Ford 7.3L Power Stroke (1999-2003) :: Low On Power / Injectors HPOP Or Tune?
So I have a 2002 7.3 Excursion and I think it is low on power. ICP is falling on its face when on a 60 or 80 HP tune. I have some boost leaks at the plenums and will work on that but that shouldn't cause my ICP to tank at full throttle. Following are some numbers I pulled with WOT runs up a 6% grade.
16PSI BOOST
EXHAUST PRESSURE 40
ICP 1900
80%IPRDC
this is with the 60 or 80HP tune on my DP-tuner. If I ease into the throttle I get
2700 ICP with
45%IPRDC
but if I stomp on the throttle it stumbles and ICP tanks.
Running the stock tune I can maintain
2700ICP at
40-45%IPRDC
Is this my HPOP being weak, or worn out injectors, to much of a tune or a combo of all three?
Ford 7.3L Power Stroke (1999-2003) :: White Smoke Only When Barely On The Gas?
My 2001 7.3 is smoking only when barely on the gas. New fuel filter. Don't know if its possible injector going bad or what? Smoke is white not black.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Won't Start - Bad Injectors - Coolant In The Oil?
So we begin w/ another saga for the 7.3l Excursion......
A few months ago it started running like crap, real crap and blowing white smoke like crazy. Well I knew this from a previous episode and I had a bad or multiple bad injectors. I tried to trouble shoot which one it was and maybe just replace the one or two....but no it was worse than that. So Life was really busy it kinda got shoved aside until now.
I pulled all the injectors and had them rebuilt locally ..nice. They ended up being with mech for a couple of weeks because he went out of town...no problem. Well this entire time my rig was untouched and when I got them back #7 was full of water.....great, bad injector cup. #7 was the only one, the rest were dry. So I drained the radiator and the oil and left it overnight to completely drain and installed the new injector cup in #7. Next day I refilled via both heads because the valve covers were off, 4 gallons of oil and a new oil filter. Cleared the cylinders via the glow plugs and commenced to trying to get her started. Nada......just cranks, killed the batteries, recharged over night and left the box on them and still nada....but the oil was still very milky at this point.
So tonight I pulled all the injectors back out and drained the oil again, still a lot of water. This time I sucked out the HPOP reservoir and got a more milky water/oil out and I'm leaving everything open all night.
In the am I plan to check my overflow water level in the hopes it remains at the same level...if so I will reinstall all 8 injectors and refill the motor w/ 4 gallons of fresh oil and try again.
Oh, while I was attempting get her started I put my buddies Snapon scan tool on it and I got the p1271-p1278 codes w/ the buzz test. (low side to high side open circuit between idm and injector) So I found the pin test with everything connected at the idm pigtail and everything tested good. So I'm back to my not so fresh oil anymore is the culprit to it not starting.
Am I missing something here?
Also....another fun filled fact is that I seem to have a fuel leak somewhere at the rear passenger side. Every time my fuel bowl fills up, if I shut the key off it will drain down. Sometimes I can see fuel dripping quite vigorously onto my starter but I can not see where it is coming from. I have while it was dripping ran my hand along the head and the fuel lines and can not find where it is coming from. Any thoughts as to where in the hell this fuel could be leaking from?
Ford 7.3L Power Stroke (1999-2003) :: New Injectors - Crank But Won't Start - Low ICP?
So I got all 8 injectors upgraded and excited when I get them back I put them all in in kind of a rush. And in that rush I left the cylinders full of excess oil. So obviously when I tried to start it hydro locked. Angry at myself. I kept trying to crank hoping it would fire and just shoot that oil out. Nope, so I went back to taking all the glow plugs out and firing it all back out. Put it all back together then tried to fire her up. Took a minute but she started and I let it run for a while. Hit the gas a few times and then it died. Couldn't get it started again. It would just crank, I checked the icp and ipr and the icp did not build above 35 psi and the ipr was at 98.04% so I just figured the o rings blew out when it hydro locked.
