Ford 7.3L Power Stroke (1999-2003) :: Losing Power At 2000 RPM Going About 65 - 70 MPH
I have a 1999 7.3 with 260k miles. It is all stock with the exception of straight pipe. I got the truck about 8 months ago and have put about 5k miles on it. Have never had any issues with it. I was driving from Dallas to Houston and about 45 minutes into the trip my truck lost power. I was going about 65-70 mph and the service engine line came on and I lost power. It was running rough and was blowing white smoke. I let it sit for a couple minutes and started it back up and ran fine until 30 minutes later. It did this 2 more times on the way to Houston. Oil is good, coolant is good. Not over heating. Threw a code the first time but didn't throw it the other times. I brought it to a mechanic and he thinks it's the Wastegate.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Running But Losing All Power
Where I should start? My 7.3 is running but losing all power. Pumping the fuel pedle will get it started and it will run for a few then lose everything again. Should i just drop the tank and check the sending unit and intake and filters first then work my way up?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Started Losing Power Then Slowly Die / Fuel Pump Bad?
I was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 Truck Losing Power / Service Engine Light Came On
Truck started losing power then service engine light came on, drove about another mile then it just stalled ( almost home lees than a 1/4 mile). Got out open hood oil everywhere on top of motor. Looked under truck and oil all over the road. Looked back where I was driving a line of oil as far an I could see. Checked oil barely any on stick. Where should I start hpop or plug?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke / Clicking Noise And Steadily Losing Power
I have a 7.3 Excursion, 234K Miles, 4R100 Transmission. Today I was in a rush to take one of our dogs to the vet, when I hit overdrive going up a hill, it almost sounded like a clicking noise and I was steadily losing power. I came to a stop sign and put it in park and it started to develop a constant lope that was rough. Whenever I would step on the gas it would put out white smoke which it has never done before. I was able to take it a couple miles before it did the same thing except this time it shut itself off.
Recently I have been having transmission issues as it feels im losing first gear. A while back I noticed it would idle slightly in park every now and then. A couple days before this happened, I came to a stop and my truck started loping slightly and first gear IN DRIVE felt very very weak. I have recently replaced the cam position sensor as well as the ICP sensor. I'm at a loss, I plan to do a ZF6 transmission swap very soon and this is only making me panic even more.
I never dog the truck, take it mudding, etc. Oil is changed every 3-4,000 miles. I did however get it scanned a while back and I believe two codes came up for two pistons, also did an injector buzz test and they all sounded strong.
Ford 7.3L Power Stroke (1999-2003) :: CEL On - Long Crank / Truck Starts Losing Power And Eventually Died
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
Ford 6.0L Power Stroke Diesel :: White Smoke / Steam Blowing And Losing Coolant
My 2006 6.0 is blowing white smoke/steam and Im losing coolant (not out the top). Pulled the EGR valve and its wet down there. All signs lead to EGR cooler? I've been reading a lot on this forum and Ill do the oil cooler at the same time. I seems VERY important to flush the coolant system before I tear into this. I am afraid of hydro locking the motor or ruining the head gasket or stretching the head studs if I run the truck. How can I do this without further damaging the engine? I am doing this myself. I'll have 3 solid days to finish this job because I have to tow my trailer in 5 days.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Losing Coolant / Radiator Making A Sloshing / Gurgling Noise
I have a 2003 6.0l... When I first bought truck, seemed to run fine. Since then truck has broke down on me once. I took it on a six hour drive, and couldn't turn vehicle off, because if so, truck wouldn't start back up until cool. After getting to my destination, fans seemed very loud every time I pressed pedal, and seemed very sluggish. Drove it a couple days and boost was low and fans continued to sound like they werre engaging even when I first started truck for the day. Had truck towed to shop, because it cut off on me when driving.
At shop : Truck had air filter, water in fuel sensor, o-ring for draining plug, new ICP sensor and harness, and HFCM cleaned up as it was filled with gunk.
