Santa Fe (CM - 2007-12) :: 2008 - Cylinder 3 Misfire / Vehicle Is Idling Rough
I have a cylinder 3 misfire and the vehicle is idling rough so I took it to the deal because I have a power terrain warranty. They're telling me I'll need a new manifold and plenum, coil pack, plugs, and gasket. Could this be accurate? I don't want to get screwed over...
View 9 RepliesFord - Explorer :: 2003 - Misfire On Cylinder 8 / Running Rough At Idle And Under Load
126000kms on 03 explorer 4.6 truck started. Running rough at idle and under load.... Code came up for cyl 8 injector. Replaced injector... problem still there. Switched cop and plug with another cyl and plug.... same code and cycl 8 is definitely not working. Would a generic problem always affect i cylinder. I even checked wire clip on for injector... it appears ok. There is power to injector wire clip.
View 5 RepliesFocus :: Ford Idles Rough Once Engine Starts Coming Up To Temperature
We have a Ford Focus wagon that idles rough once the engine starts coming up to temperature. When you first start the car it's fine. For example, today I started the car, drove it up the road to the store and it was fine, but upon returning to my driveway just a few minutes later, as the engine temperature was just starting to come up, it started idling really rough. The idle is so rough it sounds like it's on the verge of stalling, but it never has actually stalled. An oxygen sensor has been replaced and it was good for a while, but now the problem is back. The check engine light is on as well.
View 2 RepliesFord - Explorer :: 2007 - Hard Start - Idles A Little Rough
After sitting engine cranks longer than it usually did before it starts. idles a little rough. engine light comes on after it been running about 30 sec for 1 min. after that seems to run fine.check codes po446 and p1633 always come up. if you let sit a bit with key on starts right up.replaced gas cap checked evap lines, and changed filter no luck. Did notice with lines off evap solenoid key off or on i can blow through it. that doesn't sound right.
Checked fuel pressure. key on jumps to 90psi then falls to 55psi and stays. turn off key and leaked off 10psi in 5 min.start engine while watching gauge does the same as when the key on except it falls to 30 to 35 psi and bounces between them. i think this is way low. What is the correct pressure? Shut off engine and drops to 20 in 5 min. Next I plugged line on test tee going to fuel rail and tested same results as key on. the convinced fuel pump was bad since regulator and check is there. replaced pump. problem still there.
Ford Aerostar :: 1994 Starts / Idles About 10 Seconds Then Begins To Idle Rough And Dies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
Ford - Explorer :: Motor Idles Rough Then Stalls When Turn On AC Or Defroster
When I turn-on AC or defroster, motor idles rough then stalls. My mechanic says it is not related to CHECK ENGINE light or exhaust O2 sensor? I have an 02 Ford Explorer.
View 4 RepliesBmw - X3 :: When Cold Outside Car Starts And Idles Rough Until It Gets To Temperature
The problem I have is when it is cold out under 40 degrees, my car starts rough and idles rough until it gets to temperature. My research has concluded it may be cold start. Does this sound right?
View 5 RepliesFord - Explorer :: 2006 - Misfire On Cylinder 3 And 4 Consistently
My wife's explorer has developed a misfire on cylinder 3&4 consistently. I did have cylinder 2 misfire once. But have not had it come back. The explorer is a 2006 4.6 limited with 130000 miles. Originally it was misfiring on cylinder 3. So I swapped the coil packs between 2&3. Cleared the codes. Still got a cylinder 3 misfire. So I went and bought new plugs for it. Cleared the codes. Still misfire on cylinder 3. Swapped injectors 3&1.
I took it out and romped on it and now I get cylinder 3&4 consistently misfiring. Now I got me to thinking that the only side that is misfiring is the pass side. I was going to swap o2 sensors but couldn't get the driver side out so I went and bought a new o2 upstream for the passenger side. Still get 3&4 misfire. Thought it might be fuel related so I pulled the filter. It was kinda tough to blow through so I put a new fuel filter in it. How the hell can I check the fuel pressure without a fuel fitting? I am now thinking it might be fuel pump, plugged cat, or low compression
Ford - Explorer :: 2010 - Automatic Door Locks Does Not Lock When Vehicle Starts Moving
I have a 2010 explorer. I bought it with a lot of the lights, i.e. tire pressure, skid control, abs, service engine, air bag, service rcs and some others on and these systems are not working. a module was missing associated to the AWD system, I have put one in but awd still does not work through the 4 high and 4 low work. The automatic door locks does not lock when the vehicle starts moving. Some of the lights on the dash and doors don't work either.
