Ford 7.3L Power Stroke (1999-2003) :: Low Boost / Black Smoke
Bought the x in feb, put in the billeted wheel, modified the turbo pedestal, put in dorman uppies, put my boost leak detector on it and had no leaks then. Also put on the walker btm and gauges at that point. Took my chip to a local to get tunes. I was pleased enough with the power, and can hit 24 psi. However, it smokes like a freight train if I give it much pedal. I don't drive it a ton, but in the last week I did a 400 mile trip to pick up a trailer, then 800 miles on vacation in Colorado. The fender flare by the exhaust is now black.
It has to be pulling a trailer or going up a decent hill while cruising at 70 to show any boost at all on the gauge. If I give it gas, it belches out the smoke, unless I get on it and get the boost to 10 or more. Most of the time while cruising along I don't need to speed up that much so it just smokes and doesn't build more than 2 psi boost.
My f350 by comparison usually runs 4-6 psi boost running down the road at 65, and slight movements of the accelerator can affect that number immediately.
I don't have my leak detector with me so I can't verify that I have no leaks right now, but I can still hit 24 psi... Last night I used oven cleaner and got the whole area around the turbo pretty clean. Drove it 60 miles today, and don't see any soot around anything, maybe it's to soon to tell? Is there anything else I should check, or is it as simple as getting new tunes?
Ford 7.3L Power Stroke (1999-2003) :: Black Smoke - Little Power - No Boost Until 2500 Rpm?
Short version is that I just did the EBPV delete with new pedestal and turbo exhaust outlet and put a new turbo middle cartridge in as mine had blown a seal and possibly broken the shaft. Once I got it all put together, I took it for a test drive and it was building 20PSI like it used to but I didn't have the accumulator and turbo mated up fully so I had a leak there.
I corrected that and now don't get any boost until I get to about 2500RPM and then it only builds to about 10PSI. I've double and triple checked all my connections, boots, etc. and everything is tight on the intake, intercooler, up-pipes and collector, exhaust and the spider, I can't see or feel any problems there. I tried disconnecting the MAP sensor and it might be a little better but not even close to normal.
Tried disconnecting the red line from the wastegate and plugging it with no difference. I'm stuck, and frustrated. I do have AE, watching the MGP looks like the MAP sensor is working. I feel like I'm overlooking something simple but I just can't figure out what it is...
Ford 7.3L Power Stroke (1999-2003) :: Low On Power / Injectors HPOP Or Tune?
So I have a 2002 7.3 Excursion and I think it is low on power. ICP is falling on its face when on a 60 or 80 HP tune. I have some boost leaks at the plenums and will work on that but that shouldn't cause my ICP to tank at full throttle. Following are some numbers I pulled with WOT runs up a 6% grade.
16PSI BOOST
EXHAUST PRESSURE 40
ICP 1900
80%IPRDC
this is with the 60 or 80HP tune on my DP-tuner. If I ease into the throttle I get
2700 ICP with
45%IPRDC
but if I stomp on the throttle it stumbles and ICP tanks.
Running the stock tune I can maintain
2700ICP at
40-45%IPRDC
Is this my HPOP being weak, or worn out injectors, to much of a tune or a combo of all three?
Ford 7.3L Power Stroke (1999-2003) :: Chip Or Tune Increase MPGs?
My f350 has 300k on it. 95% of its driving is on trips of 22 miles or more at highway speeds. Occasionally long trips (going to put on 3k miles in 8 days here soon)
Want to drive the truck to 500k miles...but wondering if a tune or a chip would change the mpgs and not hurt reliability? I know its not a Honda Civic...I am not looking for 35mpg....would love to pick up a couple more than I have.
Ford 7.3L Power Stroke (1999-2003) :: Trans Slipping On 25hp Tune Up High In RPM Band And Shutters When Up Shifting
My excursion's trans is slipping on the 25hp tune up high in the RPM band and shutters when up shifting. I have dropped to stock most of the time, but I know i am on borrowed time.
I had a JW trans in my e99, and there is no question on the durability and performance of the transmission. The price has gone up a lot, but that's maybe not the big issue.
I live in the mountains and spend a lot of time pulling and just driving in that 40 to 60 mph range over mountain passes. That is basically where I spend ALL of my time.
The distance between 3rd and 4th is driving me CRAZY! I have researched everything from swapping to a manual, to PCS controllers, to trying 4.11 gears, to overdrive units.
Swapping Manual: ZF6 is the obvious candidate, but I have read the swap is not probably something I have the skills or tools to do. I have also read that the performance of the ZF6 is sub par. But it seems like it would give me my 3.5 gear that I am looking for.
PCS Controller: Looks cool for a way to have control besides using the tree shift. Maybe a compromise on not swapping in a manual.
4.11 Gears: I get pretty excited thinking about the low end torque etc. I go off road almost every week, and like I said, I hardly go over 75 mph. But once in a while I do. Right now, the truck turns about 2300- 2500 rpm at interstate cruising speed. Looking for 4.10s rpm in that range to compare? Also, how bad of a fuel economy hit would I take? What is the cruising rpm of 4.10's between 60 and 65 mph, or in general what is the rpm change?
