Ford 7.3L Power Stroke (1999-2003) :: OD Flashing When Driving After New Trans 4r100
Well stock trans went two weeks ago so warranty company had another stock one put it (4r100). Finally got the truck today and I noticed my overdrive was flashing. I have no issues though shifts fine speedo works Rpms are normal I checked fuse 19 under the dash that's fine so I'm lost
If I turn the key on I can use the button like normal but once I drive it just flashes. It works but flashes .
Ford Super Duty (1999-2016) :: F250 - Trans Shifting Hard / OD Light Flashing / Code P0720
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 4R100 Trans Won't Go Into 4th / OD Light Flashing And Occasionally Overheats
I have an early 1999 Ford F350 4x4 7.3. I purchased it used about a year ago. The trans was replaced with an ATS 4R100 and a billet torque converter. I have the paperwork for it to confirm it along with the mileage when it was installed. It currently has about 35k on the new trans.
Several months ago the trans heated up to about 200 degrees on my trans temp gauge that was already installed when I purchased it. Not a huge deal and after pulled over and high idling it off I went and no problems.
About a month ago I was towing my fifth wheel when I noticed the temp rising on a level grade. I also noticed the OD light flashing. I made it home and when I went to drive it the next day light was not flashing and it shifted and drove like normal without the trailer.
I towed the trailer again and same thing, OD light flashing and started heating up. I changed all the fluid and flushed it based on the trans flush procedure I got in this forum and replaced with an OEM trans filter. Towed the next day and everything was good. Temp was good and no OD light flashing but I lost 4th gear. All other gears shifted fine, no slipping, just won't go into 4th.
On my way back home the OD light started flashing again and instantly the heat started rising on the trans again. I was finally able to get it into 4th if I let off a little, but as soon as the OD light started flashing I lost it again.
I have a friend of a friend who works for Ford who offered to come over to hook his scanner up. When he hooked it up there was no stored codes from the OD light which we both thought was odd. Took it for a test drive and the OD light started flashing so we could get some readings. He said it showed an error shifting from 1 to 2 and another error when shifting from 3 to 4. I unfortunately forgot to ask him for the specific codes. He tried to read the torque converter info but said my truck was to old and the PID was not supported to read that info.
He said it appeared it was mechanical but without some type of break out box where he can physically shift the gears he couldn't say for sure if it was mechanical or electrical. He did not seem to interested in doing that test for me as he rebuilds trans on the side and said he could rebuild it for me.
It seems my overheating takes place when the OD light starts flashing. It still drives fine and shifts smooth with no issues with or without the OD light flashing. 4th gear usually doesn't work but on a rare occasion it will go into 4th fine which makes me believe it may be electrical.
I am new to diesels but have learned a lot about my 7.3 lately. I recently installed injectors, up pipes, hutch mod, and several other little things so I can get things done myself but am just a DIY'er who can follow good directions. I know very little to nothing about transmissions though.
While working on another issue I did notice there is a large wiring harness that connects up on the driver side of the trans. I unplugged it and was checking the wires and after removing the dirt and crud on it you could see the outside wire sheathing had deteriorated exposing the copper. I bought some liquid electrical tape and sealed everything up. I did look for a replacement wire harness at the time and the one I ordered was very similar but the plug was different so that is why I used the liquid tape at the time. I did not seem to have a problem at the time after fixing it but wanted to mention it here in case that may be an issue.
I also thought swapping out the solenoid pack may fix it. I did not want to drop the trans and send it for a rebuild if I did not need to. I know there are some other sensors associated with the trans like the TSS I think but don't know if they are even related to my issue.
I tried getting the codes from the guy but he does not have them and I can't get him back out. I have an OBDlink device connected to Torque on my phone but I couldn't get it to read trans codes. Could be user error.
Ford 7.3L Power Stroke (1999-2003) :: Hard Shifting - SES Light Lit Up
I have run into a problem. My early '99 7.3 PSD decided to throw a very hard shift at me the other day, lit up the SES light and I had to limp it home going 5mph.
I looked on here and found most problems that caused power loss/engine die and replaced the ICP, IPR, EBP and tube, and the CPS. I also did an oil change after all of that to make sure everything was clean when I went to start it up.
BUT, when I tried starting it, nothing happened. It cranks, but does not start. What is the problem? I watched hours of videos and read hundreds of pages of instructions on how to replace everything, and now the truck won't start.
