Ford F-150 - 1997-2003 :: 4.6L - High Idle At Startup
I've got a 2003 ford f-150 with a 4.6l 150000 miles. when it is started the rpms are at 2000 for about a min. and a half then it drops to normal when its started cold. when started at operating temp. The rpms are at 2000 for about 30 to 45 sec then drop to normal. The iac, upper and lower intake gaskets, intake run controller valve, dfbe, low intake and shield, coolant temp. sensor, intake air temp. sensor, egr, egr regulator valve, maf, ecm have all been swapped out no vacuum leaks all line in good condition tps voltage reading of 0.84v...
View 2 RepliesFord F-150 - 1997-2003 :: 1998 - Engine Ticking Noise Very Noticeable At Startup
I have a 98 F150 Supercab 4x4 with 4.6 and an auto trans. I have 107,000 miles on the truck. Recently developed a engine "tick". Upon start up the "tick" is very noticeable. Seems to go away after its been driven a few miles and everything comes up to operating temp. I have checked the exhaust manifolds, all studs and nuts are still there. There are no noticeable holes that I could feel in the manifolds. Read some other posts here that have the "tick under load". Mine goes away once everything warms up. What to look at or for?
View 8 RepliesFord F-150 - 1997-2003 :: 1998 V6 - High Beams And Coolant Gauge Not Working
I just bought a 98 F150 V6 Manual transmission 2wd truck. Its a clean truck and I'm liking it so far but its got a couple minor issues. Whats the point of buying a truck if you don't get to work on it??
The High Beams don't work at all. Low beams are fine. I've put new bulbs in, and fuse 16 in the passenger compartment has continuity. I'm suspecting the multiple function switch, because when I pull out to engage the high beams, nothing happens. The indicator on the dash doesn't come on, and the low beams don't turn off either.
The second issue is the coolant gauge doesn't read. When I turn the key to the on position, the needle on the gauge moves up just a bit, but it never moves after that. Anything to check?
There are a couple other minor things like the e-brake light on the dash doesn't always turn on, but I can deal with that.
Ford F-150 - 1997-2003 :: Knock At Morning Startup
1997 F150 4x4 210,000 4.6L Windsor 5 Speed. Engine totally rebuilt 15k ago (besides for timing chains and tensioners). No codes thrown.
This morning when i started my truck, it made a knocking sound (almost like metal slapping) that seemed to be coming from the bottom end of the engine. At first I thought it was a spun bearing, but then the sound went away after a minute or 2. I have Google'd the problem, and have found a few diagnoses such as: oil draining back from the filter (or something like that), or an exhaust manifold leak that stops when the metal warms up and expands, or even the starter motor not being aligned right and not disengaging properly...
This is the first time this truck has ever done this. I changed the oil and filter about 1000 miles ago with 10w-30 oil and I believe a WIX filter. Also, this is the first time using the WIX filter
The weather this morning was around 51*F, so not too cold (to me).
Also, a few weeks ago when I changed my oil, I noticed milky white stuff only on the bottom of the oil cap, and in the feed neck. The rest of my oil looked like perfect used oil. After I noticed the milky stuff, about 2-3 times a week I would clean the stuff out of the neck and off of the cap. Just recently, there hasn't been as much milky fluid. My coolant level has not changed since I marked it during the oil change. A few buddies have said it might be condensation, but it's never been like this before.
I guess my question is, is this something that could put my truck out of service if left untreated? I'm assuming it's not a spun bearing because the noise goes away, but is there a possibility coolant could be leaking into the case but stay the same level in the reservoir?
Ford F-150 - 1997-2003 :: Horn Blowing / Lights On But No Startup
I have a 97' F150, 4x4, Auto trans, 5.4L Lariat. Power locks and windows. Auto locking hubs. It doesn't appear to have any theft deterrent system installed.
It has been sitting for some time. When I hook up the battery the headlights, dash lights, and wipers turn on and the horn starts blowing continuously.
Cycling the key in the ignition or door has no effect. Cycling the key to the start position does not engage the starter.
Ford F-150 - 1997-2003 :: On Startup Ticking Noise Intermittently?
So on a cold start I keep hearing this ticking noise. Not every time, but more often than not.
I have two thoughts:
1) Low oil pressure causing timing chain tensioners to allow slack in the timing chain. Oil pressure builds up after about 1 minute of driving.
2) Oil Restricter in the valve cover starving one side of the valve cover?
