Ford 7.3L Power Stroke (1999-2003) :: Still White Grey Smoke After Replacement Of Rings On Injector?
I replaced the rings on all 8 injectors put in 8 new glow plugs and a relay. My truck is still putting out grey/ white smoke at start up. It goes away after about a minutes. Truck runs a little rough a first then smooths out. I know some smoke after doing a job like this is to be expected but I was thinking I t would go away by now. I've been running through my head what I might of done wrong but I can't think of anything.
Does it just need all new injectors and not just rings ?
2001 f250 7.3
Ford 6.0L Power Stroke Diesel :: Smokes White After 10 Minutes Warm Up - EGR?
My truck is puffing smoke after about 10 minutes and warmed up (looks white). It happens only one time for about 30 seconds and looks light grey or whitish in color, definitely not black smoke. The truck runs just fine, starts great, doesn't hesitate or studder, doesn't loose any coolant, no signs of pukage. In other words, it Runs perfect.
By the time the smoke happens I am usually at an intersection and see this white smoke billow past me or see it in the pass. side mirror. it's too hard at the time to get out of the truck at that exact 10-15 seconds it smokes to smell it or see it's true color without my sunglasses on but it looks white or greyish. not convinced it's a blueish color.
The truck doesn't smoke at start up or run rough so I'm ruling out injectors. I think it might be the egr cooler that is still connected eventhough there is no hot gasses going through it. (Did the up pipe mod). I might have an egr valve that has a bad seal on it. I'll have to remove the egr valve and see if it looks gummy in there since the egr cooler still routes coolant.
The other thing it might be is a bad oil seal on the turbo which is burning off leaked oil after it's warmed up, again I don't see it smoke for the rest of the day.
The very first time I saw it smoke was the day after I did the up pipe mod and capped off the egr cooler. I may have had a small cooler leak before I did the up pipe mod and now the coolant (if it's coolant) can't run in the exhaust or burn off there directly. My SCT turns off the egr valve but the valve may have a bad seal in it along with a defective egr cooler. will remove the valve to inspect tomorrow if possible.
Ford 6.0L Power Stroke Diesel :: 2005 - Bullet Proofed But Grey White Smoke
Just picked my 2005 excursion from being bulletproofed. Arp studs, oem head gaskets, turbo cleaned rebuilt, blue spring mod, 8 new Motorcraft injectors, rebuilt heads surfaced, new Ford oil cooler, egr plugged delete, sct x4 on 2nd tow tune, new radiator, new fan clutch, new water pump, and sinister delete kit. I got almost home to last stop sign and took off and noticed grey/white smoke.
Then drove so more for 20 minutes. Everything you come to complete stop and take off it does this. On start up it will puff a little puff then go away. Is this normal after a rebuild and go away after some miles have been put on engine. Or should I be worried. It runs awesome now and idles so smooth with tons of power on tow tune.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Grey Smoke Coming Out While Driving
I didn't notice anything until I was towing yesterday and tried to pass a car to get onto the offramp.
Anyway, I went to floor it so I could get around and, in my mirror, I could see a decent bit of grey smoke coming out. What could it be?
It doesn't smoke at all on startup and runs smooth right away.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Loud Knocking - Smoking Grey
I have a 02 power stroke 7.3, driving down the road the other day is started smoking a grayish white smoke pretty good. i let off the throttle and it had a real loud knock along with the smoke. oil pressure was good. i stuck it in neutral and revved it up kept smoking but the knock would go away at higher rpm. then all at once it would stop and run fine. then today it started doing it and wont stop now at all.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Misfire Code P1316 / Smokes Bad If Rev It
I have a 03 7.3 runs like crap. buzz test says cyl 2 and 4 have high to low side open. the only code that's hard is p1316. it also says cyl 1-3-4 fail balance test but not always some times only 2 fail.... I ohm tested injectors all the way to the idm and all are between 3.1 and 4.2 ish. So I guess I can rule out wiring. it smokes pretty bad if I rev it. it was running good till I parked it for 2 days. I did put HSS in oil 2 weeks ago to try clean out little rough acceleration. I did find my ipr nut fell off and spacer ipr was just floating around on the shaft I put that back together it was laying there.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Smokes While Driving Under Load And Shuddering At 2k RPMs
Ill start off with my mods and recent maintenance things I have done before fully describing the issue.