View 2 RepliesGolf IV / Jetta IV :: 2003 Won't Rev Over 3k - Starts / Idles Rough
I have a 2003 2.0 gas Jetta (181k miles, automatic.) that won't rev over 3k, starts rough, idles rough and wont stop setting a P0341 cam position sensor code.
The car was not running when i got it, i replaced the coil pack and it ran but not over 3k. Cleared codes, it sets the P0341 immediately.
Had timing belt, water pump, tensioner and cam pos sensor replaced. Still, sets p0341 code, starts rough, idles rough and wont rev over 3k.
The throttle servo makes a little noise when actuated, shop thinks this is my demon - suggests replace throttle body.
Prius (2004-09) :: Starts Fine But Idles A Little Rough
Just recently my Prius Taxi with 340,000+Km has developed a little problem,it starts fine but after 20-30 seconds it begins to feel like it's not running properly on all four cylinders,if i go to the exhaust pipe it seems like it's spluttering slightly.
Yesterday I changed the plugs,checked air filter and all connections,everything fine, when I accelerate it feels hesitant but after the car gets up to temp it seems to go away,it only happens when i start it first thing or if it's been left for a few hours, it's never had the throttle body cleaned and I'm wondering if what I'm describing is a symptom of this?
Buick - Regal :: Rough Idles And Misfires On Cold Starts
1991 Regal, 3800 v6.
So here's an interesting observation. When i turn the ignition to ON, I hear no sound nor feel any vibration from the fuel pump. Is there any scenario where a fuel pump fails to prime yet kicks into gear after a start? So, I've got rough idles and misfires on cold starts. Before I start replacing parts my diagnostic plans is as follows:
Remove and inspect spark plugs.
Inspect and test starter coil/distributor (still have to research how to do this)
Test resistance on fuel injectors.
Test pressure drop on fuel rails.
Test compression for possible small head leak.
I'm wondering, if I do have a tiny head leak that is letting in a drip or two of coolant after hours of the engine sitting, will I be able to see this on the gauge doing a compression test? I've never done one before and still need to buy a gauge, but maybe I'm better off just doing the other tests and if they all check out I can be certain it is a minor head leak.
My assumption is that I have a leaking injector; just trying to do things the proper way.
Ford - Explorer :: 1999 - P0303 / Cylinder 3 Misfire - Resetting Code
On my wife's '99 Explorer, she just acquired, we had a P0303, #3 cylinder misfire. I found the plug cracked and replaced it. Do the codes reset themselves or do I have to do it? I'd rather not disconnect the battery and reprogram the radio.
View 7 RepliesVolvo :: 1994 850 Turbo Wagon Starts Rough And Idles Very High
My 94 850 turbo wagon starts rough and idles very high. the rpms dont come down. After turning car off, wont restart again unless I let in sit for a while.
View 11 RepliesCamry :: 2007 V6 With Flashing Dash Lights / Rough Idles And Misfire
Having an issue with my wife's 2007 camry V6. We got the car new and the orig battery lasted over 3 years until a trip NY where the intr light was left on for a couple of days. After several tries, the battery took a jump from a tow truck and got us home. The car ran for a few days then we had starting issues as well as the dash lights would flicker and the speedo neelde would jump along with the RPM gauge. So we changed out the battery.
Now we only get about a year per battery. We also noticed the drained batteries are typically accompanied with misfiring and a bad coilpack. Not sure how that fits into the equation but we have changed 3 of the 6 coil packs. The most recent batt swap only lasted 7 months. The flickering lights and jumping RPM n Speedo needles happen last firday when my wife called me to say "its at it again" driving rough, ABS light, Ck eng light on and flashing.
