Ford 7.3L Power Stroke (1999-2003) :: Engine Quits Running Randomly?
My engine suddenly stops while driving. There is no warning or loss of power, it just stops randomly after running fine for a while. After some time (might be minutes or hours) the engine turns on and runs fine.
I have no clue what it might be, I believe it might be an electrical problem affecting the diesel pump. The pump has a pair of cables coming in to a white plug at the pump's back, I disconnected them but the engine still runs.
Ford 7.3L Power Stroke (1999-2003) :: Engine Cut Off While Running And Stopped Just Like Turned The Key Off
While stopped, engine running, in D, the engine cut off just like I turned the key off. I sat there for about thirty minutes and on the 7th or 8th try, the engine finally started. I drove it back to camp and thinking it might be the CPS, I swapped it out. Unfortunately it must be something else because I can't get it started anymore.
ICP and IPR are fairly new, but I unplugged the ICP and tried to start it anyway. It didn't choke out (like it was a fuel issue) but I checked the fuel bowl anyway and the pressure builds fine. I got it restarted once, so it can't be a fuse but I checked them all anyway.
Oil pressure builds to 780+ when cranking. Batteries still have plenty of cranking juice and without my AE, I'm frustrated beyond belief.
Ford 7.3L Power Stroke (1999-2003) :: Oil Leak Alarming Rate Only When Engine Is Running
So I decided to start the year with fresh oil. Like the hundreds of oil changes before, i changed the filter and added new oil. Only this time, oil started to drip off the bottom of the Oil filter at an alarming rate, only when the engine was running.
I figured the filter didn't seal well, so I repeated the oil change process. nothing changed, still leaking.
It was really cold (-10 C) when I did the oil change, I mention this in case it is a contributing consideration.
My truck is a 2000.
Ford 7.3L Power Stroke (1999-2003) :: Engine Stopped Running Suddenly - Dash Went Blank?
I was driving from my house the other day when the engine suddenly cut out and the dash went blank. there was no warning, it was like someone pulled the plug.
-When I turn the key to the first position (Acc) all the accessories work as normal. the lights, radio, windows, ect all work like normal.
-When I turn the key to the second position (run) nothing changes. no gauges, no dash lights, warning lights, and no (wait to start) squiggly line. only thing I hear is the high pressure pump on the engine cycle.
In the third position (start) the truck will turn over but will not start.
Ford 7.3L Power Stroke (1999-2003) :: Engine Running Sound / Rear Axle Locked Up
Well, get the engine running sound, then the drivetrain takes a crap on me. . . On my way home, about 60mph. Hear a noise from front drivers side. Gets to the point where I think I am losing a tire. Got out and checked the lugs, all clear. Got back in and the truck wouldn't move. Shifted thru all the gears, nothing.
Revved up to 1500rpm and it just sits there and shakes, like it wants to go but can't. No grinding or anything. Got a tow truck and as we were loading it, noticed that the front axle was rolling fine, but the rear was dragging. Tried it in N and D and it still wasn't rolling. Also observed drips on the flatbed and the drain plug on the transfer case was wet.
Praying that it is transmission, cuz I can just have them come get it and have it repaired under warranty. Heck its only got about 3500 miles on it. If its the hat to check? Ill be spending the rest of my evening on YT/Google. . . (Figured this was the right area to post this, cuz its a 99 7.3, I didn't see a dedicated drivetrain area so. . . )
Ford 7.3L Power Stroke (1999-2003) :: Injectors Clacking / Engine Feels Like Running Out Of Fuel
Engine felt like it was running out fuel, injectors were clacking. I got home put on AE and it has a low high open on the code reading. took valve cover off and plug came out. I did the quarter modification.
Anyway took the truck out a few days later truck drove ok when cold then after about an hour it lost power again and started clacking until it died out. I had to stop and let it cool off about 10 times before i made it home. I changed ICP sensor. took it out for ride and about ten minutes later same thing. I have to let oil temp get down to 165 before i can drive it again.
When i first drive it Icp pressure is about 500 at idle and 2650 at full throttle, that is until it starts clacking again and losing power then the engine wont take any throttle..and ICP duty cycle is at 26%... Would bad IPR do this??
Ford 7.3L Power Stroke (1999-2003) :: Door Ajar Light Stays On All The Time When Engine Is Running
Here are some signs of the problem.
*Key fob does not work - battery is good.
*Interior overhead light works only on manual.
*Driver's auto door lock (with driver door open) will lock all four doors but the driver's door will automatically open back. To secure the truck I manually lock the driver's door.
*I replaced the driver's door 'ajar switch' with no results. The old switch was good after testing - normally closed until the ball is depressed then it goes to open.
*No codes.
*I just checked all the mini-fuses with a VOM and they are good.
*Could one of the relays be part of the problem?
I am curious if there is a scanner that can identify the bad door ajar switch if any?
From what I have read so far it appears the VSM (Vehicle Security Module) may be bad as a many of these 2002's complain of this problem and the VSM generally solves the issues. Are there folks other than the dealerships that can program the module if I purchase a new one and remove the old OEM one? Other than the inconvenience the truck runs fine other wise.