E99 7.3l with 190k on the clock
Full 5" turbo back
TS-6 chip
EGT, Boost and trans temp gauge
New ford glow plugs
Re-orings injectors
new valve cover gaskets
new fuel filter and fuel lines
new turbo with a ww2
Newer trans and oil pan
I think that should do it, now for my problem. The truck starts good cranks over once and is running with no hesitation, the engine run a little rough, more than normal vibration at idle almost like a small miss. No smoke at idle.
While driving with no/little load on the engine runs great , but under load there is a good amount of white smoke/ oil smell. The turbo is new and is not leaking oil I have already checked over that and the exhaust is new but there is some oil that is at the tail pipe in liquid form. The exhaust up pipe that goes to the turbo is not covered in oil either
The truck cruising in OD or in 3rd with O/D off around 2k rpms it shudders real bad almost like the truck is going to shake its self apart. but at like 2400 rpms and above its fine. Where is a good place to start the diagnosis as I am pretty new to the Diesel world. From what I've read it looks to be either rings are junk or maybe I have some bad injectors (thats what it feels like to me) but would that cause it to smoke like crazy?
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start / Smokes And Running Rough When Cold
I have a 01 7.3 crew cab dually and it's had cold start problems since i got it in 09.I have replaced everything i could think of including glow plugs gpr,harness and batteries. Any temp below 40 i have to plug it in . If i cycle it 3 or 4 times it will start but it smokes and runs ruff. My 00 7.3 excursion starts up down to about 10 degrees than i have to plug it in so i know dually is not right.
I have a afe intake,1.5 injectors, driven diesel rr, adrenilin pump,dp tune by gear head. Kinda at wits end don't mind plugging it in in dead of winter but now one night it's 30 next it's50 and i don't have to . Also have fully built trans by level 10 if it matters .I get battery light coming on every now and again. New alt about every year and a half.
Ford 7.3L Power Stroke (1999-2003) :: White Smoke Blowing / Smells Like Fuel And Loses All Power
I am a mechanic and tow operator running a late 99 f350 7.3 6 speed cab and chassis wrecker. This truck has had a hard life and has been neglected for quite some time, and now has become my baby/headache. Truck starts great, idles nice, and will run great for about 5 minutes until it starts billowing white smoke that smells like fuel and loses all power. If you continue to drive it it will die. Sounds like it's dropping cylinders and will barely idle. If you stop for 5 minutes or so and let it idle it will smooth back out and will run great again for another minute or two, then right back to stumbling.
Using torque app, hpop pressure looks good when it's running well. Peaks at 3k, IPR maintaining 30-40% max. As soon as it stumbles you can see the hpop drop to 5-600 and the IPR will climb to 65%. Let it idea bit and they go back to normal, and stay good until it stumbles again.
Ive changed the fuel pump, ICP,rebuilt FPR, change fuel filter, pulled and cleaned the fuel tank (metal tank, no delamination, looks perfect inside). Pickup screen looked good. Cleaned the IPR, cleaned the hpop reservoir, there was no screen inside. Checked voltage at fuel pump, 11.78 across the pump with it running. Pulled valve covers, no noticeable leaks around injectors. Injectors have less than 5k miles. Remans with 100% larger tips.
To me it seems like the lpop is not keeping up with the hpop under load, starving it until you idle and let it catch up. Could it still be bad injector orings? Bad lpop? Something I'm not thinking of?
