Engines - Mercury - Cougar :: 1999 - Suddenly Lost Power When Driving Down The Road
Description of Problem: 1999 mercury cougar 2.5L V6 automatic trans: I was driving down the road and suddenly lost power. The engine was still running but sounded a little rough so i turned it off. then it wouldn't start. After having it parked for a couple months i started looking ant it and notice that the starter is spinning the flexplate but the harmonic balance isn't turning. It does turn by hand with a socket. After talking to a mechanic i was told a used motor would run. He said i broke the crank or timing chain? I thought if it was the timing chain the harmonic balancer would still turn, he didn't agree. and i thought it was unlikely that the crank would just break driving down the road. What it could be? or how i can narrow it down. If the flexplate or bolts broke off would that cause my problem?
View 3 RepliesMercury - Cougar :: 1999 - No Acceleration / Starts Shaking After 5-10 Minutes Of Driving
I'm not sure whats wrong here but i think its a plugged exhaust or clogged catalytic converter but whats happening is when I drive my car is lacking power huge, sometimes ill push on the gas and it will hardly move and start chugging but if i push down more it will go. When i go on on ramps to the highway as soon as i hit 70km it starts to chug then i have to push the pedal to the floor to get going,then after a while the car will start to shake after 5-10 minutes of driving and i have to let it cool down or it will keep shaking or just go back onto city roads and it doesnt shake as bad. Once im off the highway my car will begin to shake more at 20km and 60km i have no clue why!
View 6 RepliesMercury - Cougar :: When Slowed Down To Come To A Stop Car Acted As If It Wanted To Cut Off By Sputtering
I have a 2000 Mercury Cougar with about 145k miles.
Today I was driving and when I slowed down to come to a stop it acted as if it wanted to cut off by sputtering. As I got down to about 5-10mph the engine shut off (the radio and everything else was still running) I noticed that as I was slowing down right before it shut off, the RPM was going very low, almost down to zero.
I do have check engine, and low coolant level lights on.For the check engine there are a few codes.1. Something with the catalytic convertor2. 02 Sensors3. Transmission slippage4. I think there was something else but I forgot.
I do need new motor mounts. The oil light comes only when I am idle and after driving for a good 5-10min. I changed my oil about a month and a half ago though.The only time there is issues is upon stopping. Driving and acceleration is fine.
Ford F-150 - 1997-2003 :: Runs Rough And Stalls When Stop Or Rolling To A Stop It Would Die
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
Ford F-150 - 1997-2003 :: Starts / Runs But Refuses To Idle
I have recently acquired a 1997 F250 LD (same body as the 150)the exhaust system is screwed(currently rebuilding it due to some IDIOT trying to cut out the cats with a grinder and cutoff wheel) and it won't idle (runs alright with a little finessing of the throttle) but after I get the exhaust rebuilt to where the O2 sensors get the proper flow I was going to clean the IAC valve but was wondering if the exhaust not feeding right would cause idle issues a well. Put things in a nutshell...the truck will run but will not idle. IAC Probs, Exhaust Probs, or combination of both??
View 9 RepliesFord F-150 (2004-2008) :: Starts And Runs For About 5 Seconds Then Stalls Out
I've got 200k on my Lariat. Engine was replaced 60k ago. It's in outstanding shape and is driven a lot. Suddenly this morning I start as usual and it runs about 5 seconds then stalls out. Every start, same thing. So it seems I am getting fuel pressure to start but it doesn't last.
I did replace the Fuel Pump Module within the past two years, due to corrosion of the FPM housing. At that time the truck would no start at all. Could it have gone bad already? I'm thinking this must be an electronics failure. It was perfect all day yesterday. 2004 Lariat 5.4...
Ford Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord 6.0L Power Stroke Diesel :: DTC P0381 - No WTS Light But Starts And Runs Great?
My 03 F250 6.0L Starts and Runs fine but will never illuminate the glow plug/ wait to start light? Scan tool test on GPRM and tells me everthing is OK. Cleared all codes, turn on key, no WTS light and throws P0381 DTC every time. What my problem is?
View 4 RepliesFord Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Starts And Runs For Forty Five Seconds Or So
Trucks been running perfect for 11,000 miles atleast. its last issue was a bad turbo but that was my fault. No issues whatsoever since. 10 miles down the road from work last night truck had a slight miss in between 55-60 for four or five seconds, I put the pedal down and brought it up to 75 or so just to see if it was my imagination and it felt fine so i wrote it off. It ran fine to the house we're working on i wanted to check on before I got home.
Parked it, it idled down to 650 before it came back up to 750 and it never does that and sounded different then it usually does. so i felt something was definitely up. i shut it off, was at the house about a half hour before i decided to head home, started and ran fine, three miles down the road the slight miss came back, it seemed to go away if i got on it pretty good and when i let off but just cruising with slight throttle it had the slight miss.
Got to my road where i had to slow down and turn and it idled down and died. I coasted over, unplugged the icp sensor and it cranked for 10 seconds or so and lazily came back to life. I got it home running decent and parked it. Scanned it with my old super chips tuner and it came up with a p0340 camshaft position code.
Matched my symptoms i felt so this morning i decided id go back to work and grab my spare out of my wrecked truck. truck started and idled perfect. made it to the end of my driveway before the miss came back and then it just died. took the car to work, grabbed my spare camshaft sensor and my maximus scanner, came home scanned it, no returning p0340 cam code but i swapped the camshaft sensor anyway and watched icp and ipr data, the ipr voltage is where it should be and rises while cranking while cranking.
