Camry :: 1991 - Timing Belt Changed And Now Engine Won't Start
I have a 91 Camry and have just replaced the timing belt and water pump. I thought I did everything right. I made sure the Crankshaft Pulley was aligned to TDC and I turned the Cams to the right marks. I turned the crank by hand numerous times and everything lined up.
I lowered the motor back on to the mounts but didn't connect all the belts to the alternator and compressor. I just wanted to see if it would fire up. Well nothing happened, it turns over but won't start. I pulled some of the plugs and they are bone dry. Sprayed some starter fluid into the throttle body and still nothing. When I turn the key to Accs. Shouldn't I hear the fuel pump wind up? I can't remember but I don't hear a thing.
So my dilemma is, did I screw up the cam/crank alignment and just don't realize it? Like I said all the marks line up fine. Do I need to put everything back together i.e. the Cruise Actuator, Power Steering reservoir, and all belts before I can start it up? It seemed to me I would at least get a hint off life without putting everything back. Then again, I'm not mechanic.
Passat (B5) :: 2002 - V6 Tip FWD - Missing Coolant After Timing Belt Changed
My car recently had its timing belt changed, it's got about 83k miles. up until then there had been some oil loss, but there was some leaking found around the valve covers so the gaskets were done. my mechanic did a full tb change, including the water pump. he said that the coolant was pretty cloudy when he changed it too.
When I got the car back, the coolant filled the tank to about half. it was running and warmed up (had just been driven about an hour) at the time. this was a couple weeks ago. i haven't driven the car since then as its my wife's ride. today, after i got to work (hour on the highway) and turned the car off, i checked the coolant level. it was at the min line.
Now of course, my first thought is "oh crap, am i really gonna have to do a head gasket now?" But I'm wondering what else might be going on, particularly after a TB change. Also, the car has been running kind of like crap as of late. I changed out the spark plugs, which were clearly OEM, and that worked immensely, but after a ride on the highway for an hour it's a bit rough getting off the highway. Dunno if it's related - my mechanic also thinks i need to replace my wires too, so perhaps it's just that.
So far it doesn't look like my oil is being consumed, though i need to pay more careful attention to that as the days go on. i do get a burning coolant (i think. could be oil, but I'm pretty sure it's coolant) smell from the vents when i warm start the car and turn on the heat. it goes away in about a minute or so. when i first got the car back, my mechanic said it was due to the coolant he spilled all over the engine, but after two weeks i wonder if it isn't something else. i suppose it could be, but the car's been driven about 400 miles since and i would think it would be gone by now. maybe i need to clean the engine to be sure? So, questions:
1) Is it possible that there was some air in the system, and that the air worked its way out, causing the overall level to go down?
2) Are there any likely areas of the TB job that could cause this? i don't recall it ever consuming coolant before, and at this rate, i certainly would have, i should think - we had the car for a year before this.
3) The car had a bit of sludging in it - guess is that it never had anything but dino oil before. So I changed it out with some 502 rated oil and my mechanic advised me to drive it hard every so often and then change it out before my normal interval. today i put it into manual mode and got my rpms up around 6000. could the high rpms have led to consumption in some way?
At this point i'd like to collect as much info as i can about this before making any decisions about how to proceed.
Acura - Integra :: 1990 - Replacing Timing Belt?
My 1990 Acura Integra is on her 4th timing belt...still going strong after 25 years! Long ago, I was told by the people who worked on my car that it was best to replace the Timing Belt every 60K. My Manual says inspect at 60K but replace at 90K.I typically have changed it at around 65K....and now it is a bit beyond the 65K mark for this timing belt ( also do the water pump, etc) as the car is now at 262,327 miles.I am tempted to wait a bit longer, as it is not even close to the 90K mark.
View 19 RepliesFord - Escort :: 1999 - No Start After Cranking / Plugs Wet With Fuel
99 escort 2.0 will not start. Has spark, fuel pressure, and 100 psi compression in each cylinder. After cranking for awhile , pull the plugs out and the plugs are wet with fuel. There is no answers anywhere on the net, but apparently there are others like this out there. No codes also.
View 1 RepliesEscort :: 1990 - Random No Start Condition When Cold Outside
A friend of a friend has a 1990 Escort 1.9L automatic with a TBI setup. It has a random no-start condition that only seems to act up when its cold outside (below 20 F). I've only seen it act up once with minimal testing equipment, so I'm digging for answers.
The injector fires normally and flooring the pedal goes into clear-flood mode as it should. It has spark, but sounds out of time. It will attempt to fire unless the pedal is floored long enough to take fuel away. Starting fluid in addition to the fuel makes minimal difference, but results in intake backfires when you stop cranking. After a random amount of cranking, it will eventually fire and then the issue goes away completely.
Once it fired, I was able to shut it down and restart it indefinitely with no hesitation. While running, it shown no signs of being out of time, vacuum leaks, etc. I have very little experience with the EEC system, but friends suggest a TFI module. A weak or mistimed spark seems to be the cause, but I'd like a second opinion. I shook and moved every wire I could find and checked the TFI pins for corrosion - no change.
Santa FE SM (2001-06) :: 2004 - Timing Belt Broke And Turning On Ignition Switch Blows CPU Fuse
Son has a 2004 Hyundai Santa Fe 2.7 motor. The timing belt broke before we could replace it. Long story short, 24 valves, gaskets, timing belt, water pump, new belt tensioner and new pulleys. The motor is back together. The only problem is when you turn the ignition switch on, it blows the CPU fuse. The only electrical part we replaced was the purge valve.