So I took it all back apart put new o rings on, took my time and put it back together right double checking everything. Got it all back together and went to start it, it would just crank around 160-170 rpms, battery voltage at 10.6 icp built up to 140 but now it won't build past 40. Ipr still goes to 98.04. The engine ran just fine prior to injector change, I put a new upgraded hpop prior to injector change, new ipr, icp, cps. Everything checks out, but it will not build oil pressure while crank I've killed a set of batteries then went all out and spent 350 at napa for some optima red tops. I did notice the cylinder 7 injector is the AE injector. It suppose to be in cylinder 8, idk if that's affect the oil pressure building up?
But as far as I know, I'm not building oil pressure. So idk if the hydro lock could have ruined something to keep it from building oil pressure?
Ford 7.3L Power Stroke (1999-2003) :: 2005 - Putting New Injectors?
Are there more parts that i would have to get when putting in new injectors in my 2000 f250?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Oil Coming Out Of Spouts On The Injectors?
What causes oil coming out of the oil spouts on the injectors? I pulled my VC to re torque my injectors down and I noticed 2 of mine are now leaking oil out the spouts(when warming the engine). Note I did not say the base of the injector.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Injectors - Which Injector Goes Where
I just bought a 99 F350 with 240k miles on it and got it for a deal because it needed injectors. Ive done the same job to my 97 OBS powerstroke. The injectors were already pulled so I had them sent for rebuild, the problem is I cant tell which injector goes where. is there a trick to figuring out where each injector goes when I put it back together?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Brand New Injectors With Dings In Them?
I paid for brand new injectors and when i took them out today they all had dings and small gouges in the plates,is this normal?they are 180/100 cc
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Lots Of Clatter - How To Test Injectors
Have a pretty good running (I think), 2000 7.3 with 151K that has always been pretty noisy. Lots of clatter. I amjust wondering if there's an easy way to tell if I may have injector issues starting to come up.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Changed Injectors / Cannot Even Get Engine To Crank?
I changed my injectors and glow plugs on passenger side. I tried to start the engine and it wont crank (turn over). I tried to turn over by hand by turning alternator bolt counter clockwise, turns a little bit and then get very difficult. Is this hydro lock? I stuck a suction tube down injector holes and made it to the piston not much oil came out, I think the truck was a little low on oil before I started the project. The starter wont turn the engine over. I even turned the engine over by hand many times before I put glow plugs in to evacuate the cylinders. I don't know what to do?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: No Start After Cups Install And New Injectors
I just replaced my cups because of bad leak. well replaced all cups and injector from a rolled truck the truck ran when pulled. well installed went to start and have tried for 2 days on and off still not start did buzz test and passed , checked oil reserve and was full. When I first tried to start it acted like it was hydrolocked and then hit it again and been turning fine
YouTube ....
Ford 7.3L Power Stroke (1999-2003) :: Additive In Coolant So Injectors Don't Rust?
Someone just told me I need to put additive in coolant so the injectors don't rust. I've never heard of this.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Right Front Window Would Barely Move When Opening It
My right front window would barely move when I was opening it. Binding real bad on the way down. So I pulled the door panel, ( a two minute affair ) lubed all the tracks with silicone grease. Now the window goes down very easily.
I had all four doors done in an hour. To remove the door panels, remove the red reflector from the door, remove the screw underneath of it. Gently pry up on the window switch bezel at the front for the front door, and the side for the rear doors if so equipped. There will be another screw underneath. Unplug the switch, remove the screw. Remove the trip piece from above the hinge area. Push up on the panel and it comes off.
I used that real thick silicone grease that you can get a plumbers supply for lubing faucet o-rings. It looks like double thick vaseline. Windows work like a dream now.