Ford 7.3L Power Stroke (1999-2003) :: White Smoke / Clicking Noise And Steadily Losing Power
I have a 7.3 Excursion, 234K Miles, 4R100 Transmission. Today I was in a rush to take one of our dogs to the vet, when I hit overdrive going up a hill, it almost sounded like a clicking noise and I was steadily losing power. I came to a stop sign and put it in park and it started to develop a constant lope that was rough. Whenever I would step on the gas it would put out white smoke which it has never done before. I was able to take it a couple miles before it did the same thing except this time it shut itself off.
Recently I have been having transmission issues as it feels im losing first gear. A while back I noticed it would idle slightly in park every now and then. A couple days before this happened, I came to a stop and my truck started loping slightly and first gear IN DRIVE felt very very weak. I have recently replaced the cam position sensor as well as the ICP sensor. I'm at a loss, I plan to do a ZF6 transmission swap very soon and this is only making me panic even more.
I never dog the truck, take it mudding, etc. Oil is changed every 3-4,000 miles. I did however get it scanned a while back and I believe two codes came up for two pistons, also did an injector buzz test and they all sounded strong.
Ford 7.3L Power Stroke (1999-2003) :: Missing At Idle - Power Loss At 50 MPH - White Smoke From Tailpipe
My 02 excursion is missing at idle and jars the whole truck around going approx 50mph feels like good amount of power loss but still pushing 30psi boost, just got autoenginuity all injectors buzz fine on the test, contribution test show balance fault in cylinders 1&8, should I look for o-rings to be bad, uvch, cups cracked or what ----- turbo fine, hpop great condition, new IPR, new fuel pump and hutch mod, about. 250k miles on truck nothing else major showed up on ae.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke Only When Barely On The Gas?
My 2001 7.3 is smoking only when barely on the gas. New fuel filter. Don't know if its possible injector going bad or what? Smoke is white not black.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Blowing White Smoke - Low Power - Rattling Noise From Engine - Broke Down?
Moving my worldly goods from California to Oklahoma in a rented 26' box truck with my wife following in our '02 F350 loaded to the gills with my lathe, mill, air compressor, weld and assorted machinery. Just west of Deming NM it started to blow lots of white smoke and down on power. Some rattling noises from the engine when throttled up & won't reach 3000RPM.
Had it towed to an impound yard for storage. Plan on sending a flat bed to pick it up when we get to Tulsa.
Any experience with a tilt back trailer capable of loading & transporting this truck that weighs around 17,000 pounds? My plan is to continue on to Tulsa & make arrangements from there.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F450 - SES Light Came On Followed By Loss Of Power Under Load And White Smoke From Exhaust
I have a 2001 F450 7.3 chassis cab with just over 100k. I have a new problem... So far on two different occasions the service engine came on followed by a loss of power under a load and white smoke from the exhaust. Took it to the shop the first time, they determined it to be a dirty air filter, which seemed odd since it just happened all of a sudden. They changed air & fuel filter, problem gone- for two weeks..
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke At Idle When Warm
I have a Tymar intake, magnaflow exhaust, a DP Tuner and I have Rosewood Diesel injectors.
I had a bad oil leak recently and it seemed to be coming from the turbo area so I changed all the o rings back there and deleted the EBPV system (I cut out the butterfly and welded the holes shut, cut the part of the pedestal that held the actuator because it looked like it was leaking and welded the oil holes in the pedestal that fed it. I left the actual EBPV sender in the pedestal and kept it connected to the harness)
After all that was done I checked the oil and it was low but still on the dipstick so I drove it to the local parts place to get some more oil, about 2 miles, because I wanted to check for leaks. It was not happy, ICP low code came up it was sputtering and jerking when stopped at a light. I got to the store and parked it, it took about 3 litres of oil and seemed to run pretty good after that.
But on the way home I noticed a bunch of white smoke, I figured maybe an injector was stuck. I started it a little later and no white smoke in the driveway so I thought maybe it had gotten lubed enough and had sorted itself out. That was a few days ago.