View 3 RepliesFord - Ranger :: 1999 - Broken Timing Belt / No Start After Replacement
2.5 Litre ... Okay, I've done this on other cars, both Fords without a problem but now I'm stuck on the no start situation. I have spark and my fuel pressure is 60 psi. About to do a compression test. Only issue with replacing the belt is that no matter how many times I try removing and installing it I'm always 1/2 tooth off after rotating the engine a couple of times but that shouldn't be enough for a complete no start. Tried starting fluid. Replaced cam sensor. new plugs. checked firing order. I have spark at #1 according to my test lamp which plugs inline.
View 6 RepliesFord Aerostar :: Engine Cranking While At Start Up And After Turning Off?
I've got a 1993 Ford Aerostar XLT. Was running great until yesterday, when I turned the ignition and got nothing but a click every time the key was turned. Checked the battery (had power), bridged the relay (just got clicks but didn't turn over)....so I concluded the starter was bad.
I installed a new starter motor/starter Selinoid today. The van started right up, but next start the engine kept cranking (even while van was running and after shutting off)...I had to disconnect the battery cable for it to stop. Next start the problem didn't persist...but the time after that it happened again.
Any thoughts as to what is going on, or where to start in tackling this problem?
Accent LC (2000-05) :: Car Won't Start After Timing Belt Replacement
I just finished replacing my timing belt, water pump and all belts. I made sure to double check the timing marks lined up via this pic:
Timing belt diagram
I put everything back together and no go. I am not sure what to do now. Should the crank sprocket pulley be in a special starting position? I see is has a "1" engraved on it.
Dodge - Stratus :: Replaced Timing Belt Now Won't Start?
Brought my car to a garage that someone suggested to have a new timing belt put in. After I picked it up I was having problems ((I would try and start car but it would take a few trys to get it started)I called garage told them i thought the timing belt needed to be adjusted. They told me that was not the problem but i needed some censor. Well now my car wont start at all so i brought it to another garage who tells me that the timig belt was placed wrong. My question is..Now what? lol. Do I ask for my money back seeing that they didnt fix it? Do i have the same garage just fix it?(i didnt like them in the first place so really dont want to go back. If i do ask for them for money back and they give me a hard time,what can i do? or who do i call first?
View 4 RepliesAccent MC (2006-11) :: 2008 - Won't Start Up After Replacement Of Timing Belt
The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).
When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.
So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.
Golf IV / Jetta IV :: Car Turns Over But Will Not Start After Timing Belt Replaced
I just got my timing belt replaced by my mobile mechanic thats been doing it for years. I saw him do the work and get the timing right. When he was done the car turned on and ran perfect. After about a minute the car just shuts off. Now the car won't start at all. The car turns over but no start. The car ran perfectly before I had this job done.
View 9 RepliesGolf IV / Jetta IV :: 2003 TDI Will Not Start After Timing Belt Replacement
I recently replaced a timing belt in a 2003 ALH TDI & since it will not start. When I took everything apart I found the belt extremely worn & the engine had actually slightly jumped timing. When I replaced the pulleys & belt & reset the timing to the way it would be from factory. When I tried to start the vehicle it turns over fine but will not catch. I double checked all the timing, fuel pump, everything - all okay. I can get it running with ether but will not start with diesel fuel. I also replaced the fuel filter, checked to make sure there was fuel at the injection pump but nothing works.
View 4 RepliesSubaru - Forester :: 2010 2.5X Automatic With Timing Belt Or A Timing Chain?
I was thinking about checking out the above vehicle at my local dealer (Chevrolet). They're asking 15.9k and it has 57k miles. I need to know if it has a timing belt or a timing chain and how reliable is the engine/transmission.
View 1 RepliesPassat (B5) :: No Power And Winding Noise When Trying To Start - Timing Belt Failure?
Car lost power and has a winding noise when trying to start.It does make any weird YOUR MOTOR IS SCREWED noises or losing any fluids and everything power wise works as it should.I thought the starter went bad,with the winding noise,but doesn't explaining the car just shutting off while driving.
View 17 RepliesMazda - Sparkplugs :: 2000 Protege Won't Start After Timing Belt Change
2000 Mazda Protege 1.6l Just replaced timing belt, tensioner, idler, water pump, plugs and coil packs
I have checked the timing about 10 times before puting everything back together by rotating the engin clockwise. No stiff point and marks lining up perfectly every time.
Though when I turn the key in the ignition, the engine cranks but doesn't start.
Can't really check the sparks cause I am on my own, but seems like the spark plugs in 1 and 3 are wet with fuel and 2 and 4 are dry.
Buick :: 2002 - Turning Over But Won't Start After Fuel Filter Changed
I changed the fuel filter. I can hear the pump going and the filters getting gas to it. The car is turning over but it just isn't starting I cannot think of what else it might be and it is stressing me out a ton.
2002 buick rendevous...
Mitsubishi - Endeavor :: Sputtered Out And Won't Start After Timing Belt And Water Pump Replaced
A mechanic has my car and replaced my timing belt and water pump....he said he had it running and then it sputtered out and wont start..i have never had a problem with this car. Just replacing before it went out.. he is missing something.
View 19 RepliesGolf IV / Jetta IV :: TDI Won't Start After Timing Belt Replaced / Cranks And Blows Black Smoke
So i just spent over $1700 at a vw service ctr having a sched 140k timing belt replaced with thermo and fuel filter. This was 3 days ago and when i picked it up it was slower to turn over then got worse and todsy it won't turn over at all even when jumped. It cranks and blows black smoke. Problem is i'm 160 miles from that svc center and it's sunday. There is a vw svc center 14 miles away but i feel like it needs to ho back to where the work was done because it ran great before taking it there.
View 5 Replies