Ford 7.3L Power Stroke (1999-2003) :: Engine Quits Running Randomly?
My engine suddenly stops while driving. There is no warning or loss of power, it just stops randomly after running fine for a while. After some time (might be minutes or hours) the engine turns on and runs fine.
I have no clue what it might be, I believe it might be an electrical problem affecting the diesel pump. The pump has a pair of cables coming in to a white plug at the pump's back, I disconnected them but the engine still runs.
Ford 6.7L Power Stroke Diesel :: Randomly Cuts Out When Accelerating
I have a 2013 that randomly stutters or cuts out for a second while accelerating. This happens whether I am slowly accelerating or full throttle. This used to happen once every few months but it is happening more frequently now. It will randomly happen while trying to accelerate on the freeway. The truck feels like it stalls, then takes off. It feels like it loses boost pressure so maybe a wastegate issue or possibly an EGR valve issue. No codes are set.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 Diesel - Engine Just Randomly Shuts Off Without Warning While Driving
My 2001 F350 7.3 dually diesel Automatic has been a pretty good truck but recently it has been dying. Engine just randomly shuts off without warning while Driving. Check engine light comes on sometimes. Some of the time it will restart if I cycle the key. Once its running again I can rev the engine up without a sputter but after a few hundred yards down the road it will die again. I noticed driving on the highway when it does it my truck will buck first, then...
If I leave it in drive with the key in the run position when it dies and I'm coasting down the highway the Tach starts jumping around like its trying to restart itself, all on its own. I don't have a scanner.
The last time it died I coasted into my driveway and it wouldn't restart, went back out there 30 minutes later and it fired right up. Its only 40 degrees here if that matters, not hot by any means.
Ford - Mountaineer :: 2003 - Engine Randomly Cuts Out While Driving
Was just out and about today with my girlfriend and while driving back home, the engine just randomly cutout. I pulled over to the side of the road and popped the hood just to see if something came undone. Everything is kosher. Started it back up and carried on, but while driving the rpms kept dropping low and when stopped it would drop to about 450-500rpm.
So I put it in neutral and kept my foot on the gas to keep the engine up to about 1000-1500 RPM just so it wouldn't cutout. Drove part of the way home with overdrive off, even though speed limits in some areas won't let me even get into over drive. No check engine light, no messages on the message center, nothing. Looked into it and it seems to be one of several things.
Mass Air Flow sensor
Fuel Filter
Fuel Pump
Throttle Position Sensor
Yesterday I did fill up with gas, so maybe I got a there after they filled up the tanks. 2003 Merc. Mountaineer 4.6L.
Ford 7.3L Power Stroke (1999-2003) :: Cruise Control Cuts Off While Driving
This has happened 3 or 4 times now while driving down the road. Just cruising down the road the CC will just cut out. I'll hit the "set accel" button on the wheel and all is good again until it randomly decides to do it again.
The only thing I've changed recently is the rear end speed sensor to cure the ABS light. I wouldn't/didn't think this would have any effect on the cruise control, but IDK, maybe I'll put the original one back in and test it.
Ford 7.3L Power Stroke (1999-2003) :: Truck Starts Then Dies / Cuts Out When Running
I have changed pickup filter in tank and cleaned 2 tube filters in tank i thought that would fix it.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Engine Just Started Stalling Off Idle And Restarts Easily
Truck has been driving great for a long time and this afternoon after driving fine to work just died 3-4 times while trying to accelerate from idle. Engine restarts easily but the power is soft off idle, the injectors sound noisier and then quiet down and will accelerate decently once rolling but something is off I can tell.
Fuel pressure is read post filter and is good. Truck is well maintained with all the basics replaced in the last couple years. Could this be CPS going out even if it is only a couple years old? IPR is new in the last year, ICP sensor isn't leaking. Most recent change was a full tank of fuel yesterday afternoon and on a whim performing a boost leak check which was all good.
Ford 7.3L Power Stroke (1999-2003) :: Elevated Engine Idle When Cold / Initial Startup?
What causes elevated engine idle when cold or initial startup? Asking another way, what would cause it not to have the elevated idle on start up?
View 14 RepliesPontiac - Vibe :: 2003 - Power Cuts Out Randomly For 5 To 7 Seconds At 70 Mph
I have a 2003 Pontiac Vibe that was new to me in 2011. Pushing 180k+ miles. It was subject to the airbag recall last summer and has been repaired by the GM guys. But last fall I was driving at around 70mph with the cruise on and came up to a speed change so I tapped the brakes to end the cruise and EVERYTHING went dark in the car- radio, dashboard, a/c, the electrical charging plug- EVERYTHING for about 5-7 seconds. Then everything came back on and I continued as normal. My mechanic was dumbfounded. Figured one time freak thing so no worries.
No issues since until this morning. On the drive to work I had the high beams on as it was 5:15 in the morning on a state highway in the country. Came up on a red light so flipped high beams off. EVERYTHING goes dark for 5-7 seconds, comes back on, and I continue as normal. Obviously I'm getting a little concerned at the randomness, not to mention that losing power at 70mph is a little disconcerting. Mechanic is dumbfounded but willing to tear up the dash and steering column and see if he can't recreate the issue.