Overdrive Unit: I have always been interested in more gears, but I read about someone who installed one behind a 7.3 and didn't have they great of results. To the point where he said it wasn't worth it.
Ford 7.3L Power Stroke (1999-2003) :: Boost Leak When Hit 24.5 Psi?
This was briefly discussed as part of another thread. It appears that I have a boost leak when I hit roughly 24.5 psi. The leak seems to stay for a few minutes after showing itself, but then I'm able to produce boosts up to 24.5 again. For example, on my 20-mile/30-minute drive to work, I can make this leak "appear" four or five times, maybe more if I try. Does this self-healing leak ring a bell? I haven't done a boost leak test yet, but I'm leaning towards the RTV sealant at the OEM plenums due to the self-healing attribute.
To add a little info to this thread, I recently installed an S&B intake, 4" exhaust, bellowed up-pipes, RR billet wheel, RR CAC intercooler boot kit with new clamps, RDP reinforcing plenum inserts, AIH delete plug, and I removed the wastegate solenoid along with the red and green tubes. I don't have any gauges, but I recently began monitoring the boost using FORScan. Before all of this, I don't think I was producing enough boost to cause this leak, and I had no way to monitor for this leak.
Ford 7.3L Power Stroke (1999-2003) :: Rebuilt Turbo Still No Power And No Boost?
Well I am at a loss now. Rebuilt the turbo with a new wheel and kit from Riffraff. I still have no power, no boost and no codes. The new wheel whistles. I can hear it. It sounds way better than the old one. But still no power. I really don't know what to do now.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - No Boost And Smoke - No Power At All?
I have a 2006 f350 4x4 dually 6.0. The other morning when leaving for work I hard a loud air noise, like a jet. It only happens when the motor is trying to create boost. I have NO boost. No smoke. If I push the fuel pedal past 1/4, nothing. Its like its stuck and no more power at all. I have changed the boot from the turbo to the intercooler pipe. (looked like it had cracks in it). Checked the cold pipe, no cracks seen. Check the exhaust clamps, into the turbo, they are tight. The turbo is seeping oil around the seal. I took the inlet, fresh air, pipe off. Check the turbo spool for looseness, fins, spun the wheel, ran the engine and watch to wheel. Seen no issues. Where to go now?? No coolant leaks, no oil leaks.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Code P1249 - Boost At About 20 PSI
I disconnected the red wastegate hose in order to address a low boost high EGT issue. This seemed to fix the boost / EGT issue for the most part, but now I get this P1249 code. The first time I got it I saw boost at about 20 PSI. I figured I would try to keep the boost below 20 in an attempt to prevent the code.
I managed to capture some log info when throwing the code. The highest boost reading I saw was 19.58. Pretty close to twenty but I question if I even should be getting this code at this level of boost?
Here's a chart with the boost info. Yes I still have a very bouncy EBP and hope to track that down at some point as well....
Ford 7.3L Power Stroke (1999-2003) :: Boost Tops Out At 29 - 30 Psi And 1 - 3 Down The Interstate
I believe I am having spooling issues with my 2000 f250 7.3 automatic truck. I now am running a 67mm billet compressor wheel with a 1.00ar turbine housing and high flow outlet so basically a thrust bearing 38r . I'm running oem sticks and PHP tunes on my hydra. On the 140 tune egts top out at 1200* uphill. So egts are not a problem. Boost tops out at 29-30 psi and 1-3 down the interstate. I see a lot of trucks that can hit 20+ psi in second by just squashing the skinny petal and I could also do this with my oem turbo. Mine takes awhile to get psi up like I said it will hit 30 if I'm petal to the carpet for a few and get going but I feel like it's not spooling as quickly as it "should ".
I completely built this turbo with new parts nothing was reused down to the heat shield behind the turbine wheel inside the turbine housing. I used all American And Canadian built parts . 360 thrust and a banks 1.00 turbine housing. When I bought the turbine shaft and compressor wheel it stated that they where pre balanced and I could clearly see the balancing marks on both but the shaft and compressor wheel are from two different manufacturers so there was no way to be sure that everything would align and be balanced. Basically my question is do you think it would to be wise to have the assembly balanced? Could this be the reason the turbo doesn't spool as fast as my oem gtp38 did . I've been running the turbo for four months now .
Ford 6.0L Power Stroke Diesel :: White Smoke And Minimal Boost
Ok, took the sub for a spin around the block yesterday. Turbo was singing a tune when I left. white smoke and minimal boost on the way back. It is spinning, just not boosting very well. Stuck? Electrical problem? any pointers, or easy stuff yo check, before pulling the pump?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Erratic Boost And Occasional Stalling?
I've had this 01 7.3 for a few months now. When I first purchased I dropped new battery's, couple glow plugs, and wire harness going to the Pass side valve cover. it has 150k on it and an Edge tunner.