ICP is climbing to almost 3,200 psi and it will begin to run when it peaks out. she'll fire for 45 seconds after 25 seconds of cranking or so and then it'll just die. if it sits for a few minutes it takes a few seconds of cranking before ICP will come off of 0. I've come to the conclusion that it is making high pressure oil it is just dumping it as fast as it can make it. I changed the ipr out because that can do it, it didn't change anything so I'm on to believing an injector is dumping it as fast as possible.
Is it possible for something to come undone inside the injector to make it dump high pressure oil or will a bad o ring cause this? i'm leaning towards a failing injector as when it does fire and run its definitely misfiring and i just put new o rings on them when i swapped them over from my wrecked truck but that was like 45,000 miles ago as well..
Ford Ranger / B-Series :: 1992 - Engine Starts And Runs Couple Of Seconds Then Shuts Down
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 RepliesElantra HD (2006-10) :: Door Panels Rattle When Car Runs Over Small Dividers On The Road?
I've got a 2010 elantra that's pretty mint still, but for some reason the door panels rattle either when listening to music with a good amount of base, or when the car runs over anything (like the small dividers on the road).
Its pretty annoying sounds and I am curious if its just mine or if other elantras have it as well (2nd owner so I have no clue if the cars always done it ).
Ford 7.3L Power Stroke (1999-2003) :: Truck Starts And Runs But Throttle Doesn't Work
So I installed my chip today. It's got anti-theft, high idle, stock, 50, 75, 100 tunes.
With the chip installed the truck starts. In all tunes except "High Idle" it idles at about 1000... normally it would be like 500-600. High idle position works (1100-1200 RPM). Anti-theft position works - it kills the truck. The throttle does nothing when pressed no matter which position it is in. Stock, 50, 75 or 100.
I removed the chip and the truck runs fine. Did these guys send me one for an automatic? Or do I have the wrong computer in my truck? My computer code is DAC3 and the truck is a 2000 with a manual transmission.
Ford Super Duty (1999-2016) :: F250 Starts And Runs Well But Every Once In A While Pedal Just Stops Working
I have a 2000 F-250 Diesel that has started acting strangely. It starts and runs well, but every once in a while the peddle just stops working. Might be a second or so and then the RPM will go up. Or you may be running down the road and all of the sudden it just stops acting like it is getting enough fuel. Same thing it might last a second or so. Sometimes it might happen 4-5 times in a row over a few minutes and might not happen again for a day. Truck does not stall when this happens. It just does not go like it should.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Runs And Starts Perfect But Under Medium To Hard Acceleration It Bucks / Sputters
Starts good cold and hot. Taking off like a grandpa on an evening drive don't notice a thing. Only codes that keep coming up are 2614 and 2617 which are cmp and ckp open curcuit codes and a software incompatibility code for FICM which is due to the updated software in the fresh FICM I installed. HPO pressures are good, has boost, idles smooth, revs nice when in park. New injectors (cause it was running rough especially cold before) and CMP and CKP (because of the above codes and didn't change)and ICP and IPR (last 2 installed because of HPO codes that are gone now with the IPR and ICP). Fuel pressure is 65psi (updated spring). When you step on it while driving it sputters and bucks like it's out of fuel, let off the throttle a bit and it purrs like a kitten. I'm a little stumped. I think it puffs a little white/blue smoke while it bucks.. not much tho. and it comes in little puffs. Took off filler cap and there is almost no blow by.
View 6 RepliesCelica :: Car Starts Up / Runs For About 5-10 Min And Then Shuts Off
My car starts up and it runs for about 5-10 min and then shuts off. then it will not start again while it is hot, if i leave it sit overnight then it will start again but the same problem will occur. the engine also has a misfire from the moment i start it up, how to diagnose this problem. And after you diagnose it can you tell me ways i can check the problems. for example if you say its the fuel pump tell me how to check to see if my pump is working.
Country: United States
Make: Toyota
Model: Celica GTS
Year: 2000
Engine: 2zzge
Already Tried: Here's what I've done to my car recently: I have new engine coils, new fuel filter, new spark plugs, new thermostat. I got my fuel injectors cleaned, new mass airflow sensor, new water pump.
Ford 6.7L Power Stroke Diesel :: TPMS Warning Go Off On The Road
Had my TPMS warning go off yesterday on the road 400 miles from home. Checked all the tires, all within spec and continued on. But started to wonder if the spare tire also has a TPMS unit and it could be the spare fell below the threshold. I have not checked it yet, but figured I would ask if the spare also has TPMS.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts And Runs With Rough Idle For About 10 Seconds When Cold
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesCamaro :: Engine Starts And Runs Well For About 15-20 Minutes Then Shut Down
Here is my question.. 94 Z28 38K 6spd. Starts right up and runs well, for about 15-20 minutes then will shut down( like the key was turned off) When this happens I have no signal to either the ignition module or to the injectors.
This car was damaged by an idiot that flooded the dist. with coolant doing a flush. They replaced it with a Advance auto remain. This is when the trouble started. I did replace the I/M with an AC OEM Module, no change, verified all wiring from the computer to the Dist. and I/M. All checked out. I am thinking that the cheap remain unit is my problem and am looking to get the MSD Opti spark system to hopefully fix and to prevent this problem from happening again.
I cannot retrieve codes (94 won't flash CEL codes). Is there any other method of diag I could use to verify my suspicions. Oh, there is not response from the Tech either once the engine dies.