Santa FE SM (2001-06) :: Rear Seat Latch Release
I have an '01 Santa Fe and love it, except for the fact that I can no longer fold the passenger side of my rear seat. We recently moved and I guess one of the kids put the rear seats back up and didn't think to make sure that the strap that goes to the latch release was where it belonged, because now it's stuck under the seat. Actually, I think it may be stuck in the latch itself. My sis (a proud '05 SF owner) and I have tried everything we can think of to free it - it was actually quite comical to watch - but no luck. We can feel the strap but we can't get a good grip on it and can't really move it. It folds under the seat right where the latch is, that's why I think it's stuck in the latch.
View 4 RepliesFord F-150 - 1997-2003 :: 3rd Door Stuck / How To Release The Latch
I have removed the panel cover; cables are out - door is still stuck! Is there a way to release the latch? It is the driver side back door - 2001 Lariat.
View 4 RepliesPrius (Gen 2) :: 2007 Can't Find How To Release Back Latch
With the car off and me standing at rear hatch and it is raised I pushed the latch closed manually and I can't figure out how to release it back to the unlatched position. I tried the door locks to no avail.
As an aside I was doing this to troubleshoot why my alarm is going off alot. I have a relative new yellowtop battery installed and will replace the fob battery later.
Sonata NF (2006-10) :: Hood Latch Release Stiff
I noticed my hood latch release getting a little stiffer over some time to the point that my hood latch cable stretched out and didn't work. I fixed it by tying a knot in the cable to shorten the length and now it works fine. HOWEVER, it is still getting stiffer. I unhooked the 2 cable peices where they connect under the hood on the driver side to see if they are sticking, they both are smooth. I also latch the release mechanism (without closing the hood) and activated it easily. BUT still when I use it on the hood, it is very stiff.
View 1 RepliesPrius (Gen 3) :: Back Latch Lock Is Stuck - Door Does Not Release
A thin blanket is caught in the lock of the rear hatch door. I have removed the cover on the utility box inside the car, and moved the lever but that did not work. I can hear the mechanism working when pressing the unlock but the door does not release. I tried pulling the blanket but it does not budge. I don't want to cut the blanket away because I could not reach what is stuck in the mechanism.
View 3 RepliesChevrolet - Silverado1500 :: 2002 - Jammed Tailgate / Latch Would Not Release
I have a new issue with my '02 Silverado, which so far has been a good truck. However, about a week ago when I tried to open the tailgate, the latch wouldn't release. I have yanked on the tailgate with my full weight (260 lbs) while pulling on the release handle, and have not had any success at getting it open.
The release handle seems to work OK, but the internal latch mechanism seems to be jammed in some way. I have even tried parking the truck on different surfaces, just to see if tilting the truck at different angles would loosen the latch, but that didn't work either.
It's as if the tailgate were welded shut. fortunately, most stuff I put in the bed isn't too heavy for me to lift over the gate or the bed sides, but I'd really like to have my tailgate working again. I have even thought that if I do get the gate open, that I'd disable the latch and install a hook-and-chain setup like what trucks had in the early 1960s and prior (since it's a work truck and I'm not planning to part with, it I'm not concerned about resale value).
Tiguan :: Driver Side Door Handle Does Not Release The Latch
This happened a few days ago, that the driver's side door handle does not release the latch and let the driver door open. we can open the door fine from inside. the remote key un-locks/locks the door fine. What I've tried :
- Slamming the door hard a few times,
- Pulling both the inside and outside door handles at the same time
- Greasing the latch mechanism on the door end (what hooks onto the latch)
Today I removed the lock cylinder, but from what i can see with the cylinder removed the door handle looks ok (no broken or missing pieces). What would be the next thing to do?
2010 Tiguan SE
Elantra HD (2006-10) :: Hood Won't Open When Pull The Latch From Interior Release
My hood has ceased to pop open when I pull the latch from the interior release. I removed the panel to see if the cable came undone from the release lever but it is still intact. From what I can tell, the cable seems to be snapped in the middle. I brought the car to 2 different mechanics, both said they would have to do damage to get under the hood. But I've read online and it seems other people are able to do it.