Ford F-150 - 1997-2003 :: Knocking At Startup / Screech On Acceleration
I am going to start from the beginning because oftens times we don't provide all of the information that may be pertinent to the correct diagnosis or repair. It'll be kind of lengthy! It all started about 3 days ago when my wife told me that my truck was "shaking." I said, "ok, just drive the car til' I can look at it" The next morning, the I was able to look at the truck. I had a cylinder 8 misfire detected. I drove it for about 1 hour that day to and from work. I did this so I could see what what the "shaking" was. It was actually what I describe as a "shudder."
Anyways, I done a fuel pressure check and all was well. I took of the coil, tested it, it was fine. So, I took out the plug to inspect it. It was wet! Not drinched, just mildly damp. I dried it off, cleaned it off with carb cleaner and it fired right up no hesitation no nothing. No CEL light, no shaking, no shuddering. It ran perfectly normal. I let it warm up to speed and took it for a test drive around about 6 city blocks. All was well. So I took it on the highway for about a 2 mile stretch. I was givin' her some juice pretty hard to see if it would misfire. Upon acceleration I heard a screech. Now this is where it get's interesting.
The screech that I hear, I just related it to the belt because it's done it ALL the time. When I first bought the truck it squalled like a whipped puppy cause of a cheap belt. The good ol' bar of soap trick fixed that! But, ever since then, it upon shifting, or under acceleration it would screech then stop. So anyways, on the highway run, it screeched while I was accelerating. It did this from about 60mph-80mph. I then, turned around and came back home. By the time I got to the stoplight to turn off towards my house my oil light was on and the engine was knocking. Not a tap, a knock.
I slowly coasted home not going over 20mph and pulling it out of drive as much as I could. I get home, and I check the oil and there is nothing on the dipstick! WTF!? I always run Mobil1 Full synthetic and put it 6qts. It doesn't smoke, doesn't leak or nothing! So I freaked out and went and bought 2 qts of Valvoline Hi-Mi and poured it in. It brought up the hash marks and quieted the deep knock. Later that night after work, I done a full oil change and flush and put back in my Mobil1 Fully synthetic 5w20. It now knocks at startup, and smooths out to a tic. Then at idle, it sounds like a light knock. It appears that it goes away upon acceleration.
Ford F-150 - 1997-2003 :: 2002 - On Startup Exhaust Smoking?
I've got an '02 F150 with a 5.4L Triton. Despite being 10 yrs. old it's just passed the dealer warranty mileage about 80,000 miles. Due to a family situation it's been sitting idle for upwards of 2 or 3 weeks between startups.
When I do startup there's a puff of blue/geyish smoke, the engine idles rough for about 30 secs. and then everything smooths out and she runs normal.
I haven't noticed this issue before, I would add the temps here have been extremely cold the last few weeks. What direction do I point a mechanic in so he doesn't waste time or money on a diagnostic.
Ford F-150 - 1997-2003 :: Engine Pegs The Temp Gauge After Startup
97 f250 4.6l engine pegs the temp gauge after start-up. the oil pressure light comes on then after a few miles down the road anti-freeze blows out the pressure cap (15LB) then the temp goes down ,the oil light goes off and everything is normal. no its not the thermostat, i changed that and it still does it. whats up with that?
View 14 RepliesFord F-150 - 1997-2003 :: 1999 - Truck Dying Immediately Upon Startup
I've recently begun experiencing a problem with my truck dying immediately upon start up. It's a 99 5.4 and it will act like it's starting normally but then will idle down and die. If I gas it to 4000-5000 rpm it will eventually return to normal idle and run fine. At first it was once a week and then every day, usually upon the second start of the day but today it happened twice and I suspect it will become more frequent. What to check that doesn't involve a Ford Dealer?
View 3 RepliesFord F-150 - 1997-2003 :: 2000 - Engine Backfiring Through Intake At Startup
We have a 2002 F-150 4.6L 4x4. The engine went bad and we bought a new engine (remanned ATK). Had this engine installed and a year later it was bad and was determined it was a manufacturer defect so they sent a replacement engine under warranty.
We had this new engine installed. The mechanic fired it up and it backfired through the intake. They claim that the compression is good, the fuel pressure is good, and the timing is correct. Can they check these things when the truck is not running? The mechanic is completely frustrated with the situation...
Everything I read leads to a timing issue but they say they checked it so before I go in there screaming I want to make sure it couldn't possibly be anything else...
Ford F-150 - 1997-2003 :: 2001 SuperCab - Airbag Error Code 2-7 Flashes On Startup
I'm getting an error code 2-7 (flashes two times, pauses, then flashes seven times) when my truck starts up. It does this cycle twice then stays on permanently. It has only started doing this since last night when I replaced my factory tape deck with a factory Cd player from a 2002 F-150.