After shop : Fans quit being so loud, but have not had near the boost I had before issues started. Truck struggles to go from stop, and around 15 psi boost gauge starts shaking erratically. Also, I have been losing coolant in a short period of time, and can't see any leak coming from anywhere, and also my radiator has been making a sloshing/gurgling noise and it will stop, then come back all within bout ten seconds. And I guess while I'm writing, I should mention the bucking after it downshifts in about third or fourth gear giving it gas makes the truck buck until the RPMs are above 2000 or it upshifts or downshifts, and at an idle seems to miss until warm.
Ford 6.0L Power Stroke Diesel :: Losing Coolant Pressure - Pin Hole Leak Somewhere Once Shut The Truck Off
I noticed when I shut off the truck about 30-40 minutes later I'll open the degas bottle cap and notice there is no pressure.
I used a coolant pressure tester kit and pumped in 16PSI but couldn't hear or find the leak.
I'm going to buy a smoke machine in a month or two but until then, can I still drive the truck ?
I'm guessing it is a pin hole leak somewhere as once I shut the truck off... there is a lot of coolant pressure.
Ford 7.3L Power Stroke (1999-2003) :: Oil In Coolant / Oil Level Drops But Coolant Level Stays The Same
My friend bartered for a '99 F250, 2wd/auto, 4 door, 7.3, 258k miles.
It had reportedly sat for one year, though the expired registration sticker and other things point to it sitting for two.
It ran low on oil, sputtered and died. Oil in the degas tank. Filled to oil to mid way on the hatch marks on the dip stick.
I drove it 25 miles to my house, and the oil level is not reading on the dip stick.
The sludgy fluid level in the degas tank is unchanged. Where is the fluid going?
I will refill the oil to see just how much it lost in the 25 miles if it important to someone, but I prefer to not waste the oil.
My first plan is to remove, inspect and replace the oil cooler o-rings. Even though the dealership charged him for this, I don't trust that they did it right. I think it is the easiest and mostly likely place for oil getting into the coolant.
It does have a really long crank before there is enough low pressure oil for it to start. At the moment I think this is a separate issue.
The dealership also charged him for a replacement injector. No idea if they replaced the cup or not.
Ford 7.3L Power Stroke (1999-2003) :: Coolant In Oil - Engine Is Out
Had coolant in oil, so pulled motor. Got used motor to replace it with, thinking about doing some work on it before reinstall.
Got bellowed up pipes, injector o-rings, front and rear main seal, and will use best parts from both motors to make one. I'll also shim injector armatures back to spec.
Should I do injector cups too? What else is recommended to do at this time? Both motors are 350k or so, I was on a budget at a moment and have to make it work with what I got.
Ford 7.3L Power Stroke (1999-2003) :: Oil In The Coolant - Normal?
What is the effect will some oil contamination is the cooling system?
Does it significantly affect the cooling efficiency? I have some oil the coolant on my boat. I do not believe it is a lot maybe a few oz, but I have been chasing some unexplained overheating issues. Will adding water wetter solve oil issues (if there are any). The other option is Dawn and several cycles of flushing the system. ie until the cows come home!
Ford 7.3L Power Stroke (1999-2003) :: Coolant Overflowing Through The Cap
I have a 2002 excursion and every time I try to put the coolant at the min level cold, it overflows through the cap until it is about 1.5-2 inches below the min level. Then it stops. I just did the oil cooler seals last night because I had a little oil in the coolant. Same thing happened this morning - overflowed again.
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Coolant Seen While Injector Out?
Although not certain, I *thought* I saw coolant run into the front drivers side injector hole when the injector was out and I leaned on the radiator hose. I had knowledge t pull them and changing the orings who were initially concerned then not concerned after looking closer.
Either I made a mistake in what I thought I saw on my first experience with injectors, or there really is a problem that I didn't know enough about to address at the time. So I opened this thread to get more info and stop hijacking 67speeda's thread, found here: [URL] ....
As per recommendations, I will check my coolant bottle for any fuel, oil, residue, etc. I am also going to reach out to my buddies and see if they saw a problem with coolant, too, or they realized it wasn't coolant and I didn't take note of it ...
