Ford Excursion :: 2002 5.4L - Truck Start With Starting Fluid But Will Not Crank On Its Own
Having some problems with my truck.... First off I bought a 2002 excursion and drove it for one day. Then I was at the car wash cleaning up the truck. Then I saw the window fogging up so I turned the car off. Now it won't start.
I had previously installed a new stereo, but had some problems, so I ran the remote wire to the fuse box, because the wire in the harness wasn't getting power.. So after a little trouble shooting we found out that the fuel pump wasn't working or was bad.
We replaced it, now it has pressure but will not start, will start with starting fluid but will not crank on its own. someone told me it may be a bad PCM? and a dealer can only replace it... I don't have tons of cash, as i bought this truck on 8/30/12 and this happened the day after i bought it.
The previous owner has paid or the fuel pump replacing but I don't think its right on my part to have him pay more money as this may be a mess up on my part with hooking the radio up to the fuse box... we have tried the fuses,realys, crank sensors...
Ford 7.3L Power Stroke (1999-2003) :: 2000 Truck Not Starting At All
Have a 7.3 powerstroke won't start.. I have went through tons of parts check everything I can think of. I have put icp, our, fuel pump, fuel pump, injector, glow plugs and relay, fuel and air filter. new starter, new valve cover harness. HPOP is good and compression is good?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F450 Truck Not Starting
I have a 2000 F450 with a 7.3. I am having problems starting it. Batteries are good, engine turns over strong. It has started a few times after a extremely long crank (so long I am sure I am burning out the starter). I have replaced the CPS since it was cheap enough but that didn't make a difference. I have unplugged the ICP and it is very oily inside the connection. Does this mean the ICP should definitely be replaced? The truck will not start with the ICP unplugged. Should it be able to start with the ICP unplugged? Other items I plan on looking at at the IPR and possible the IDM box. Am I on the right track?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Truck Not Starting - Water In Fuel
Okay a little update on my truck not starting, and for those who have not read my earlier post. My water in fuel light has been on in my truck for probably a month of use. I drained the water sep under the truck nonstop and added several bottles of water remover and the light would not go out so I assumed the sensor was just bad. (im new to owning a powerstroke btw) I broke down coming home from work, got it towed home, and still cant get it started. It will crank fine just wont fire up. I tried unplugging the ICP, i replaced the CPS, and ordered a new water sep/ fuel filter for under the truck. And the fuel filter on top was just replaced a month before breaking down. Every single time i drain the separator tons of clear water diluted fuel comes out before it turns greenish.
Not sure if this could be a cause of getting water in my fuel but one time i filled the truck up completely and it was like the water overfilled and probably a quart or two of fuel spewed out onto the ground. Not sure where it came from. Also I have just over a quarter tank so i was thinking maybe the float broke and I just needed to add fuel but today before i went to add fuel i drained the sep and tons of water came out... Im so worried about hydrolocking my engine or ruining my injectors. But I dont know if my issue even is water related if the sensor just went bad...
Ford Excursion :: 2000 - Truck Runs Bad And Don't Shift Right
It is a 2000 excursion its got codes # 135 155 443 743 755 1747 And overdrive light is flashing really....
View 14 RepliesFord Excursion :: 2000 Truck Would Not Shift - Fuse Blown
About three weeks ago driving. My truck would not shift come to find out it was a fuse that blew. Well I pull over and replace the fuse it starts right up I get about a mile from my house and it blows again so I shut off my x and then replaced the fuse. Will not start...
Now I am getting a Pats code 1:6 and my obd2 reader says no link on my x. It used to read it all the time. I am trying to figure out what I can check to fix this problem are there any relays. Oh also my check engine light does not come on when I turn the key but my truck does crank. does this mean there is no power to my ECU. I did replace my ecu and it did not solve the issue.
Ford Excursion :: 2000 - Truck Starts To Shudder With The Cruise Control On?
I just recently bought a 2000 excursion 7.3 diesel. I'm new to diesel but learning. So far I've installed a new drop in filter in my airbox. Cut out the plastic behind the grill for cold ram air into the intake. I've done the FPR mod and cleaned out the exhaust back pressure tube. And last but not least I installed an Edge Evolution 2 programmer running stage 3 with timing advanced 2 degrees. Nothing else to the custom settings other than what stage 3 provided. Here is my problem. On the freeway at 65-75mph cruising with the cruise control on, the truck starts to shudder. I suspect my TC lockup is going out but not sure. So I wanted to test it buy installing a manual lockup switch. So I installed the switch running a wire from the plug going into the transmission on the purple with yellow wire using a saddle tap to a switch to part of the dash frame under the dash. Went to test out the switch and nothing happened.
