Ford F-150 - 1997-2003 :: 1999 - IAC Over Speed Error Code P1506
1999 F150 4.2L 125K miles.... My problems started about a month ago. I had a P1506 error. The engine was running fine but received the error code. I replaced the IAC and the air filter. Engine still running fine. A week later I received a code for the Intake Air Temp Sensor (don't remember the code). The engine still running great. I bought a new Air Temp Sensor and noticed the wires from the Air Temp Sensor were rubbing against the belt and had been severed. I made a mistake when replacing the air filter of not checking the wires (confession is good right).
The engine also constantly ran a fast idle 2000 to 2500 at this time. I repaired the wires. The engine light went off and idle now starts great and smooth but when heats up will will go to 2000-2500. I then decided to replace the Air Temp Sensor hoping to fix idle problem. Engine still idle fast when warm. However, when I come to a stop and put in neutral the engine will take a minute but go down to normal idle after sitting. Engine light stayed off for a week. Now engine light back on with original code P1506. Idle is still not working correctly.
I feel like I made it worse than it was originally and not sure what to try next.
Ford F-150 - 1997-2003 :: IAC Over Speed Error Code P1506
About 3 days ago I noticed my engine RPM was around 250 higher than usual. Usually my truck idles around 550-600 rpm (I know this is low). Anyway, yesterday it threw the P1506 "IAC over Speed Error" Code. It is idling very rough, shifting weird, but does crank up fine.
My truck is now at 93,000 miles and I just cleaned the IAC at 87,000 miles due to the common no start condition. I guess I am going to get a new IAC now since another code came up.
Well, my question is it came up with two other codes also:
P0171 - System too Lean, Bank No. 1
P0174 - System too Lean, Bank No. 2
Do you think the P1506 (IAC Code) made the O2 Sensor codes show up or is it really the O2 Sensors? I just changed my two upstream O2 Sensors around 90,000 miles. Should I get a new IAC or try to clean it again?
Ford F-150 - 1997-2003 :: Got Error Code P1000 - Idle Rough - CEL On?
What that means? The check engine light is NOT on but I looked for a code because my truck is idling rough, and when driving, when the overdrive kicks in, it vibrates really bad. As if a bad U-joint on your drive shaft. The truck has been in a field for about 5 months broke down so any clue? Haynes manual says nothing about P1000.
View 13 RepliesFord F-150 - 1997-2003 :: 1999 - Code P0500 - Speed Sensor Has Been Broken Off
So I'm getting code p0500 the question I have is will the speed sensor on the tail on my transmission cause this code on my 99 f150 4x4 . the reason I ask is because this sensor has been broken off . I'm hopeful it only control's my speedometer and is not related to the code . I've tried to remove what is left however in fear if I get it loose it may fall into the transmission. I will be replacing the speed sensor on the pumpkin this weekend . but the transmission it's the upper one is broke off below the surface of the transmission this is a manual transmission....
View 2 RepliesFord F-150 - 1997-2003 :: CEL On With Error Code P0155?
Have this code Po155 oxy sensor heated bank 2 sen 1. I have replaced all sensor in the tail pips and check engine light code still comes on.
View 7 RepliesFord F-150 - 1997-2003 :: 2002 - Got Error Code PO174
Looking for some experience/recommendations for the "what to do" and "in what order" for an error code. Recently the "SERVICE ENGINE SOON" light came on and has stayed on for the last 2 weeks. It has don this before after a heavy rain but went off after a few days but not this time. I took it to Advance Auto who hooked it up to a Trouble Code Reader and got back "PO174- Bank 2 system to lean". From what I've read from the Haynes book and other forum postings this is either a O2 sensor issue or a intake manifold gasket issue? Does this sound right? Next is how to go about addressing this issue in a systematic manner so as not "fix" 10 things that don't need fixing and not running to mechanic and paying a buttload for something I can do myself for less.
View 1 RepliesFord F-150 - 1997-2003 :: Vacuum Leak On PCV Hosing - P1131 Error Code
I'm getting the p1131 error on my 2000 xlt f150 5.4l. I know it's usually a vacuum leak on the pcv hosing, which I did have at the back and replaced as well as other softer joining sections(3 to be exact lol), but I'm still getting this error. Changed out my plugs and cops(as they needed it) and the back two plugs on both bank 1 and 2(plugs 4&8) were both white! Since this is an obvious indication of a lean burning cylinder can I make the assumption my most likely problem is dirty fuel injectors on those cylinders?