She got home late and parked it in the garage. The next morning i went out to inspect and it wouldn't start. Fast clicking sound of a dead batt. I changed the battery (Costco batt fitment 24f i believe) yesterday (Monday). She called this morning and the car is still riding rough and the ck eng light is on. My guess is another coilpack.
Ford F-150 (2004-2008) :: Rough Idle Cylinder 3 Misfire
2004 Ford F150 5.4 Triton 3V Vin5.....
How this started, Drove through a lot of water as our City was in a flood on my way home and and the truck started running rough and got worse over time, I can now barely get to 40 mph as it starts to ping and sputter with no power.. the truck has been parked and not driven while in the shape it's in.
The truck keeps giving me error code P0303 Cylinder 3 misfire detected, P0174 System too lean (Bank 2) and at times another error P0300 saying multiple cylinder misfires detected.
After clearing the codes, I got new codes stating Misfire on Cylinder 2, 3, 4, 6. System too rich (Bank 1) System too lean (Bank 2)
Cleared the codes again and I'm back to Cylinder 3 misfire and System too lean (Bank 2)
What I have done so far... All repairs with in a few days...
1. Changed all spark plugs.
2. Changed all Coil Packs.
3. Changed number 3 fuel Injector.
4. Changed the Oil and Filter. (no water in the oil)
5. Changed the MAP Sensor.
6. Changed Bank 2 O2 Sensor 1 and 2.
7. Loosen the Catalytic Converter on the drivers side to re-leave back pressure thinking the Cat was plugged, still loss of power. I also drilled a small hole in the exhaust at my lowest point to see if it had water in it and it does not.
Checked for vacuum leaks using starting fluid around the intake manifold, no change in idle.. I also checked to make sure the vacuum line was still connected on the back of the intake manifold, I have found nothing leaking.
I also had cleaned the throttle body and changed the throttle position sensor.
Repairs within the last 6 months or less...
8. Replace passenger side cat.
9. Replaced both Bank 1 OS Sensors
9. Replaced Timing chains, Gears, Guides, Guide Tensioners, Oil Pump and pickup tube, Water Pump.
Cam Phasers are fine.
And number 3 coil is getting spark I changed the Ignition Coil again thinking maybe another bad pack.
Still #3 misfire and System too lean (Bank 2).
I am at a loss and not sure what to try, except for a compression test on cylinder 3 but I honestly don't think it's compression or a burnt valve.
Ford - Explorer :: 2000 - Cylinder 3 Misfire Persistently / Engine Stumbles And Has Poor Acceleration
I have a 2000 Explorer 4.0 SOHC that I'm having a persistent problem of cylinder 3 misfire. I've changed plugs with Motorcraft plugs set to the proper gap, put on new wires and have checked the resistance across the ignition module, both primary and secondary without change. I doubt that the problem could be the ignition control module as only cylinder 3 is affected. I have Auto Enginuity that I use to read the codes, attempt a repair and then clear the codes only to have P0303 appear again. Obviously the engine stumbles and has poor acceleration.
View 14 RepliesFord - Explorer :: 2000 - EGR Pipe Is Completely Broken Free From The Header - Cylinder 2 Misfire
Computer also said to replace Camshaft position sensor. The plug is getting spark and appears to be getting fuel. the plug was moist not dry. How ever i did notice the egr pipe is completely broken free from the header. Which I am replacing. Since it is reading lean on bank 2 could this alone cause more fuel to be dump in the cylinder 2 cause the plug to be too wet to fire? if not what might the possible problem be? 2000 Ford Explorer 4.0L ...
View 7 RepliesFord F-150 - 1997-2003 :: 1999 - Ride Rough - Misfire On Cylinder 3?
I'm working on my 99 f-150. I replaced all my spark plugs and coils after I got a misfire on cylinder 3 reading on the scanner. The truck was running ok but two weeks later it started to ride rough again I checked the scanner and got the same reading for a misfire on cylinder 3. Why its giving me the same misfire again? Could my injector cause that misfire? What about the egr valve?
View 8 Replies