Ford Transmission :: 1994 E350 - OD Light Flashing And Trans Shifting Hard
I have a 94 E350 with a 7.3 diesel. I took it to the Ford dealership to have a new fuel filter and oil change when I got it back the OD light was flashing and transmission shifting hard. They tell me they cannot find a problem could they have possibly knock a wire off of something to make this happen...
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 4R100 - Overdrive Light Flashes And Shifting Really Hard
I have a 2001 3/4 pickup. Sometimes the over drive light flashes. When it flashes it shifts really hard and sometimes it won't shift into 4th until I mash the overdrive button. Sometimes the light doesn't flash at all and it doesn't have any trouble shifting at all. Is it a solenoid? Or wiring issues?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 E350 - Overdrive Light Is Flashing - Shifts Hard
Here is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Trans Not Shifting Into 1st Or 2nd / Truck Acts Like In Neutral
So I put in new clutch yesterday. Reverse works, granny works, 3,4,5 work. ZF6 manual. But when I try to go 1st or 2nd. Its as if the truck is in neutral....what should I be looking for. I bought the truck having only knowing the clutch was completely shot, was not told about this 1&2 gear issue....
Do I need to pull the trans out again... or is there something I can see or adjust, because from what i can see where the shifter connects there is no adjustments. Is it probably a gear selector fork...or connection that took a crap. when moving in granny gear i did not hear any irregular noises....
Ford 7.3L Power Stroke (1999-2003) :: Trans Not Shifting Out Of 2nd Gear - Code PO782
My friend has just brought a truck and has lost 3-4 gear in the auto trans. We have the PO782 code coming up. Is there something in particular we should look at first.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 Leaking Fluid / OD Light Start Flashing
Saturday morning my grandpa drove my F350 into town pulling our 4-horse trailer (With living quarters). I wasn't with him, but I was told the following: he started smelling something hot and noticed the O/D light start flashing. Now, this man is not the most intelligent man on the planet and uses the O/D to "slow down the engine" when he starts and stops - i.e. uses it as trailer breaks. I have asked repeatedly for him to quit, but as best as I can tell, he continues to do so.
After the burning smell, a driver pulled up next to him and pointed down - he looked to see smoke and the truck puking fluid everywhere. He said he thought the truck lost power because he couldn't get it to move. Ended up getting it towed. The tow truck driver checked my fluid level and said I had an extremely small amount of transmission fluid left in the truck...which made sense as the fluid was all on the ground underneath, lol. Fluid was NOT red and looked really gross and there was DEFINITE burnt smell to it.
My question is this - what in the world could have caused the truck to do this (I read that is could be from overheating?), and what should be my next course of action? It is home and in my backyard right now (Classy!). It starts and runs fine, but since there is little to no fluid left, you have to hammer down on it to get it to go anywhere. It does move, however.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Trans Shifts Hard Sometimes
2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Tranny Slipping And Not Up Shifting Then O/D Started Flashing
I spoke with a few people here before about my 4r100.. it threw a code a month ago for P0750.. i replaced solenoid and it continued to do it even after clearing codes numerous times.. then all of a sudden it was perfectly fine for over a week, no codes, i ran a few brick hauls with it and ran it for over an hour straight.. i went to fl and upon return i took her for a drive and wouldnt you know, the code has returned.. i did hammer down a little but not from a dig, i just got on it a little playing with a neighbor and his truck and all of a sudden it did its thing slipping and not up shifting then the O/D started flashing again... i cant understand why the code would come back all of a sudden, there has to be a wiring problem correct?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Trans Slipping On 25hp Tune Up High In RPM Band And Shutters When Up Shifting
My excursion's trans is slipping on the 25hp tune up high in the RPM band and shutters when up shifting. I have dropped to stock most of the time, but I know i am on borrowed time.
I had a JW trans in my e99, and there is no question on the durability and performance of the transmission. The price has gone up a lot, but that's maybe not the big issue.
I live in the mountains and spend a lot of time pulling and just driving in that 40 to 60 mph range over mountain passes. That is basically where I spend ALL of my time.
The distance between 3rd and 4th is driving me CRAZY! I have researched everything from swapping to a manual, to PCS controllers, to trying 4.11 gears, to overdrive units.
Swapping Manual: ZF6 is the obvious candidate, but I have read the swap is not probably something I have the skills or tools to do. I have also read that the performance of the ZF6 is sub par. But it seems like it would give me my 3.5 gear that I am looking for.