My first problem was about 2 weeks ago, it was raining and i was making a turn at about 5mph And all power shut off. I put it into park cranked 3times started up and the tuner stayed off for about 3minutes. I ran to auto zone and picked up a cps (I've recently found that oem is the only way to go?)
I made a trip about 2hrs locked the CC in about 70mph and the boost was going well over 12psi. this seems crazy because i usually dont get it over 4psi. I drive it with a light foot. on my way home i was pulling a trailer about 8000lbs load driving about 5mph out of the lot it shut off again. Started right back up and made the trip home fine. With the exception of the erratic boost.
Yesterday it shut off at about 40mph and turned back on its own. I am not throwing out a lot smoke doesn't have problems starting, I did a once over on the wire harness's and nothings jumping out to me.
Ford 7.3L Power Stroke (1999-2003) :: Boost Leak Through Valve Covers?
So I just put billowed up pipes and changed the broken O ring in the turbo housing. Put everything back together and checked for a boost leak with the home made tester. Boots and everything ARE OK. I can hear air escaping from what seems to be the valve cover or intake. I realize that I am charging my crank case as well but it still concerns me that air is escaping from somewhere besides the CCV. I read the following forum and this guy had the same issue and after he found out he was charging his crank case he was no longer worried. . . . .
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Typical Boost Pressure / Mostly 0 Unless Under Acceleration
I just recently installed a CTS2 Insight and wondering what the typical boost pressures I should be seeing without a load just normal driving. Right now I am seeing mostly 0 unless under acceleration then it goes up to 10 psi if I floor it I am getting 15psi.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Intermittent 0 Boost After Short Drive
I guess it would be classified as very intermittent but in the past year I have had 3 separate times when my truck has after a short drive suddenly had zero boost..
Pull over and turn it off for 30 sec or so and all is fine. Cycle the ignition faster than that and issue persisted. It has only happened in colder temps. In all the reading I have done on FTE I've not come across anything similar.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - High Oil Consumption - Low Boost
Alrighty let me see if I can get everything. 01 6speed 450hp at rear wheels. Comp 910 valve springs, valve seals, 238-80% injectors, full RR, 38r turbo, napa air filter, Hydra with Gearhead tunes, 5"exhaust, 280k about 100k on rebuild. All mods done 40k ago. Now I have a horrible up pipe leak I assume is causing the low boost #'s I have to do another clutch so up pipes will be fixed when tranny is out this week. But I'm using 1-2 gallons of oil every 3k or so. I smell burning oil when I get out, mainly if I am getting on it then stop. I haven't pulled the fuel filter to see if its a injector o ring. (Tonight's project) but turbo sounds fine, I'm going check for shaft play tonight. What could be my loss of oil without it actually leaking on the ground?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Turbo Chatter Under Load - Boost Was Around 17 - 18 Psi
I have done some searching on this, seen a video on YouTube but haven't read anything that is firm on what it is. We pulled our 5er for the first time last weekend and the chatter was pretty pronounced in the Arbuckles here in OK. I was running around 65 mph when I hit the largest hill and as I was climbing my speed naturally dropped, boost was around 17 - 18 psi when the chatter started.
Is it something to be really concerned about? Is there anything to be done to prevent it? I'm pretty much still stock, only deletes have been airbox to 6637, and I deleted the heater by turbo for the boost gauge. Other than that everything on truck is still stock.
Ford 6.0L Power Stroke Diesel :: Low Power Before Boost Kicks In / Idling Rough With Blueish White Smoke Coming Out Of Exhaust
I just looked back and it has been since July 7th that my girl has been sitting in my shop. Well this past weekend I finally got her back together and started. It took a while to build pressure but she finally came to life..
While I am thrilled that she is running again i have low power before the boost kicks in and is idling rough with a blueish- white smoke coming out of the exhaust. Once i kick her a little she will get up and go but I've never had the smoke before.
I'm thinking maybe a bad injector???
Ford 7.3L Power Stroke (1999-2003) :: F350 - EBP Delete / Truck Won't Make More Than 3 PSI Of Boost
I bought a 99 f350 truck. it has a van turbo and exhaust back pressure delete. The truck wont make more than 3 PSI of boost. Ive got a p1690 wastegate actuator circuit code. unplugging the waste actuator does nothing. With the van turbo, is the actuator required? Is this code stopping the ecu from fueling and creating boost? I did a cylinder balance test, and cylinder 8 failed. Is a single injector not quite balanced enough to make it not boost past 3 psi? The turbo appears brand new (previous owner said it was), charge pipes hold pressure (tested), EBP Sensor tube is clean (shows up to 24 psi). I tested the wastegate actuator, OnDemand5 says if its over 50 ohms, its bad and replace it. its 69.5 ohms. Again, i dont want to replace it if i dont have to, as its not being used (no wastegate on van turbo), but if the ecu is preventing it from spooling because of the solenoid, ill change it.
View 14 Replies