Ford Brakes/Suspension :: Bolt Stuck In Leaf Spring Bushing
I am replacing my rear leaf spring hanger and shackle. I have one side done and the other side the old hanger is off. I am ready to install but the bolt/ bushing in the leaf spring will not come out. I tried every thing with what i had for about 2 hours. Is there a tool to remove these things similar to a ball joint press.
View 14 RepliesFord Brakes/Suspension :: Leaf Spring Plastic Bushings / Spacers Worn Out - Squeak Noise
On my 99 at the tip of the springs there is what looks used to be plastic wear spacers between the leafs. Mine are worn out and I think it is part of a squeak noise I am chasing.
What that part would be, where I could get them, and do I have to break down the leaf assembly to change them or could I raise the truck by the frame and take the load off the springs enough to get the in?
Ford Brakes/Suspension :: Replace Front Springs With Airbags
I am lowering the front end of my truck 3" using DJM Dream Beams. I have cut out the rear springs and replaced them with a four link lowering it 4" and installing an air bag suspension. I would like to run air bags up front, as well, but haven't been able to find much about that. What size to use?
View 7 RepliesFord Brakes/Suspension :: 1993 F150 - Coil Springs Leaning Forward
I am doing an sas on my 93 f150 short bed. my issue is that I've made coil spacers out of 1/2" thick by 3" tall by 4" in dia.... as you can see strength is not an issue here. i bought 6" lift coils for a 93' then decided to just say f it and throw a d44 straight axle under it. the springs on a 78' d44 are the same dia. top to bottom. 93' springs get smaller at the bottom so i made this spacer for two reasons.... 1 to have smaller seat for the bottom of the coil.. and 2 so i could make up the spring length difference between the two springs. The spacers are leaning forward due to the 7 degree c bushings on the radius arms.
View 1 RepliesFord Excursion :: Noisy Front Leaf Springs?
Been chasing this for a few weeks and getting fed up. Have a bad metal on metal "creaking" noise from the front at low speeds.
Background - Replaced springs with X code front and modded C code rear from Junior at ATS. Also replaced shocks at the same time. All hardware tightened with weight on suspension. Have rechecked torque on ubolts many times, even loosened and retightened both ends of the shackles, sway bar links, shocks, etc.
Can't get the noise to go away. Hard to pinpoint exactly where it's coming from but you can "feel" the noise in the back half of the front springs.
Ford Excursion :: Checking Front Leaf Springs?
Trying to figure out if my front leafs are factory or not. I assume so but they look extremely weak for a 9k rig.
View 14 RepliesFord F-150 - 1997-2003 :: 2000 - Leaf Springs Rattles - Fix?
My wife's 2000 SCAB 4x4 has been rattling for a while now. I have been able to figure out that the culprit(s) are the metal bands on the leaf springs, which are somewhat loose and causing the rattle. I have squeezed them with a large c-clamp on a couple of occasions, which seems to have provided a temporary fix, but as soon as the suspension cycles fully they stretch out again, and begin making noise. How to tighten them permanently? Or is there a replacement/upgrade to fix it?
View 2 RepliesFord F-150 - 1997-2003 :: New Leaf Springs Have Slightly Different Arch?
I bought some new leaf springs for my 2000 F150XL and noticed one is different only slightly, it being in the arch one is 7 15/16 which is correct, but the other is 8 1/8. how much variable do they allow, will it make that big of a difference or will i be able to notice it after there on. I am happy with them but don't want to put them on and then the truck set uneven??? the reason for replacing the ones still on the truck is they are twisted and apparently broke they are 2/1 springs and having the new ones i can tell the #2 spring on the truck now are shorter like the ends are broke off and the clips moved around allowing for them to twist, so i really needed new ones.should i put the taller arch on a particular side or should i just put them on....
View 2 RepliesFord Super Duty (1999-2016) :: Wheels Rubbing The Leaf Springs
This is my dads f250 build date of 9/03. I know these wheels are not the factory xl wheels. I also think they changed something with the wheel back spacing somewhere around this time. He is running 285/70/17 bfgs and is rubbing the leaf springs pretty good. He ran this same size on his previous 02 model with no rubbing. Can he get away with 1/4 spacers? What years these wheels are from? And the backspacing differences, if any. His 02 had the chrome large bullet hole style wheels.
View 5 RepliesFord Super Duty (1999-2016) :: Spacing On Rear Leaf Springs?
I have a 99 SD 250 diesel, I also have a broken rear leaf spring. My truck has a 3 1/2 in. block between axle and leaf. My question is this. Can I remove the block and install 4" lift leaf springs without messing up my pinion angle? The blocks look square. But someone toldme once they are made to a specific angle for rotating pinion for better u joint alignment. Sounds like it could be true.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Front Leaf Springs?
I tried to replace the rear spring bushing of the drivers side front leaf spring.
Got the nutz off the shackle... The lower bolt was bumping into the front drive shaft and would not come out all the way.
Biggest problem I was having seemed to be I could not get the axle to drop far enough to release the pressure on the bolts in the shackle.
NOTE: I was trying to do this without unbolting the U-Bolts from the axle.
I was under the impression you could do this without unbolting the u-bolts. I have all new hyperflex suspension bushings and would like to get them on.
Ford Super Duty (1999-2016) :: 2000 F250 - Clunk In Front / Leaf Springs Bad?
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
Ford Super Duty (1999-2016) :: 2000 F350 - Softer Ride On Leaf Springs
I have a 2000 F350 that was once a work horse. Its now just my daily. The leaf springs in the rear have 2 broken on each on and the front need to be replaced due to 344K miles on them too. My question is how do I soften up my ride on leaf springs though? Theres a local shop that will do the work, but my rears have 7 leafs / front 2. It used to tow daily but I dont tow anything with it. could I go to 5 in the rear to soften it?
View 14 RepliesFord Super Duty (1999-2016) :: Replacing Rear Block - Axle Won't Separate From Leaf Springs?
I decided to go ahead and do a rear block replacement. I'm going to install the Ready lift 4 inch blocks.
I have both u bolts and nuts off of both sides. Rear stabilizer bar disconnected and both shocks disconnected. However, when I raise the rear of the truck, the axle raises as well. What could be holding it on still? I noticed there's a nut in the middle of the leaf springs. Do I take that nut off? I just don't know what could be keeping it from separating.
Ford Super Duty (1999-2016) :: 2004 F250 - Tire Rubbing On Plastic And Front Leaf Springs?
I just put some toyo at2 295.75.16. On my 04 250. And I've got some rubbing on the plastic and front leaf springs. If a 2.5 " spring left will take care of the rubbing or will I need wheel spacers.
View 3 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Front Tires Leaf Springs Rubbing Even On Slight Tight Turn
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 RepliesFord Brakes/Suspension :: 1997 F150 - Converting Drum Brakes To Rear Disc Brakes?
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Prius V :: Clanking Noise From Front Suspension - H&R Springs
I just had some H&R springs installed and my front suspension is making a funny noise.
It sounds like the front springs are clanking around..
Golf VI R :: Installing VWR Springs - Rear Suspension Unknown Part
I am installing VWR Springs to replace worn stock components on my mk6 R. It appears that the previous owner slammed the car, and removed the "nipple" that holds the rear spring in place from the top. Both upper and lower spring isolators were present.
I am trying to find a name or part number for this unknown "nipple". I tried some combinations, such as "rear spring cap" and "rear spring centering guide". It looks like it would screw into the body, right above the springs themselves.