PCS Controller: Looks cool for a way to have control besides using the tree shift. Maybe a compromise on not swapping in a manual.
4.11 Gears: I get pretty excited thinking about the low end torque etc. I go off road almost every week, and like I said, I hardly go over 75 mph. But once in a while I do. Right now, the truck turns about 2300- 2500 rpm at interstate cruising speed. Looking for 4.10s rpm in that range to compare? Also, how bad of a fuel economy hit would I take? What is the cruising rpm of 4.10's between 60 and 65 mph, or in general what is the rpm change?
Overdrive Unit: I have always been interested in more gears, but I read about someone who installed one behind a 7.3 and didn't have they great of results. To the point where he said it wasn't worth it.
Ford 7.3L Power Stroke (1999-2003) :: No Overdrive - Hard Shifting From 3rd To 4th
So I have a 2000 F-250 7.3 and my over drive won't work. I also had hard shifting from 3rd to 4th and 3 gear wouldn't try to shift until about 2500 RPMs which is high. I replaced solenoid pack and no change. I have rebuilt the tranny and found that OD snap ring had came off I put upgraded spiral ring on. When I went on a test drive I found out nothing had changed except shifted smoother. So I changed valve and accumulated body still no change. Truck is throwing 4 codes:
P0733 Gear 3 incorrect ratio
P0750 Shift Soleniod a fault
P0783 3-4 shift error
P0541 intake air heater a circuit low
Could it be PCM??
Ford 7.3L Power Stroke (1999-2003) :: 4R100 Trans Shifts Hard When In Any Position Other Than Stock
I just bought a 2002 F250 7.3 4x4 auto. It had a TS 6 position tuner installed. In stock mode, I got about 11 mpg. I wasn't too impressed. I found that when I left it in 75hp mode, my mileage went up to 21. I drive easy and try to keep shifts at or below 2,000 rpm. The problem is that, when in any position other than stock, my transmission shifts HARD.
My question is: what's going on here? Does the TS change the transmission shifts? Or is the extra bump in power enough to stress the tranny? Based on the factory gauge, the transmission is not running hot. The fluid is nice and pink with no odors or metal shavings. I'd hate to prematurely kill my transmission, but nearly doubling my fuel mileage is hard to pass up.
Ford 7.3L Power Stroke (1999-2003) :: Turbo Whistle Under Hard Pedal Before Shifting
I have a 01 7.3 F-350, 120000. I rarely get down hard on the go pedal but a while back I did and heard at pressure whistle just before it would shift. I thought a bad turbo hose so I replaced them all. 'While working on the hose mounts I cleaned up the castings for a better seal'. The hose replacement seemed to get the running but the whistle is still there. I am thinking a leak on the manifolds for the Y-Pipe connection OR does the turbo have a release valve that can make a whistle sound?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Strange Turbo Sounds And Hard Shifting Into 3rd With TS6
I put a ts6 on my 2001 7.3. I love it shift points are better and truck has a lot more power. But I've noticed when I shift truck shifts into 3 (especially going uphill) I get a really weird turbo sound where it acts like its gasping for air (I have 6637 air filter) and then it shifts kinda rough into third. If I put chip on stock setting it doesn't do either of the things I described. Do I have loose turbo boots somewhere or possible bad turbo bearings?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Hard To Start / Misfiring At Around 30% Throttle Driving
03 6.0 with 90k miles. New heads, all orings , stand pipes, injectors , glow plugs, egr delete , oil cooler and studs . Has sct livewire. Just took the truck to the shop for a hard start issue and misfiring at around 30% throttle driving. It would fire up great in the mornings with some white/blue smoke till warm. But after it was warmed up you shut it off it would fire right back up but very slow to reach proper idle.
But if it set for about an hour it would crank great start but same lazy idle up but now it wouldn't get over 300 rpm before it would die. And do this for 5 or so more times before finally idling up. Then runs pretty good other than the misfire. So he said it's either the hpop ipr or icp. I had him replace all 3 with motorcraft parts. Still the same issue ! Return the truck to stock tune and it doesn't have any power . My pockets are only so deep...
Ford 7.3L Power Stroke (1999-2003) :: Airbag Light Flashing - No SES Light Or Fault Codes
Came on other day. No ses light or fault codes. What it means?
View 10 Replies