As y'all and other forum's have described I should feel something and the od light should start flashing. I get nothing. Tried testing the switch and my ground source and everything tests out fine. Tested the saddle tap. Its fine. Tested with the switch on and using a meter to check ohms at the tap to the frame of the truck I'm getting 8ohms. I would think there shouldn't be any resistance because its a dead short but that's what I'm getting. Am I connected to the right spot on the transmission or should I move the tap to the plug under the brake master cylinder. Could my TC lockup solenoid be going out and that's what's causing the shudder and why the manual switch doesn't work.
Ford Excursion :: 2000 V10 Won't Start / Truck Will Not Even Crank / Relay Will Continue Clicking
2000 excursion V-10. I parked the truck, went back to start it and all my gauges blink, and the number one relay under the dash (interior light relay) begins clicking. The truck will not even crank. The relay will continue clicking (even with the key off) until you remove and replace the relay. Sometimes I will get absolutely nothing when I turn the key. I have tried jumping the battery, no change. Also tried starting it in neutral to trouble shoot the NSS, but it won't even click when in neutral. I checked battery connection, and followed the battery cables to look for a short but found nothing.
View 3 RepliesFord Excursion :: EGR Marbles - Truck Loses Pretty Much All Power Below 2000 RPM / Smokes And Stinks Bad
EGR marbles -- the chunks of carbon that come loose from the EGR cooler / intake manifold and stick the EGR valve open?
I've been getting these on 3 recent occasions, maybe 100 miles or so apart. The truck loses pretty much all power below 2000 rpm, smokes and stinks bad until I pull the EGR valve and dump these out. I'm trying to decide if I need to dig in and do a new EGR cooler and oil cooler. I've read the FordDoctorsDTS article suggesting these are caused by and coming from a leaking EGR cooler (possibly only when very hot) over time.
I'm not currently losing any coolant that I can tell, but was losing some a few months ago (during warmer weather), but also had a leaky heater valve that I replaced at the time. Not sure if the leaky valve would account for the total coolant loss (I lost over a gallon in a few weeks).
Here's the additional details:
- 2004 Excursion with just over 109K miles
- Replaced faulty EGR valve (was sticking open) about 300 miles ago
- Replaced stock turbo with new powermax turbo 300 miles ago. Old was rusty and pitted with sticking unison ring.
- I just did a total coolant flush, oil cooler back-flush, Restore and Restore+ and added new coolant filter
- Replaced thermostat during coolant flush. ECT stays pretty close to 190 degress when warmed up.
- ECT/EOT delta is mostly between 15 to 18 degrees, sometimes slightly lower or higher. Not much change after the coolant flush, but may be slightly improved.
- I've been doing pretty regular wide open throttle tests during recent test drives with the new parts above (I'm thinking this may have broken some of this stuff loose).
Here's today's marbles. They're all dry and will crumble if crushed. They are dull gray on the inside - not metallic as they kind of look here............
Ford F-150 - 1997-2003 :: Truck Cranking Over But Starting Only Sometimes?
1996 f150 sometimes it starts sometimes it don't. It is cranking over the starter is in gauging as well as the fuel pump I can hear it.... It's getting spark and I replaced the starter solenoid.
View 5 RepliesFord Transmission :: 4R55E - Truck Starting In Third / Downshifts During Deceleration
I bought a 95 Explorer with a known bad transmission, rebuilt it (broken band and chipped intermediate apply piston), put it back in, and now it's acting odd.
It wants to start in third. I can manually start it in second (first rarely works), shift it to drive at about 30, and it's fine. It shifts into OD, locks the TC, and when given a bit of gas kicks down to second. It downshifts during deceleration, but once I come to a complete stop, it'll try to start in third again. The only transmission code it's giving is for incorrect first gear ratio, there is an off and on engine code for the EGR pressure sensor as well.
Ford F-150 - 1997-2003 :: 2001 5.4L Truck Will Crank But Not Starting
I drive a 2001 ford f150 lariat 5.4L. My truck will crank but not start, i am getting complete spark, and have ran a full fuel pressure procedure, and am getting complete fuel pressure, there is no water in my gas, everything checks out how it should. I ran a test on my cluster and it showed a code that said i am not getting connection to computer to start. I removed the cluster and repaired all loose wires properly, and it still wont start! I have had many people look at it and they said it could still be a bad cluster.
View 13 RepliesFord F-150 - 1997-2003 :: No Activity With Cluster When Turning Key On / Truck Not Starting
I have a 2002 F150. I have an intermittent issue with truck not starting. It turns over fine but will not start. Also, when having this issue, there is also no activity with the cluster when turning the key on (other than lights lighting up); the gauges will not move as they would normally when turning key on. I have checked every fuse inside / out. I have checked the fusible link at the battery as well as any other connections I could locate around the solenoid as well as disconnecting the ECM / computer and re-plugging it back up. Typically, after letting the truck sit for a day or so, it will start back up until next time.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Truck Is Starting To Surge A Bit Like ICP Sensor Going Bad
I started having an issue with a rough idle soon after startup about a month ago. I thought it might have been stiction so I added some Archoil stuff the other day to my oil interval change and although I have not put too many miles on it, the rough idle is still there.