It was a REALLY LONG day and my ability to concentrate had begun to slip quickly (health issues), so it's possible I missed something there. So IF I saw coolant going into that cylinder with the injector removed, how bad would that be? I thought it came from pretty high up and ran down where the injector sits..
Ford 7.3L Power Stroke (1999-2003) :: Oil / Coolant Leaking Down
So just a couple hundred miles ago I changed the oil and oil filter in my 99 7.3 ... It wasn't till today I noticed an oil/coolant leak ... It is on the driver side of the engine by the oil cooler ... "It isn't the oil cooler leaking already checked"... It seems to be behind the water pump to the driver side of the hpop... Where the thermostat is it is like right behind that but I can't think of what it is .... Its not the oil pump leaking ... It is leaking down and being blown back across my oil pan and oil filter... That is the oil cooler it has residue but its not the problem
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Won't Start - Bad Injectors - Coolant In The Oil?
So we begin w/ another saga for the 7.3l Excursion......
A few months ago it started running like crap, real crap and blowing white smoke like crazy. Well I knew this from a previous episode and I had a bad or multiple bad injectors. I tried to trouble shoot which one it was and maybe just replace the one or two....but no it was worse than that. So Life was really busy it kinda got shoved aside until now.
I pulled all the injectors and had them rebuilt locally ..nice. They ended up being with mech for a couple of weeks because he went out of town...no problem. Well this entire time my rig was untouched and when I got them back #7 was full of water.....great, bad injector cup. #7 was the only one, the rest were dry. So I drained the radiator and the oil and left it overnight to completely drain and installed the new injector cup in #7. Next day I refilled via both heads because the valve covers were off, 4 gallons of oil and a new oil filter. Cleared the cylinders via the glow plugs and commenced to trying to get her started. Nada......just cranks, killed the batteries, recharged over night and left the box on them and still nada....but the oil was still very milky at this point.
So tonight I pulled all the injectors back out and drained the oil again, still a lot of water. This time I sucked out the HPOP reservoir and got a more milky water/oil out and I'm leaving everything open all night.
In the am I plan to check my overflow water level in the hopes it remains at the same level...if so I will reinstall all 8 injectors and refill the motor w/ 4 gallons of fresh oil and try again.
Oh, while I was attempting get her started I put my buddies Snapon scan tool on it and I got the p1271-p1278 codes w/ the buzz test. (low side to high side open circuit between idm and injector) So I found the pin test with everything connected at the idm pigtail and everything tested good. So I'm back to my not so fresh oil anymore is the culprit to it not starting.
Am I missing something here?
Also....another fun filled fact is that I seem to have a fuel leak somewhere at the rear passenger side. Every time my fuel bowl fills up, if I shut the key off it will drain down. Sometimes I can see fuel dripping quite vigorously onto my starter but I can not see where it is coming from. I have while it was dripping ran my hand along the head and the fuel lines and can not find where it is coming from. Any thoughts as to where in the hell this fuel could be leaking from?
Ford 7.3L Power Stroke (1999-2003) :: Low On Coolant / Oil Droplets On The Starter
Edit, I have also noticed I have been getting low on coolant, but without any noticeable coolant leaks. My engine oil still looks clean, where could the oil be going? How do I fix it?
2003 Excursion 153,000 miles - stock injectors, gt38r with new pedestal, Adrenaline HPOP, double transmission cooler.
I've noticed after some heavy towing with my camper (8,300 lbs), I've been getting a new oil leak showing up on my garage floor. I crawled underneath this afternoon and found three large oil droplets on the starter. See picture. What could this be dripping from?
Ford 7.3L Power Stroke (1999-2003) :: Check For Fuel In Coolant?
Is there any kind of test short of sending a sample to Blackstone or the like to verify if there is actually fuel in my degas bottle as opposed to oil residue from bad oil cooler O-rings?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Loss Of Coolant And Odd Engine Noise
I am trying to figure out the problem with my 2002 ford 7.3 Engine.
[URL] ....
It has a lost of engine coolant. The oil is 100% clean with no signs of Coolant. No chocolate milk effect. Also it makes a Odd thumping noise at idle. I think it is coming from the Exhaust Manifold.