Ford Excursion :: 2000 - High Idle Intermittently?
I have a 2000 X V10 and am having an intermittent high idle condition. I have searched the forums and found some useful info but nothing that addresses this issue. Here's what I've done. New IAC, found PCV valve hose leaking-replaced also new valve, found another vacuum leak-repaired, tested TPS and that was fine according to the specs I found. So here's my problem-upon starting engine occasionally "stumbles" then roars to life idles 8-1100rpm. Drives well till stopping at an intersection and idles 1100-1200 rpm.(lots of brake) Can pull into parking spot place in park and will idle up 1500-1800 rpm and then only drop to 1200 or so. I have checked everything I know. ALL these idle conditions are INTERMITTENT. (and yes I did check for codes "0" ) There is no loss of power.
View 8 RepliesFord Excursion :: 2000 - High Idle In Park And Neutral
I'm trying to find out what I need to check or replace to get my 2000 Excursion to idle at normal rpm's in park and neutral.
View 11 RepliesFord Ranger / B-Series :: High Idle At Start Up / Revs Up Over 2000 RPM
I have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
Ford Excursion :: 2005 - High Idle Wiring?
I have a 2005 6.0L Excursion. I'd like to do the high idle mod. From looking in the tech folder there are two options.. Option #1 being for 2003-2004 trucks and Option #2 being for 2005+ trucks. The assumption for Option #2 is that there is wiring from the factory for the upfitter switches. My engine build is a 2004 and I could not find any evidence of the orange upfitter wires so I proceeded with Option #1.
I find wire 294 (white/light blue strip) with no problem.. What I can't seem to find is wire 322 (light blue/yellow strip). I can find the 4 dummy (extra) wires to the engine compartment (Red, White, Blue, Black solids) yet I only find 3 blunt cut wires capped with tape... The colors on those are white/orange strip, light green/white strip and yellow/white strip - no sign of the light blue/yellow strip wire.
Is there something unique about the 2005 Excursions?
Ford Excursion :: V10 - Hanging Idle / High RPMs
Not really sure if the V-10 is supposed to be this way or not. I've had quite a few of the 4.6 and 5.4, both the 2v and 3v variant. Never had them do it.
Basically, my V-10 doesn't idle down easily. I can do a neutral rev and it will hang out from 1,000 to 1,500 rpm for maybe 2-3 seconds, then drop to normal idle revs.
While in gear and slowing to a stop, it feels like the motor is fighting the brakes and I have to press harder to stop. It also comes off the transmission when going 35-40 mph and letting off the gas. Causes a weird lurch if I have to get back on the gas.
Not dangerous or anything of that sort, but very very annoying. And I feel it's costing me some MPG's since I drive 99% city and have lots of stops. Probably 1-2 MPG at max. Back in my 2v Mustang days I remember some of the guys were modifying the 4.6 2v IAC because of similar complaints. I'm trying to dig up that mod, but it's been a few years.
I plan on cleaning the IAC this week when I get the time
Ford Excursion :: 2000 - High Beams Not Working
Low beams work fine. When I push the Multi-Function lever on the column forward to activate the high beams, I have no lights at all. When it is in low beam (middle) position, low beams work fine. When I pull back for click to pass, only the low beams are active. No high beam indicator in instrument cluster. I have:
1. Replaced both headlight bulbs
2. Replaced the multi-function switch on the column. Checked test pins on switch (MF) they are hot when in either high beam position or click to pass position
3. checked fuses (interior)
#8 - power on both sides of fuse
#16 (15a) High beam headlamps, instrument cluster. ***NO POWER ON EITHER SIDE***
4. checked fuses (engine compartment)
#10 - power on both sides
#21 - Power on both sides
#23 - power on both sides of fuse
Ford Excursion :: 2000 - 4X4 Low Works But No 4 Wheel Drive In 4X4 High
I have the ESOF in a 2000 Excursion. I went to use 4X4 high and it would not give me 4 wheel drive. light on dash said 4X4 but no 4 wheel drive. I was in snow and only rear wheels spun. When switch is placed in 4X4 low I get 4 wheel drive.
View 1 RepliesFord Excursion :: 2000 V10 - Hard / Rough Shift From 2 To 3 At 30 - 40 MPH With High RPMs
My '00 V10 4x4 w/ 163k miles has had a rough shift from 2-3 (30-40 mph) with high rpms. If I let off the throttle before the shift I can get it to shift smooth, but if I don't let off the throttle it can shift really hard. I only have this issue from 2-3 and it has not gotten worse since I bought the rig almost two years ago. Driving conditions are around town on occasion and for towing a 3k pound pop up. Maybe 2k miles a year so far? The hard shift happens whether towing or not.
I have done just a drain and fill on the trans fluid a year ago. Have not had time to change the filter (even though I have read it's not necessary). I am planning on doing another drain and fill soon along with the filter since I have one and cleaning out the trans pan.
When searching on FTE I read a post about the accumulator springs that can go bad and was wondering if maybe this is the problem? Since I am planning on doing the filter change I was going to do the spring replacement while the pan was open.