Ford 7.3L Power Stroke (1999-2003) :: Truck Constantly Bucked And Would Barely Reach 20 MPH
So I have had this occasional hiccup that has gotten more frequent. I figured since our weather has been extra cold (lows about 15 F, around 22 F in the morning), that the temperature had been contributing to the issue. My truck would hiccup and burp out some white smoke. At first it didn't throw a check engine or any codes. As of recently I would get a check engine light, but torque pro could not get any codes, they would be cleared when I cycled the key. Anyways, I finally got some codes yesterday because it happened again. The codes where P0603 and P0344.
So I ordered 2 new CPS from Riffraff yesterday (hoping that they will be here today so I can install one). Fast forward to this morning and i get the hiccup again except worse. Now my truck would barely reach 20mph and it constantly bucked. I limped my way to work (only 4 miles) and of course I got a check engine light but there were no codes that I could retrieve with Torque Pro again. I had read on another thread that the guy had an issue with a wire in the harness near the 42pin connector for the IDM. He replaced his CPS taped up the wire and it went away.
I'm at work and now I'm paranoid that I wont be able to make it home. Is there anything temporary I can do for the CPS, like maybe disconnect it and spray it with some contact cleaner, until I can replace it? I'm going to trace the wire harness to make sure there aren't any bare wires. I forgot to mention that the local stealership replaced the CPS for free due to recall less than 3000 miles ago...
Ford 7.3L Power Stroke (1999-2003) :: New HPOP And Injectors - Long Cranking About 15 - 30 Seconds
I recently did the following work:
New Injectors
New T500 Hpop
New IPR
New ICP Sensor
New UVCH/Glowplugs
New starter
Been cranking about 15-30 seconds each time about a dozen times now. I've pulled the icp and the hp crossover and have oil flowing at each.
ICP builds to about 240 psi and at a 98% duty cycle....so I assume there's still some air in the system. I"m not getting any sense that the engine is trying to hit. Do i just keep cranking?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F550 - Knock After Injectors Replaced
I just replaced all 8 injectors in my 01 F550 with remans from FFD. I have noticed a constant knock at idle but truck runs great. Blowby has no pressure behind it, truck does not smoke. Does this sound like a problem unrelated to an injector?
It did not make this noise before replacing the injectors
[URL] .....
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Not Turning Over After Injectors Replacement
So I replaced all the rings on my injectors . After putting them back in turned the engine over 5-7 times by hand with the glow plugs out. Then I turned it over with them out as well with the valve covers off. After than I installed everything back in. Now is my problem. I've turned it over 5 times and no luck. Not even on turn over. The oil light keeps coming on?? The indicator doesn't move up at all. It will go up and come down ? Is something wrong with the hpop? Should I keep cranking? Gotta to charge the batteries now..
2001 f250 7.3
Ford 7.3L Power Stroke (1999-2003) :: 2001 Excursion Will Run Barely For About 20 Seconds / Shudders Then Dies
2001 Ford Excursion 7.3 will run barely for about 20 sec. shudders, then dies. Bought new, driven 334K miles. Performed the usual fixes common to 7.3 issues over the years. All original injectors except for #7 which I replaced about 5 yrs ago. (I know should have replaced in sets but not in the budget at the time). Anyway had my wife turn the engine over after I had removed valve covers for inspection and observed a lot of smoke coming out of what appears to be at or around number 7 rocker arm valley? All rocker arm/pushrods look to be moving as they should beyond that I'm in over my head. Am I screwed or could it possibly just be a bad injector/injectors?
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - White Smoke - Injectors / Lack Of Compression
I have a 2001 7.3 with 243k. I think the injectors are shot but other people including a local mechanic say it's not the injectors. What the truck does is smoke white. Sometimes little puffs when accelerating. Sometimes clouds that make the people behind you drop back a 100 feet. I have a ts6 on the truck and that alone with the 243k miles is enough to think its bad injectors. It smoke white. The exhaust is moist to the touch with soot built up like crazy. It doesn't really smell sweet and it's not really blue at all. It's getting horrible mpg. And lacks power. I don't have a high enough psi gauge to test compression. All arrows pointing to injectors?
View 8 Replies