At startup the engine runs great. I did notice a few times a little longer than normal crank (~3 seconds) where other times it fires up in less than 1 second. This has happened twice in the last month. Once the engine runs for about a minute I get an uneven idle......I wouldnt necessarily call it a miss per say. I took some readings for the ICP and IPR and can provide them if someone needs them. Once the truck warms up it seems to idle better but still not 100%. I have no power loss, no hesitations jut a weird idle with intermittent surging while in gear.
The truck is starting to surge a bit like an ICP sensor going bad but not as pronounced as the last time this happened to me 4 years ago. Basically trying to get opinions as to what it might be or what to check next. I am leaning toward one of three things.....stiction, ICP or IPR valve (original). FICM voltage is good but my fuel pressure gauge broke, but the blue spring upgrade I did.
Ford 6.0L Power Stroke Diesel :: Truck Would Die After Starting Then Start Up Again After A Minute
2004 6.0 Diesel. First the truck would die after starting, then start up again after a minute. Then the truck wouldn't start at all.
Trouble codes indicated low voltage on all injectors leading me to conclude a dead FICM. Replaced the power module in the FICM and reinstalled, but still no start.
48V at driver's side screw under the cover. 12V at the next screw, the next appears to be ground. The passenger side screw is 0V. One post indicated that should also be 48V - is the true?
I probed the power coming in - logic fuse is good. 50A fuse in the cab is good. Relay seems good.
The Ford FICM diagnostic indicates 12V power should be coming in on FICM connector X3 on pins 7, 8, 4, 23, 24, 25. I have 12V only on pins 7, 9, and 27. When I pull the relay I lose power on pin 27.
Ford 6.0L Power Stroke Diesel :: Truck Dies Within A Minute After Starting
Parked the truck last night and all was fine. Went to start the truck today and let it warm up before hooking up the trailer and it dies withing a minute. Go to start it again and nothing. End up killing batteries. Checked for codes and had a bogus EGR code P0404. Bogus because the tune I run doesn't have the EGR enabled and it is deleted. Still plugged in though.
Hooked up dual battery chargers and sent the boy to pick up fuel and oil filters and oil. It was over due in both areas. Changed both and still no love. So I drag out the laptop and set up my AE to monitor FLP, FLM, IPR, ICP, ICV, Sync.
KOEO
FLP 11.00
FLM 47.0
ICP 0
ICV .24
IPR 14.25 odd right?
Synch 0
Cranking
FLP 9.6
FLM 47.0
ICP 800-1600 varied the longer I cranked
ICV 2.2
IPR 14.24
Synch 1
still no start.
Still no codes.
I then cycled the IPR through AE a few times and turned the key. Damn thing fired right up.
Idling
FLP 11.0
FLM 47.0
ICP 875
ICV 1.4ish
IPR 26.4
Synch 1
I pushed the RPMs up to 2500
FLP 11.0
FLM 47.0
ICP 2200 iirc
ICV 2.24
IPR 42.0ish
Synch 1
Turned the truck off and restarted it a few times. No issues. Turned it off and pulled the positive cables and put the chargers back on it.
So the question is .....Is the IPR sticking on me? I just replaced the HPOP in the spring along with the up pipes. Made sure everything was clean. I actuated the IPR and cleaned it out. Put a new screen on it had zero leaks.
Ford F-150 (2009-2014) :: 2010 Truck Will Crank But Not Starting When Turn The Key
Yesterday the truck run Perfect. Got home and shut it off. This morning I get I. Turn key and the truck will crank but not start. After it tries to start the oil light comes on. I Che ked the oil and it was 2.5 its low. Added oil and it still isn't starting! 2010 f150 5.4l ....
View 3 RepliesFord F-150 - 1997-2003 :: 1998 Truck Not Starting After Sitting Overnight?
I have a 98 F150. The motor was replaced three months ago and have had no problems until now. The truck had trouble starting so i put an alternator on it. Fixed for a while and then it started blowing fuel relay fuses. I replaced fuel pump and filter. Truck has trouble starting after sitting overnight. When I am driving and floor it, once it hits about 4,000 rpms, the truck bucks like its the transmission but the rpms drop and then pick back up. Fuel pressure is right where its supposed to be.
View 1 RepliesFord Excursion :: V10 Hesitating After Starting - IAC Valve?
Quite a few posts on this on the V10 forum. Mine Ex has been hesitating after starting (bad after a few days of no use) so I took off the old one and put on a new one. I'll clean up the old one and use it as a backup. Best to lay your body on old carpet on top of the engine, cause this value is right under the windshield, behind the air intake. Took about an hour with some swearing involved. DO NOT DROP tools, screws, gaskets, etc!
First few pics of where it's at .....