Ford Excursion :: 2000 - Up And Down Idle Speeds
OK, Got this 2000 Excursion with 6.8. Recently, it just won't hardly idle, the code says MAF, but it ain't cause I bought a new one.
The Idle is like this: with MAF plugged in It starts and the rpms shoot up to appx 1200 for about 3 or 4 seconds, then it goes down to a point where you think it is going to stall, BUT at the last second it goes back up to 1200 rpm. It will usually do this for 5 or 6 times, but eventually it does stall.
If MAF is NOT Plugged IN it will start and idle perfectly, but the moment you push the Gas it will barely run at all.
Ford Excursion :: 2000 V10 - RPM Fluctuating Down At Idle Once In A While
My 2000 V10 is throwing some codes. The truck drives great, the only thing I notice is the rpm fluctuating down at idle once in a while. It doesn't stall, just not smooth. Here is the log from my torque app that I saved yesterday while driving: Where should I start ? Clean the MAF first ? oxygen sensors ?
Current Fault Log
------------------
P0136: O2 Sensor Circuit Malfunction (Bank 1 Sensor 2)
P0172: System too Rich (Bank 1)
P0175: System too Rich (Bank 2)
Pending Fault Log
------------------
P0153: O2 Sensor Circuit Slow Response (Bank 2 Sensor 1)
Historic Fault Log
------------------
ECU reports no historic faults
Other discovered fault codes
(possibly pending, current or manufacturer specific)
------------------------------<wbr>----------------------
ECU reports no other fault codes logged
End of report.
Ford F-150 - 1997-2003 :: 2000 - High Idle With Codes
I will try to keep this short. Picked up a 2000 f-150 4.2 for my nephews first truck last night. Bought it blind against my better judgement, but the price was right. Got it home, odometer didn't work, fixed the solder joint and was happy it only had 132k on it. Heater core was plugged solid. Got it flushed and at least now its has luke warm heat until I have time for a full coolant flush and new core.
Next on my list is the high idle and engine lights. Its idles around 1300-1700, cold or hot sometimes it drops down. I only have a cheap scanner, but I have 2 codes. PO171 and PO174. Where should I start with diagnosing this? I would assume vacuum leak. Any common spots to check on these?
Ford Excursion :: 2000 - Dies In Gear At Idle?
I have a 2000 excursion V10. It will die in gear forward or reverse the overdrive light flashes and cel shows code p0720. I have new plugs and COP on all 10 cylinders. I have replaced the differential speed sensor and the sensor on top of the transmission. I have a basic code reader it shows at the time it dies the vehicle speed is 70 mph while the speedometer shows 0. When I unhook the abs module it still has code p0720 but it does not die. I am replacing the abs module?
View 8 RepliesFord Excursion :: 2000 V10 - Won't Idle Or Stay Running?
This is for a friends gasser V-10. It has a new fuel pump and oil change. Wont idle or stay running?
View 9 RepliesFord Ranger / B-Series :: 2003 3.0 V6 - High Idle In The Mornings When Cold About 2000 RPM
Truck is a 2003 Ranger EDGE 2wd auto w/140K miles (looks new) that was a one owner truck I recently bought. Came from Texas and is clean and was well maintained I got all service records up until I bought it in the fall last year. OK now the problems...
First...it has a high idle in the mornings when cold about 2000RPM. After it warms up it settles to about 800-900RPM but is VERY ROUGH to the point where it feels it will stall. I DID replace the spark plugs and the plug wires look newer and are not OEM. I DID remove and clean the IAC and it does not look very dirty but I did slightly clean it anyway.
When I did this I disconnected the battery for 20min. After I put it back together it ran smooth for about the first 10 minutes then same rough idle came back. I was told this truck has no EGR so that's not an issue. There are NO CODES and when I ran my pocket scanner nothing comes up either. Should I just go to NAPA and get a new IAC anyway? What else can I do?
Ford Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesFord Excursion :: 2000 Won't Start / PCM Is Bad
I've had a lot of problems with this truck and strongly believe the pcm is bad so i bought a used one now it wont start. Just to let you know i did put old one back in to see if it did run with it and it did. I spoke to the dealer they say I have to bring it in to program it for the PATS. I know its got to be programed but does it have to be the dealer.
View 10 RepliesFord Excursion :: 2000 V10 - No Start With Key
I have an intermittent problem with my 2000 Ex V10 with factory remote start. Sometimes when I put the key in to start the truck, I get nothing. I believe the theft light flashes but I am not entirely sure. Sometimes after a few tries with turning the key it will start. If I hit the button for the factory remote start it always starts, so I have never gotten stuck anywhere.
This issue could happen 2 or 3 times in a row and then not happen again for days or weeks. It's been going on for a couple of years now. What to look at. There is no telling when it will happen again though.
BTW, I have stomped the brake pedal and I have moved the gear shift when it happens and sometimes on retry it starts and sometimes it does not. When I just keep trying the key sometimes it eventually starts too, so I do not think it is the safety in the brake pedal or in the shifter, but I could be wrong.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - High Idle / Over Drive Light Started Blinking
OK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.