Ford 7.3L Power Stroke (1999-2003) :: Stalling Out And Dropping Power Randomly
So the truck has been stalling out and dropping power randomly, symptoms pointed to needing the 50 cent mod, changed the cps for cheap insurance and peace of mind just in case it wasn't the uvch, no dice. So last night I yanked valve covers for the first time here's what I did while I was under there, check my work.
1st I ohmed out injectors thru the 42pin harness according to tuglys sig link. My meter would only go down to a 0.4 when testing the test leads just to each other
DS injector ohms
#2 3.5
#4 3.4
#6 3.6
#8 3.6
PS injector ohms
#1 3.6
#3 3.6
#5 3.5
#7 3.6
DS glow plug ohms
#2 prong to ground 2" away 0.9 ; white connecting wire back to gp relay 0.3
#4 0.9 wire to relay 0.5
#6 infinity ohms up thru highest meter setting, checked multiple times and different ground spots,(replacing tonight) wire to relay 0.5
#8 0.5 wire to relay 0.5
PS glow plug ohms
#1 1.0 ; white wire back to relay 0.6
#3 infinity multiple tests as well (replacing tonight) wire to relay 0.5
#5 0.9 wire to relay 0.6
#7 1.0 wire to relay 0.7
Next up, ebp sensor was reading 1.9 higher than map/baro koeo, gently cleaning sensor earlier didn't work. Installed new motorcraft, will check it with Torque pro koeo once the batteries are reconnected
Next I checked the uvch connections which felt good, darn it, maybe a smidge of movement from the DS, but nothing halfway disconnected or anything. Hmm. I ground down the quarters to the top of his head and installed.
Next I torqued down the 4 bolts per cylinder of the rocker arms at 20 ft/lbs, all were perfect and snug
Next up, injector torque. I've read on here below 50, or 80 in/lbs depending on different threads and opinions that I would need to replace o-rings.
So I set the in/lb click torque wrench at 50 in/# and tested the wrench's click on the higher torqued rocker bolts, then checked all the injectors, all were good
Reset for 80in/lbs, tested, then hit all injectors, #6 almost budged but clicked immediately before the handle moved
Reset for 100 in/lb, tested on larger bolt, 2 injectors took a 1/8 turn;
Reset for official spec of 120 in/lb , tested wrench, all injectors took 1/3 to 1 full turn
Reset for 130 in/lb (above official spec, but highly recommended on here by those way more knowledgeable than me on our engines) tested on a larger bolt, slowly and carefully gave all injectors almost an extra 1/2 turn to click; whew, finally a relaxed sphincter.
At this point I knew I needed to buy 2 glow plugs today, replace, then I'll check all glow plug torque at 14 ft/lb in one go, so I got everything ready for a hot torque after I do glow plugs tonight ("unloaded" the torque wrenches) and finally installed the RiffRaff AIH delete plug. My cell phone's alarm went off to get the kids ready for school, so hit the snooze and got everything put up. Now for a nap, then buy 2 Motorcraft GP and check back on here before going back at it tonight.
I also checked the turbo for play in all directions, was nicely solid and spun smooth, no wheel damage. Up pipes and well basically everything exhaust under hood had zero signs of soot/leaks with inspection mirror.
Ford 7.3L Power Stroke (1999-2003) :: Stalls Randomly And Sometimes Will Not Start
2001 Excursion 7.3 - stalls randomly, sometimes will not start. After the IPR was replaced it was rough for about 4 miles (I thought maybe air in the system), next 40 miles was flawless with 3 stops and restarts. Then it sat for a few hours and I went to leave again and the problem was off and on again for another 5 mile drive. Now it won't start in the driveway. It will start if I disconnect the ICP but the idle is still a little rough.
I replaced the normal culprits after a lot of searching on here:
CPS - replaced with autozone part, thought maybe it was bad new so went to ford and replaced with official part from the dealer
ICP - had oil in the plug and it would idle better removed so I replaced the plug and as much wire as I could - soldered, heat shrunk, good connections - both the pigtail and sensor came from Ford dealer
IPR - replaced with part from the Ford Dealer (FYI - 1 1/8" 1/2" drive craftsman deep socket from sears fit in the ratchet and on the part).
Grounds - found somewhere that the ground on the firewall for the windshield wipers can interfere with the CPS so I pulled it, clean the connections and made sure it was tight and secure.
No check engine light now - I received a few through the process, but did not clear them and there are no codes at this time (self cleared on the 40 mile drive)
I'm thinking it may be some electrical issue/short or a fuel issue at this point, bowl is full and the filter is fairly new (few thousand miles). I haven't done the Hutch mod, but have over 1/2 a tank.
I'm trying to get this going as quick as I can so I don't want to waste too much time, but I also don't want to miss a critical troubleshooting step to take.
Below are my thoughts on the next steps.