Today I started it and let it idle in the driveway for about 15 mins and no white smoke, I wanted to get it up to speed a little so I took it to do an errand that was about 10 miles away, lots of lights and a bit of highway. It would run fine while going at speed but as I would slow down for a light the ICP would go down to around 600psi and the white smoke would start, as sitting idling a huge cloud of white smoke would form (yes, I was that guy), once I could take off and get it running a bit harder it would go away again.
I am assuming that I have a stuck injector (or cracked), I have no oil in my degas bottle and it doesn't look like it is fuller than before. Seems like I may have used more fuel than I should have, but pretty hard to tell just from the fuel gauge.
I have tried a buzz test and they all sound the same, tried a Compression Contribution test, no codes from that.
How can I locate a stuck injector? If that's what it is?
Ford 7.3L Power Stroke (1999-2003) :: White Smoke At Startup Even When Its 90 Degrees Out
I have long been having troubles with white smoke at startup, even when its 90 degrees out. Long story short I've got new glowplugs, GPR, UVCHs, valve cover gaskets, injectors, turbo, valve seals, valve springs, and HPOP all within the last year. Most of those parts were needed, some maybe not so much. After installing injectors things started getting worse, whether they're related or not I'm not sure yet. I pulled passenger side valve cover off again in an attempt to figure something out and heard this coming out of the intake spider.
[URL].....
The strange thing is it goes away when it warms up. I should also note the reason I started with the passenger side is because I did a compression test and this side had the lowest readings, with #5 being 270 psi. I disconnected each injector one at a time on the passenger side to see if it made a difference while running but didn't really notice a difference. Am I looking at a motor rebuild, or at the very least a head removal?
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Smoke White Randomly?
my 2000 f350 7.3 is acting strange lately. Its got 252k and is all stock other than exhaust,intake,ww2. It smokes white every random once in a while for some reason. At start up it wont though. If i get on it every once in a while it will smoke white then go to back to black. Im not consuming coolant, and the oil looks fine, no residue on the oil cap and its not puffing out the oil cap either. Other than that its running great just dont know why it goes white every so often.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke / SES Light Comes On When Accelerate
When my 99.5 SD is cold ( 50-60 f) it smokes a lot of white horrible smelling smoke for the first 2-4 minutes. If plugged in the block heater it doesn't do it. Also when cold, when you accelerate the SES light comes on until you let off on the throttle then it goes off. Even going 10mph in low rpm? Once engine is up to temp it doesn't do it anymore. It seems to run fine otherwise. I do have 2, 700 CCA Napa batteries that are from 2011 which I plan on replacing next month with Motorcraft Maxx 850 CCA.
I have replaced the UVCH, CPS, Fresh Oil and put additives in my fuel. I have even disconnected my DP Tuner F5 and it still does it. I have AE with ford bundle and it seems like my HPOP seems to be working fine as well as buzz test and glow plug. Could it be an injector ( I have stage1 casserly from full force)? What about a sensor not working? It has always smoked since I have had it ( about 3 years) but the SES light issue has only been happening since my IDM was replaced and I had a mechanic work on it.
Ford 7.3L Power Stroke (1999-2003) :: Tough To Start And A Lot Of White Smoke
For the past few days I noticed my truck would be really rough to start and a lot of white smoke. but once it ran for a minute or less it would be fine. Today when I got home I popped the hood and was looking for anything and noticed my degas bottle had this weird fluid inside on top of the coolant? So I popped the cap off and smelt it and its fuel. Of course this would happen to me. Now I'm not going to lie I have beat on it a few times this week but nothing so so serious.
Could this be contributing to it? Could it be a head gasket? now being a diesel mechanic I doubt its a head gasket simply because there is no oil mixing. I am praying its nothing too major. Once I have the narrowed down to what it could be ill see if its something I could tackle or if the stealership has to do it, which I am not looking forward to. I'd rather be down a truck for a little bit and save a boat load of cash.