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Pedal Slowly Go To The Floor When Hold Down Brake For Long
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 RepliesFord F-150 - 1997-2003 :: 1999 - Bed Floor Shot - Weld It?
Alright so I got ripped off on a truck that I just bought. Among all the other issues the main one is the bed. The side panels and tailgate are immaculate but the floor is shot. I read in another thread how everyone patched the holes but my issue goes much deeper. Even the bed frame is shot. Is there any way I can get a piece of steel cut to size and put new pieces for the frame and just weld it together? Id hate to have to buy a whole new bed because I am short on cash trying to start school and doing other repairs to what I thought was gonna be a perfect truck. It has the 6.5ft "Styleside" or flareside bed.
View 3 RepliesFord F-150 - 1997-2003 :: Won't Start When Hot Unless Gas Pedal Depressed
I have a 1997 f-150 V6 4.2L 2WD. I've been noticing a few symptoms going on and aren't sure if they're related or not. Firstly, I hooked my code reader to the truck and I have P0453 DTC active: Evaporative Emissions Control System Pressure Sensor High Input. As far as symptoms, truck runs overall pretty well. However, if I shut off the truck after running for awhile and then immediate attempt to start it back up, the starter will spin the flywheel but it won't ignite unless I apply pressure to the gas pedal.
Again, this is only when it's hot. I hooked up a fuel pressure gauge to the fuel rail and have 35 psi when running, and seeing as how I don't really have any other fuel-related issues going on (aside from the DTC, which I'm unfamiliar with, so it may be related??), so I don't think it's a fuel pump or anything issue. Maybe an issue with the TPS? I work on diesel trucks so throttle body systems are foreign and strange to me.
Ford F-150 - 1997-2003 :: 1999 - Cabin Water Leak - Small Puddle In Driver Side Rear Floor Corner
My 1999 F150 Supercab has developed a water leak which I would like to ask your opinions on. Parked on a 20 degree incline during a pouring rain yesterday, I came out to find a small puddle in the driver's side rear floor corner and about an ounce of water pooled in a little lip at the bottom of the rear window in the right corner of the window! Haven't started tearing anything apart yet (and might not be able to myself), but it seems that it is possibly the rear window seal as the window and the outside body area appear to be in good shape otherwise (no visible rust, no seal obviously dislocated, etc).
Also, don't know if it's related, the other day I jacked up the truck with a floor jack under the front crossmember but a bit off center which caused the truck to twist a bit before both wheels came off the ground. While doing this, I heard and felt a loud bang like something broke in the frame! Couldn't see anything out of place and something similar has happened before where a lug of the jack cup had shifted slightly while jacking the vehicle and it caused a loud bang to be heard, but this time it didn't quite feel like it was at the jack but further back.
Could something have "broken" in the truck that I can't quite see and thus this leak has occurred which wasn't there previously or could it just be coincidence that the bang and leak occurred so close in time to each other. I know it's hard to diagnose something like this without seeing the vehicle or really know what happened but I just had to put it out there as part of the events that occurred within the timeline for this leak.
Ford Ranger / B-Series :: Clutch Pedal Will Not Go To The Floor And Therefore Truck Won't Start
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
Ford Ranger / B-Series :: 2003 - Brake Pedal Goes To Floor - ABS Sensor?
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 RepliesFord - Escape :: 2003 - Brakes Unexpectedly Failed / Pedal Went Straight To The Floor
I have a 2003 Ford Escape 3.0l V-6. In June while driving to a job interview, my brakes unexpectedly failed. With absolutely no warning, the pedal went straight to the floor. I replaced the master cylinder...problem solved. 5 months later, driving to the gym, after stopping successfully several times with no mushiness in the pedal, at an intersection, the pedal goes straight to the floor...no stopping power.
I can't remember if the brake light came on last time. This time it did. Both times the fluid in the reservoir was full and looked to be relatively clean. Both times there were no apparent leaks in any of the fuel lines, abs module, at the cylinder, etc. I'm no slouch when it comes to car repair. The master cylinder replacement was done correctly, the lines were bled properly.
I have my own theories but I don't like any of them as my car rolls properly at idle, my brakes have not, nor do they currently make any noise or grinding sounds, and the pedal goes all the way to the floor.
Prius (Gen 3) :: Won't Start Unless Brake Pedal All The Way To The Floor
When I go to start and depress the brake pedal it goes all the way to the floor. The brake fluid is at the full mark and my 2011 has only 25k miles. Where should I look since it did not go all the way to the floor when I forst got it with 6K miles.
View 19 RepliesFord Super Duty (1999-2016) :: Clutch Pedal Close To Floor?
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 Replies