Research and test fuel pressure
Tow it somewhere to test each injector - I only have Torque pro to read codes and engine status
If fuel delivery checks out ok, start testing wire by wire on all of the above parts.
Ford 7.3L Power Stroke (1999-2003) :: Cough Randomly On The Interstate?
My 7.3 will cough randomly on the interstate not towing or anything. It has a new turbo and filters...
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Coughs Randomly About 70 Mph On Highway
When driving my truck it coughs randomly not towing or anything going about 70 mph drops rps slightly and goes right back. It has 212000 miles new turbo and filters...
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Randomly Dies Will Not Restart
Ok, so my 2002 f250 died on me last Tuesday out of the blue, pulled it home and found fuse 23 I think ECU power was blown. I removed my Hydra, and put a new fuse in it and all seemed well, then Friday evening on my way to dinner was driving along and truck shuts off like someone turned the key off. I replace the Crank sensor, even though I had put a new one in after the first time it died, which was last Tuesday, still would not start.
Pulled it home, went out Saturday morning to look at it and hit the key and it fired right off. At this point I don't really know where to look, I wiggled every wire I could find while it was running Saturday and no change, but it does seem to have a miss in it while it is idling...... I am not sure where to start looking....
Ford 7.3L Power Stroke (1999-2003) :: Charging System Light Goes On And Off Randomly
My charging system light in my 2000 F250 keeps coming on and off and very random times. Its been happening for quite sometime now and I finally joined FTE so I figured I would ask everyone what could be causing this. Ive disconnected all the electrical plugs from the alternator and made sure they were in there well.
It all started when I was cleaning my engine not too long after getting the alternator replaced. I don't remember getting any water anywhere near the alternator and cant understand anything causing this other than the connectors. It will cut on and then cut right off sometimes and then sometimes it comes on and stays on...
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Smoke White Randomly?
my 2000 f350 7.3 is acting strange lately. Its got 252k and is all stock other than exhaust,intake,ww2. It smokes white every random once in a while for some reason. At start up it wont though. If i get on it every once in a while it will smoke white then go to back to black. Im not consuming coolant, and the oil looks fine, no residue on the oil cap and its not puffing out the oil cap either. Other than that its running great just dont know why it goes white every so often.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 - Battery Light Flickers Randomly
I have a 99 f350 7.3l 4x4 and my battery light flickers randomly. I have checked the alternator and both battery's. All brand new and seems to be ok. They only are getting a charge when the battery light is flickering. I put both new batteries in on Thursday and on Sunday I needed a jump at the store.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Has Begun Randomly Having A Delayed Start
As would be expected things deteriorate on a 16-year-old truck. My alarm has, on a few occasions, decided to annoy anyone around by activating for no apparent reason. This has happened in various conditions (in the parking lot, in the driveway, right after I've driven it, or sitting half the night). I chalked it up to aging circuitry.
Now I've picked up something new. Over the last few weeks my truck may or may not arm. It seems to be a flip of the coin. I'll drive to the store and I push the button on my remote and the truck goes "beep"..."beep". 10 minutes later I drive home, park the truck, push the remote, and the truck goes "beep"...and that's it. My alarm light is blinking two quick flashes when this happens.
Since this has started my truck has begun randomly having a delayed start. I'll disarm the truck, turn the key, and nothing happens for about 1 second or so (seems longer) then the truck starts normally.
Both of these issues started pretty close to the same time. I would normally go straight for a starter issue but I don't know if these might be related. I'm the second owner so have absolutely no idea about the Ford anti-theft system, how it's connected, or what the blinking lights mean.
I'm considering disconnecting the anti-theft system to see if that makes a difference but, as stated, how it's connected, what I might disable, or how it works. Was there any documentation published on it?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - 4x4 Won't Working - Engages Randomly While Running?
I have a mostly stock '02 F-250.
The other day I parked the truck and as I was walking away I could hear what sounded like the 4x4 clicking on and off. I wasn't sure. I figured I would continue to run the truck to get more symptoms and come up with a diagnosis.
Later, backing out of the driveway, I heard what sounded like a buzzing/grinding noise, like something was trying to engage. It quickly went away.
The next day, the 4x4 light came on as I merged onto the interstate. I pulled over, tried switching the ESOF switch to get it to turn off. I never heard 4x4 engage or "felt" it. Re-starting the truck got the light to turn off. It hasn't been on since.
Today the truck made more buzzing/grinding noises. When I tried turning on 4 high with the ESOF switch I got no response. It went into 4 low and the light came on.
I re-started the truck. Tried putting it into 4 high again and the light came on. When I put it into 4 low the light quit and wouldn't come back on.
I run with my hubs unlocked and they were unlocked at the time, FYI. Also, I have air coming out of the vents, so no vacuum issues. I actually disconnected the 4x4 vacuum lines because I don't use the automatic locking future anyways.
I did do some work with my truck and boat during the flood in Louisiana and I took her through really sketchy stuff. My guess is that the ESOF motor is shot, most likely from being submerged.