Ford Brakes/Suspension :: 2003 F250 - Brakes Are Spongy Or Go To Floor
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 RepliesFord Brakes/Suspension :: New Calipers Now Spongy Brakes After Bleed
I'm not too familiar with these trucks, but I've been working on my buddies 1999 e350 ford van.
The other day we were going out kayaking, and the brakes locked up, we were able to drive it home, but it was obvious the brakes were holding the truck back. decided to check it out today, found one front and one rear caliper were sticking, the dual piston calipers only had one working, which I believed to be causing the pads to get pressed together crooked, and caused them to "lock up" or get stuck.
anyways, got the new calipers on and no more sticking, so I bled the brakes started in the front and went all the way to the back, did every caliper. brakes feel firm with the vehicle off, but instantly when the van is started, the pedal goes to the floor. it still stops okay, but the pedal feel is not nearly where it should be.
I got all of the air out of the system, but the abs light is on, and has been for a while. I'm wondering if there is something else that needs to be bled in the abs? someone was telling me about bleeding the abs motor?
Ford Brakes/Suspension :: 1997 F150 - Converting Drum Brakes To Rear Disc Brakes?
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Ford Brakes/Suspension :: 1995 F150 - Right Front Tire / Passenger Side Wheel Is Leaning In
My 95 F150 2WD. The passenger side wheel is leaning in(top) - toed in? and I am A. concerned that this is unsafe to drive it and B. What is the most likely cause and fix? I was just looking for a starting point.
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2014 - Brakes Squeaking - Replaced Brake Pads And Calipers?
We had approximately 7000 miles on our 2014 250 when we first heard our squeaking when we applied the brakes. This happened after we had been driving a while. Took it to the dealer to see what was causing the noise. They found out it was the front brakes. They removed both front wheels to find the inner pads wearing at an angle and the caliper piston boots partly melted in middle. They ended up replacing the brake pads and calipers with new and machined rotors.
View 14 RepliesFord Brakes/Suspension :: F150 - Rear Brakes Lock Up Upon Hard Braking?
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 RepliesFord Brakes/Suspension :: 1999 F150 - Getting Air Out Of Brake Lines?
I am having trouble big time getting air out of my brake lines. I put new front pads and rotors on and also had to replace the brake line coming from the caliper as it kind of crumbled and needed to replace the next line up that goes to the ABS block on the left front. After doing this, I bled that wheel only and at first it was ok until the brake line on the right front at the caliper also broke when I was pushing on the brake pedal with the truck running, spewing fluid all over. I have tried to bleed using a decent vacuum bleed setup from Advanced Auto but keep getting massive amounts of air coming out and when I start the truck and hit the brake pedal, it goes to the floor. Could the master cylinder be bad? I have checked every connection that I made and all other connections and there are no leaks at all. I am stuck in the garage! The truck is a 1999 F150 4x4 with 4 wheel ABS.
View 1 RepliesFord Brakes/Suspension :: 1997 F150 - Brake Pedal Keeps Fading
I recently purchased a mutt of truck, a 97' F150 heritage w/5.4 Triton motor, 1/2 ton 2WD short bed.
Having a brake issue, the pedal keeps fading. I noticed it first while sitting in traffic on a down hill grade. I am holding the pedal and notice it starts to creep down slowly, I pump it up and it firms up then starts collapsing again. So general logic says hydraulics are loosing pressure right?....No leaks anywhere, so it must MC tight?
I have replaced the master cylinder, brake booster, and both rear wheel cylinders. Long story short they all needed it, truck has 265K+ on the body with 95K on the motor. The only thing I did not do by standard is bleed the MC on the bench, I installed and long bled starting with the right rear working my from longest distance to shortest (wheel speaking). So when bleeding I did of course get air coming out because of the new parts but I still have the same fade issue.
I am confident there is no air in the lines, I have bleed a quart of brake fluid through just to be sure. I have read a lot about proportioning valves and ABS stuff.
I will try and get some vehicle specific photos and attach have hit a road block with this. I am leaning towards the ABS valve thingy mounted on the drivers fender that has four lines attached (2 in and 2 out). Other than that it comes down to hard lines which have no leaks.