View 5 RepliesTouareg :: 2004 - Passenger Door Latch Frozen Closed And Will Not Release
I hear the electrical activity of the door lock mechanism.....locking and unlocking the door but the door latch is "frozen" closed and will not release. Inner and/or exterior door handles fail to release the latch no matter how many times they are pulled. Red Led on the top of the door pannel functions normally.
View 4 RepliesJetta - Volkswagen :: 2009 - Hood Latch Stuck / Cannot Release The Lever
I have been having trouble trying to release the lever under the hood on my 2009 Jetta. the interior lever seems to be working but when I attempt to depress the hood lever it won't budge! I like to check my oil on a regular basis and I have never had this challenge before. I'm also worried that if I am able to release it that I will not be able to secure it afterwards, rendering my vehicle inoperable. I am strongly considering just taking it for an oil change and "springing" the dilemma on the garage.
View 3 RepliesFord Ranger / B-Series :: 1993 - Clutch Release Bearing Install
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
Ford Aerostar :: 1993 - A/C Not Condensing?
We have a question about our 93 Aerostar. The A/C is working, but not very well. Not cold enough. It is fully charged. We are not able to see any condensation dripping below the car when parked, after running the air. We cannot discover where this condensation is going, or even wbere the hose from the evaporator is supposed to be. Shouldn't it be coming down into the front wheel well area? We have had the van since about 03, and the AC system has been replaced in that time. When the weather is cool (not often this summer) the air works OK, but it isn't keeping up in hot weather.
View 4 RepliesFord Aerostar :: Converting 1993 2WD To AWD?
Is it possible to convert a 1993 2WD Aerostar EB with a A4LD to a AWD drivetrain? I am a Subaru veteran (this is my first time posting), and the mod capabilities of soobs is endless - older 2wd car to AWD is not hard at all on those cars - in fact it is a relatively easy bolt-in change.
Traction on snow (or anything else) in a stock 2WD Aerostar leaves MUCH to be desired (especially when compared to a vintage soob). How good is the AWD drivetrain overall? Is it as reliable and rugged as the 2WD? Gas mileage difference between 2wd and AWD? Handling? Maintenance? Are there different versions of the AWD? If so what are they like? I have a 1993 FSM for the drivetrain, but I don't know how similar other model years are.
Ford Aerostar :: 1993 - Front Oil Pan Leak?
Well I've got an nice steady leak coming from the front of the pan.... running aft of course (downhill, windflow). She's down right now for an AC overhaul and new PS pump/hoses, but I'm inspecting to see what is next to get this stinking oil leakage stopped.
Front HB removal and seal of course, done in situ (in position). But if it is actually the oil pan/seal, can that be done there also? Front of the pan looks tight to the crossmember, and how the internals look (tray baffles, pump pickup) I've no clue if it will come off. Once she is back up and running I'll ascertain where this leak originates.
Interweb searches show the 90-94 4.0L engine is notorious for pan gasket leaks. None of the writeups I've found thus far determine if that pan can be pulled where she sits.
Ford Aerostar :: 1993 - Runs Great Except When Warmed Up
My Aerostar is a 93 extended EB with 4.0, AT, 212k mostly reliable miles, and blue and gold paint that has held up remarkably well. When started it runs great; smooth idle, easy revs, normal as can be. But when that third pip on the digital temp gauge hits Normal the van becomes possessed. The idle will randomly drop or surge or return to normal, the check engine light will come on for a few seconds then go off, all without pattern, just kinda crazy. Today I held it at 2k rpm, then it bogged down to like 800 rpm and lit the CEL, then it returned to 2k rpm and the light cleared, swung up to 2.5k, all while I hold the throttle steady. The light does not always come on when it bogs. I see no black smoke from the exhaust and it smells normal, but it was kinda windy today.
The check engine light is not lit otherwise so I assume no hard codes are stored. I think I found the code retrieval process for the OBDI but I have not done that yet. After reading a bit in this forum I thought to clean the MAP sensor, but I do not have security torx bits to remove it yet. As background a few years ago it had an oil leak from the top rear which I ignored, and it slowly rotted a harness back there till one day the harness died leaving me running on 3 cylinders. My local Speedy Lube guy was ex Ford dealership and knew Aerostars, he did the diagnosis and repair and said it was a common problem. But he has moved on. I was also told I have a torn boot on a plug wire, but there's no way to get my ham-like paws back in there, from front or back, to verify or replace. I mention all this as background, I doubt a bad plug wire is the issue here.