View 14 RepliesFord F-150 - 1997-2003 :: Engine Vibrates Severely At Startup In The Morning For A Minute Or Two During Idle
2003 F150 5.4L Tow Package 140k miles... Had coils, all plugs/wires replaced two years ago due to vibe climbing hills. Now at startup in the morning for a minute or two during idle, the engine vibrates severely then subsides and runs fine rest of day. Doesn't do this every morning. Truck lives in FL. The issue is either temperature related or moisture related. Ford service has the truck presently and attempting to diagnose from an overnight stay. They already 'fixed' the problem last week by replacing #1 plug/wire and resetting the power control module (pcm) but two days later the problem came back. Tech said today that the plugs currently installed are Bosch (any issue with these plugs?)
2003 F150 5.4L 140k miles
2011 Expy 5.4L 44k miles
Ford F-150 - 1997-2003 :: Engine Ticking Noise / Slight Clatter For 2 - 3 Seconds Upon Cold Startup
I've got a 2003 f150 with the 5.4 and 128,000 miles with an engine tick. Its not an exhaust leak I know that for sure. It has came up in the last 20,000 miles. I've used motorcraft 5 20 w/ motorcraft filter. I've tried a kreen engine treatment with no change. Heres the description/syptoms:
-Slight clatter for 2-3 seconds upon cold startup (happens very rarely)
-top end ticking that is loudest and most noticable when warm (quieter when motors cold)
-not timing chains/tensioners etc because the noise is coming from the top end and most noticeable on the passenger side.
-at idle the tick is present-when you rev at idle, the noise goes away.
-Driving (or having the engine under any load for that matter) the noise gets louder.
-Anytime I accelerate, tow/haul, go up an incline the noise gets worse
-Sounds like a "whirring" sound from within the dash.
With all that said I am thinking the lash adjusters are getting noisy. I had a certified gm tech that has 40 yrs mechanic experience under his belt and builds prostreet muscle cars on the side look at it. He listened to it to it and that was his diagnosis as well as its not that bad so just live with it. The noise at idle doesn't bother me, its when im driving with the windows down. The noise drives me crazy and is a little annoying to me.
Heres a link to a video of the sound and keep in mind it is much louder now : Triton engine noise/tick - YouTube
Ford F-150 - 1997-2003 :: 1998 - 4WD Won't Engaging?
I am having a problem with my 1998 F150 4x4. The 4WD is not engaging. It is a manual shift. I have checked the transfer case by turning the drive shaft in 2WD it is free. When I shift into 4WD it is does not spin freely. So I believe that is OK. I have checked the vaccum diaphram. It will move the piston when I attach a hose and pull vacuum on the inboard hose barb. So I believe the diaphram it self is OK. I am not sure if the hoses and selenoids are OK. They look fine. However there is a constant vacuum on the inboard hose line (red/pink color) wether I am in 4WD or not. Is this OK? How can I check the selenoids. If all this is OK, the next thing I believ it could be is the shift fork in the differential. Is that a difficult job? Do you need to pull the whole axle out to replace it?
View 14 RepliesFord F-150 - 1997-2003 :: 1998 - 4.6L Won't Rev Anymore?
Just bough a '98 F150, 4.6L; drove it home and it ran great, lots of impressive power etc... Parked it my shop and getting it ready for safety check so I can register it. All I did was change the oil, oil filter and air filter.
Couple weeks have gone by, I went to start it and it does start & idles beautiful but it will not rev. I give it gas and it's like it's choking / wants to die. The signal lights are flashing super fast which I don't recall doing before. Battery wasn't holding charge so I installed a new one tonight; no difference. Alternator is good.
I have not checked the plugs yet because I don't think that would be the cause of an overnight change from running excellent to what it is now but I will check them.
Ford F-150 - 1997-2003 :: 1998 - 4wd Won't Engage?
I have a 98 f150 4wd with manual shift on floor (msof) and the 4wd will not engage. I've done research and I've learned quite a bit but still have an issue. In All the research I've done I have learned about
View 3 RepliesFord F-150 - 1997-2003 :: 1998 - ABS Light Is On
I have a 98 f-150 4x4 the abs light is on and I can't link with scanner or seem to find anything wrong I don't have front abs just rear. I hate lights and I've checked everything I can think of.
View 5 RepliesFord F-150 - 1997-2003 :: 1998 - Misfire With No CEL?
I have a 1998 F150 4.6 that has a misfire with no CEL. I have already tried the following: checked fuel pressure, change cam shaft sensors, changed coil, checked MAf seems ok, spark plugs and wires. On my scan tool it wont show any misfires when obviously its misfiring. When driving it will run good for about 10 seconds and then misses for about 10 seconds and it just keep going in this loop.
View 8 Replies