View 13 RepliesFord F-150 - 1997-2003 :: Check Engine Light Came On - Error Code P0420
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 RepliesFord F-150 (2004-2008) :: Keep Getting Error Code P0446 - Evaporative Emission Control System Vent Control
I got a Ford f150 and getting the error code P0446 Evaporative Emission Control System Vent Control. My truck has burnt up 3 of these things already in the last 8 months. Why my truck keeps killing them?
View 2 RepliesFord F-150 - 1997-2003 :: 2001 SuperCab - Airbag Error Code 2-7 Flashes On Startup
I'm getting an error code 2-7 (flashes two times, pauses, then flashes seven times) when my truck starts up. It does this cycle twice then stays on permanently. It has only started doing this since last night when I replaced my factory tape deck with a factory Cd player from a 2002 F-150.
View 14 RepliesCaravan/Voyager :: Error Code P1491 Radiator Fan Control Relay On 2003 Dodge
Vehicle: 2003 Dodge Grand Caravan 3.3 Litre
I also have my CE light on. Hooked up my reader and got the "P1491 Radiator Fan Control Relay" code. I have checked my rad fan fuse and it is okay. My attempt to locate the rad fan relay took me from the rad fan wire to a device that looks like a heat sink. It is located on the vehicle frame between the rad. and front grill. Is this the rad fan relay? If it is I'm not sure how I would replace it. It seems riveted to the frame.
Passat (B5) :: 1998 - Getting Code P1565 Idle Speed Control Throttle Position Lower Limit Not Obtained?
My 98 1.8t Passat is throwing a P1565 Idle Speed Control Throttle Position Lower Limit Not Obtained. I have cleaned the throttle body with no improvement and cleared the code many times with no luck. The car only has 114k on it car runs fine although some times will give me problems starting it ill have to sit and crank it for 40 seconds or more and also will idle on rear occasions 1300 vut normally between 850 and 900.
View 1 RepliesFord F-150 - 1997-2003 :: 1998 - Suddenly Died / Cranks But Won't Start - Back Link Error Code
My 4.2L died all of a sudden, it cranks but won't start. Checked the harness side to coil packs, pos. signal but no neg. Tried a code reader keeps coming back link error. Does this mean PCM is fried?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Code P0670 - GPCM Glow Plug Control Module Control Line Failure
How to fix SES P0670?? I understand there's a whole procedure on checking fault.
P0670:GPCM Glow plug control module control line failure. Open/grounded circuit, open/shorted GPCM, failed PCM
But how did you resolve problem? replaced GPCM, found open circuit, short --if so where?-- or replaced with updated harness.
(4C3Z-12B568-AA connector upgrade kit as in picture)???
Ford F-150 - 1997-2003 :: Relearn ECU Settings After Idle Control Valve Replaced?
When the idle control valve is replaced does the ECU have to relearn the settings?
View 2 RepliesFord F-150 - 1997-2003 :: Code PO443 / Purge Control Valve Circuit
I need the PCM pinout for a 2002 F150 4.6 For the Purge Control Valve Circuit. If possible the wire schematic would be nice also. Getting code PO443 (( hard code )) I have checked battery voltage at valve connector with key on (( 12.2 volts )) valve resistance is at be 35 ohms so I'm thinking I may have a bad wire or a bad PCM .
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Error Code P0475 - Fix?
I went and got my truck smog and it failed because of this code. I then changed the sensor cleaned out the tube and I still can't figure out how to get rid of the error code?
View 3 RepliesFord Super Duty (1999-2016) :: 2003 - Error Code From Obd Port?
So I just bought a 2003 f250 v10 and I've plugged in my code reader and it couldn't get any info, so I took it to auto zone and they got an error code. I took a test lite to each little connection on the port with the ignition on and only got power to some of the metal connections on the port. So I'm wondering if all the little connections should have power? If so where should I start to look to find the problem?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Got Error Code P1464?
Well I thought my truck was 100%, and I was going to installed a Chip. I decided to get my Forscan up and running to check and make sure.
The Buzz test Passed with no problems.
The cylinder contribution did not pass. I got error code P1464, which Forscan said that #8 failed. FYI, I turned the A/C on and the test failed. I ran it again with the A/C off and it failed again. I might have the wrong code
I then went to where you could select the gauges to view(PID's). And I saw where you could select all the cylinders injectors individually. I forgot what it was called, but all injectors were reading close to 0.0% at idle except for #8 it was reading 5.55% to 5.88%.
I am hoping this is good news, since I rather the injector be bad then a piston ring or valve. I just got the Forscan and was wondering what other test or other things I could check to narrow the problem down before removing the Valve covers. The truck runs great and there is no miss and it turns over smooth. No blowbye, just runs great. It is a 2000 F-350 dually with just over 202,000 miles