It seems like an odd problem to me because the only pattern is related to operating temp. It is not a constant problem, not an intermittent glitch, but it very definitely goes nuts right when it achieves normal temp. Aside from pulling the codes, which I will figure out tomorrow, any other tests I can run to diagnosis? Any way I can trick this thing into thinking it is cold all the time?
Ford Aerostar :: 1993 - Bogs Under Acceleration / No Power
My 1993 ford aerostar 3.0 is a great vehicle but recently its been killing me trying to figure out what the cause is. I'll start at the beginning. I had a job over the hill in Westwood Ca. Ran low on gas on the way home. Too low apparently. Since i refueled it has a really rough idle and no power under acceleration. After it gets warmed up i get a bad smell of gas and exhaust in the cab.
Now if i turn it off wait 15 min or 12 hours it will run ok for 2 min then back to hell. I has not stalled and i have replaced the fuel filter and a few months back i cleaned the Mass air flow sensor and replaced the TPS. I would love to take it to a mechanic but as i have been living in this old girl for the passed 6 months money is non-existent.
What to do. I have even tried disconnecting 1 at a time... the TPS, MAF, and the 02 sensor. No difference. There has been no check engine light until I tested by disconnecting TPS etc.
Ford Aerostar :: 1993 - Gear Shifter Broke?
I went to put the van in park, and the gear shifter just went all floppy in my hand. I was able to wiggle/jostle it around and get it into neutral or drive, but nothing else. Tow truck driver crawled under the van, and put it into drive for me, and told me it was probably just going to need a new cable or link shaft (tube shaped thing)... My hubby usually fixes these things, but is now living 1700 miles away.
Anyway, the shop called me and said I needed a new steering column, and said something about the 'lower' cap or half??? He quoted me $340 for the job. I am not getting the connection between the gear shifter being loose/floppy and the steering column needing to be replaced? Is this right?
It is a 1993 Aerostar, 3.0 by the way...
Ford Aerostar :: 1993 - Transmission Dropping Out Of Overdrive
I have a 1993 Aerostar 3.0L, automatic. The transmission has started dropping out of overdrive into drive while at speed. It's very inconsistent as sometimes it will drive without incident and sometimes it will barely go into overdrive and then drop back out and remain in drive for an extend period of time. I changed the fluid/filter/gasket thinking it was just overdue for changing but no luck. The fluid level is fine, perhaps even a little high. Fluid looks clean on the stick, so I don't think it was a lack of draining enough fluid. The problem seems to be more pronounced when warmed up.
Also when cold, I've had an issue with it stalling while taking off from a stop. I wouldn't necessarily relate the two problems, but someone mentioned they thought they might both be a symptom of a slipping torque converter or something. But the stalling issue seems to go away when it's warmed up.
Also had an issue with the van not wanting to start when damp. But I attributed this to water getting on the coil or plugs or something. What I could try before taking it to a shop and risking getting taken?
Ford Aerostar :: 1993 - Lack Of Power / Sluggish
We have a 1993 Ford Aerostar 4wd Eddie Bauer edition. This van has 150,000 miles on it. In the past 2 years we've had a number of problems related to the van idling hard and having a lack of power.
First, the van revved high and low and was unable to maintain a steady idle....I replaced the throttle positioning sensor and this fixed the problem. Next, the van was running sluggish and was very slow to respond when you pushed the accelerator....I replaced the oxygen sensor and it fixed the problem.
Currently, (a few months after changing the oxygen sensor and the problem being temporarily fixed) the van is having the same issue as before I replaced the O2 sensor (running sluggish and slow to respond to the accelerator). If you press the accelerator down (even to the floor) it barely responds, you can get it driving at highways speeds but it takes a long time to baby it up to those speeds.
When you let off the accelerator after pressing the petal down it actually sometimes gets a second of power. It also is not maintaining a stable idle (fluctuating between high and nearly dying). I bought a new 02 sensor and installed it but it didn't fix the problem this time. The exhaust smells rich in gas. What else might make the van run like this? Possible solutions for where to look next?