Ford 7.3L Power Stroke (1999-2003) :: Vibrations On The Floor Board
Okay I'm also having issues with vibrations on the floor board. I replaced the carrier bearing last week and not sure if correctly done or maybe I didn't get the splines in the exact order they came out in but the vibration is still there if not worse. I was thinking I could order a new rear drive shaft for around 350.00? would it matter how it was installed?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Hesitate For A Minute And Then Lag When Floor It Going Uphill
I have a 2000 7.3 and I have a hypertech Max Energy Programmer set to stage 3 in my truck right now (100 HP). I noticed last night when I was going up hill and had my foot to the floor the truck would hesitate for a minute and then lag before it was would catch up to itself. I did it again on some flat ground and noticed when it did do that my boost gauge would get to 20 and then fall to Zero. If I start out and gradually get to the floor without punching it the truck drive fine. How to fix it?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: When Push The Clutch To Floor Its Not Disengaging All The Way
In my 99 with a zf6 it seems like when I push the clutch to the floor it's not disengaging all the way. It has a newer valair clutch in it maybe 15000 miles on it. It's really hard to get the truck in reverse or first from a stop. If the truck is stopped and it's in reverse or first with the clutch to the floor it will move in that gear. Is there a adjustment on the clutch? I'm thinking no since its hydraulic....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Clutch Pedal Would Squeak While Coming Off The Floor?
What is failing. I have a 2000 F350 PSD with 116k miles. When I bought the truck last year, I noticed that the clutch pedal would squeak while it was coming off the floor. It doesn't happen when the engine is cold. I need to drive it about 30 min before it starts to happen. On longer trips, several hours, the squeaking is louder and the pedal gets very stiff. When I stop for fuel, I've come close to stalling when coming out of 1st gear. I can push the pedal to the floor, but on the way up, the pedal squeaks, and then once I reach a certain point, say 3-4 inches off the floor, the pedal looses all freeplay. The best way for me to describe it is the pedal travels up faster than it normally does when it's cold, and if I don't compensate with more throttle at that point, it will stall.
I've learned a lot by reading this forum for the past year, but I don't know the first thing about how to diagnose problems like this. I've taken it to 2 mechanics for test rides -- one thinks the clutch is fine and thinks the problem is the slave cylinder or a broken bushing in the pedal.
The other shop is also a small independent shop, but they specialize exclusively in Ford trucks, so I thought they would be more knowledgeable. But now I'm wondering if they could sense my ignorance and are taking advantage of the situation. They also took it for a drive, but they think the slave cylinder is fine and that the clutch needs to be replaced. I questioned him about the slave, and he pulled it to look at it, and asked me to push the pedal slowly while he was under the truck. I still had a little resistance and a faint squeak even in this situation. But he said the hydraulics are so simple that he felt we could rule that out. I can't remember exactly what he said, but I think he believes one of the springs in the clutch plate has failed. I just know they are suggesting a new clutch and they want to machine the flywheel to original specs.
I thought the leading symptom of a failing clutch was slippage under a load. So under strain, I would expect my engine to race occasionally, like I'm in neutral. But I've NEVER experienced anything remotely like this, even when driving hard in the hills pulling my travel trailer.
I know something is wrong, but based on my limited knowledge, I'm not sure what. It's getting a little harder for me to move the shifter into 1st and reverse, but once it's there it's fine. I've never experienced any racing or slippage in any gear. The one definite symptom I have is that squeaky pedal that when driven for a couple of hours, gets so stiff that it can cause near stall outs. With those symptoms, what do you think is going wrong?
Ford 7.3L Power Stroke (1999-2003) :: Thumping Sound Under Driver Side Floor Board
I have not had much fun with the front end of my 1999 4x4 7.3 diesel dually. Well I replaced the ball joints with moogs over the winter. Just recently I my truck has developed a thumping sound that I can feel under my driver side floor board. The weird thing is that it does not do it all the time. But yesterday I noticed it for a more extended amount of time.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Floor And Defrost Work But Dash Vents Not Working
The floor and defrost vents work. It just stays on defrost when you try to use the dash vents. The actuator seems to be working fine. I can watch the arm move through all the motions. and I cant find ANY vacuum leaks. Yes I looked at the hubs and under the hood. May be moving to alaska and kind of need my heater to work properly. . . .
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Brakes Lose Pressure Entirely And Pedal Goes To The Floor When Hit Bumps
The problem occurs when you hit bumps while braking, or if you get on the brakes to hard. It seems like the brakes lose pressure entirely and the pedal goes to the floor. It kicks back in when the ground smooths out, or if you are braking hard it slowly grabs again. At first i thought it was sliding, but it definitely is not. The truck appeared to be equipped with abs but the previous owner seems to have cut the abs wire/sensor at the hub. Another thought i had is maybe the brakes need to be bled and have fresh fluid put in them, I have not tried this yet (Plan to this weekend along with a dozen other things). Its rather scary when it happens. but i didnt think much of it until i nearly rear ended someone..with my younger brother in the car. Now i need to fix this asap.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Clutch Pedal Goes 1/3 Of Way Down - Drops To Floor And Stay?
I just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Transmission Fluid On The Floor / Hissing Sound When Cut It Off
I have a 2000 F250 4x4, it has been sitting in my garage for about 3 weeks. I cranked it up and backed it up about 10'. A few hours later I noticed a lot of transmission fluid on the floor. I remember hearing a hissing sound when I cut it off but didn't think anything about it. The fluid is on passengers side of truck, right side of the engine. Most of fluid is toward the rear but some ran down in front of the axle also. It's up high also, I've got fluid on rear of valve cover. I've cranked it up and let it run but can't get it to leak. Where did all this fluid come from?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 F350 - Oil Leak When Parked After Running
I have a 03 F-350, 7.3L. There is a slow oil leak that only leaks after I've run the truck. In other words, it doesn't just sit and leak overnight. I'll park it after running, and the next morning I'll notice a small pool of oil, approximately 2" in diameter. The leak appears to be coming from the oil pan area. I degreased the entire oil pan area to get a better visual of where the leak is coming from. I can see oil trailing down the front of the oil pan and the rear of the oil pan. Does this sound like the gasket? Or, what else could it be? I'm praying its not as bad as I think and need to replace the gasket.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Loss Of Power / Rough Running
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.