Ford Brakes/Suspension :: 1990 F150 - Yellow ABS And The Red Brake Lights On
I have a '90 F150 and both the yellow ABS light and the red BRAKE light are on.
It was fine until my buddy did a little brake work for me, including replacing a couple brake lines and a parking brake cable. He bled the system at the lines going into the front calipers because the bleeder valves on the calipers where corroded and frozen. I then replaced the calipers and bled the system properly. Three times. I don't think the problem is from the brake work.
The brakes still work, by the way. The pedal just feels a bit spongy and I think the brakes don't work as well as they could.
If the truck is not running, I can pump the brakes a few times, and it will make a sound like it's sucking air a few times. Then the sound stops and the pedal firms up.
If the truck IS running, it keeps making the sucking air sound no matter how many times I pump it, and the pedal feel stays the same. I think it might be a bad brake booster.
Ford Brakes/Suspension :: 2010 F150 - Brake Fluid In Intake
I took my 2010 F-150 for brake job and ended up with brake fluid in intake!! How that happened?
View 12 RepliesFord Brakes/Suspension :: 1986 F150 - Lose Brake Pedal?
86 f150 4x4
brake pedel goes straight to the floor but if u give it short pumps of the pedel it grabs but barley....master cylinder or the booster?
Ford Brakes/Suspension :: 1995 F250 Truck Does Not Stop Fast Enough When Hit The Brakes
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
Ford Brakes/Suspension :: 2001 F150 - Rear Brake Lights Not Working
I have a 2001 F150. Front brakes replaced a few months ago. Last night, I realized my rear brake lights weren't working. I'm not sure how long they've been out or if it's related to the bigger problem.
While testing the brake lights by pressing the brake pedal, the pedal seemed to give out and sink lower. While driving the brakes worked but only when I pushed the pedal all the way in. Eventually the ABS light came on and stayed on.
Ford Brakes/Suspension :: 1979 F150 - Disk Brake Caliper Replacement / Evaluation
I have a '79 F150 4wd and was wondering what would indicate a caliper needing replacement. I'm already going to replace everything on my rear brakes, they are completely trashed. However, the fronts seem OK, NO indications of leaks or seizing both sides of the rotors appear to be evenly "used" I guess. The inner pads do seem to be thicker than the outer pads is this normal? Anything I should be specifically looking for before I have the rotors turned and put a new set of pads on?
View 5 RepliesFord Brakes/Suspension :: 1989 F150 - Park Brake Won't Disengage When Release Lever Pulled?
my park brake will work when pushed to the floor but when i pull the release lever it will not disengaged.
View 1 RepliesFord Brakes/Suspension :: 2004 F150 - Front Left Wheel Would Start Shaking When Brake
Two weeks ago my front left wheel would start shaking like hell when I brake, not at first but after say may eight miles of driving. I have never been in a vehicle shaking so violently and after proceeding from a stop it would continue until it cooled down. I tore out the caliper and made sure everything was clean and lubed and also to make sure I did not put the pads on wrong. Fast forward one commute and the same crap. I could not go faster than 45 mph without feeling like it was going to disintegrate.
When I got home the damn thing was smoking. I managed to get it to the dealership this afternoon and two hours later the guy told me that the guides just needed some cleaning and grease. They did not want to charge me anything (draw your own conclusion) for it. I was told they drove it up/down hills and it was alright. I left kind of suspicious and four miles later the problem revealed itself again. My next thought it maybe axle end play, bad bearings or joints? Intermittent why? 2004 f150 lariat 4x4 ....
Ford Brakes/Suspension :: 1993 F150 - Rear Brake Locking After Master Cylinder Replacement
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 RepliesVolvo :: Replaced The Brakes But Pedal Still Spongy
My 89 240 is a project car so I am just fixing everything up as new until it's all done.
Replaced the Brake Booster with a fully reconditioned one, a new master cylinder, full pressure bleed, new pads. Now I have fantastic brakes but they feel super spongy still . As an example, I make an emergency stop to check if they are ok and after stopping just fine , the pedal still wants to go down further. I have checked all the flexible lines for ballooning and they are ok .
Ford Brakes/Suspension :: 1994 F250 - Blown Brake Line / No Brakes At All?
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?