Ford 7.3L Power Stroke (1999-2003) :: Turbo Is Out - EBPV Delete
While my turbo is out I decided to delete the EBPV. I removed the butterfly and rod, & pounded in some 3/4 inch freeze plugs. Are there any mods that need to be done to the pedestal, or can I just leave it the EBPV plunger unhooked? It's not leaking, but will it leak if left unhooked? Or do I have to gut it and tig weld the oil gallery's
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 - No Power After EBPV Delete
2001 F350 just rebuilt the turbo, did the EBPV delete now no power.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Hard Cold Start / Now EBPV Not Working
It's been a while but thats because the truck has been performing well.
Current problem: The truck has been hard to start this year as if the glow plugs are not working or are bad. It will start right up if I use the block heater.
Just recently, I also noticed that the EBPV is not coming on when warming up the truck.
Also, This winter season, the engine temp is not coming up to normal. the engine temp needle is more on the low side towards the C and definitely less than 1/2 way up where is normally is. When driving on the highway, the temp comes up more. but sitting at idle it barely gets warm.
So not sure if all 3 are related or not, but looking for a starting point.
Ford 7.3L Power Stroke (1999-2003) :: Torque Specs For Tie Rods?
What are the torque specs for tie rods for a 4x4.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: How To Switch Out Of 4WD When ESOF Is Broke
My ESOF crapped the bed as the truck was stuck in 4 Low. I took the transfer case motor switch off to access the gear underneath it.
I'm able to get vise-grips on it but it only turns clockwise. It keeps turning to a point it won't turn anymore and, if I let go, it will switch back to its original position.
I can do without 4WD until I get ESOF fixed, but is there a trick to manually changing it to 2WD?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Blowing White Smoke - Low Power - Rattling Noise From Engine - Broke Down?
Moving my worldly goods from California to Oklahoma in a rented 26' box truck with my wife following in our '02 F350 loaded to the gills with my lathe, mill, air compressor, weld and assorted machinery. Just west of Deming NM it started to blow lots of white smoke and down on power. Some rattling noises from the engine when throttled up & won't reach 3000RPM.
Had it towed to an impound yard for storage. Plan on sending a flat bed to pick it up when we get to Tulsa.
Any experience with a tilt back trailer capable of loading & transporting this truck that weighs around 17,000 pounds? My plan is to continue on to Tulsa & make arrangements from there.
Ford 7.3L Power Stroke (1999-2003) :: Broke Off Bolt In Exhaust Manifold To Head
Well i had an exhaust leak on this F250 and so I started torquing the bolts on the manifold to the head. (45 ft.lbs) A couple were very loose so I was thinking "Great, this may fix my problem!"
My first mistake was probably the Harbor Freight Tools torque wrench.
I am on the driver side, second from the rear and then bang! I see a gaping hole where the bolt used to be. Bolt on the floor. I cant see up in the hole to the head, I think it broke flush with the head.
Ford 7.3L Power Stroke (1999-2003) :: Cam Sensor Won't Working?
i have a 99 f250 7.3 powerstroke. the cam sensor was acting up. that what the scan tool said. i replaced the cam position sensor yesterday, and the truck is still acting up. the motor hitches and will shut off randomly. it tripped the check engine light, and the code is the "cam position sensor" once the truck is warmed up and shut down for like 10 minutes the sensor will not act up anymore. if i just start the truck and run it, even once it is up to tempature it will act up. but if i shut the truck down for about 10 minutes, it goes away. is there something else that could be causing this?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: No ABS Sensor Wire On The Front?
I have an new to me 1999 4x4 F350 that I was giving a good once over today on the front end since it wanders a little bit. but anyways I didnt see a abs sensor wire on the front. the plugs are there behind the inner fender well and it looks like there is a plug when the sensor should go in the wheel bearing. was 2 wheel abs an option on these trucks? is there anything else this changes front end wise?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: No Start / Oil On ICP Sensor Connection
I have a 2002 F-250 7.3L with 175,000 miles and it died on me July 30th. Here were the symptoms when it died:
Engine was sluggish at standard RPM about 1300-1500 going about 45 MPH, so I stepped on the gas and it seemed to go away. About another 5 miles down the road and starting from a stop, the same thing started happening. The entire truck seemed like it was going to shake itself apart and with the peddle at half throttle it revved to 3500 rpm and didn't shift into 2nd gear until after about 5 seconds at that RPM. After it jerked into 2nd gear the engine dropped back down to about 1000 RPM and started shaking violently again. At this point I managed to make it to a shopping center and then as soon as I let off the gas (still shaking), the engine dropped to 500 RPM and after about 15-30 seconds shut off. When I got the truck home I managed to start it one more time but it shortly stalled after about 15-30 seconds, again it was hovering around 500 RPM and still shaking badly.
Here is what happens when I try to start it:
From 0-2 seconds, truck goes through a normal cranking rhythm and sound.
From 2-10 seconds, it slowly tries to start itself back up but it sounds like it is only firing on a few cylinders, I'm guessing maybe 2-3.
I stopped after 10 seconds in fear of burning out the starter or killing the batteries.
Troubleshooting:
Removing the connection to the ICP sensor, something I read that might at least let me start the truck, which is how I found the oil on the connection itself. I also noticed a little bit of what looks like oil on the some of the wiring harnesses in the surrounding area. I also checked the fuel bowl and it is filled with fuel.
Possible solutions?:
From what I have read on the forums I am guessing that it has something to do with the ICP or the IPR sensors. I also believe that it is a sensor related issue considering that the truck won't even start. I am completely off track. I am going to start working on it full stride this weekend. I have been vehicle-less since the 30th so I'm trying to get this fixed asap. I don't have any codes, I am going to try to get a coder this weekend.
Ford 7.3L Power Stroke (1999-2003) :: Replacing EBP Tube And Sensor?
I am doing some maintenance and trying to replace my EBP tube and sensor. I luckily have the dual alternator package, so getting the tube in and out has been a pain to say the least. I can't for the life of me get the tube back into place. As always, a 20 minute job is taking me 2 days.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: How Critical Is The Intake Air Temp Sensor
Noticed a while back that the plug for what I assume is the air intake temp sensor is looped. I assume because I can't find the sensor anywhere. how critical is the sensor? The new S&B has a hole for it so it's either gonna need a new sensor or a plug. The local autozone has one for 16.99.
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Where To Install Oil Pressure Sensor For Gauge
I need to install an oil pressure sensor sending unit. I've already occupied the 1/8"NPT test port on the rear of the oil cooler, where else might I be able to tap into oil pressure? (LPOP)
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Outside Temp Sensor For Overhead Display
For some reason my OH display decided to show 140 deg F when its 40 deg F outside. Continues to show 140 all the time now regardless of out side temp. In case its the related outside temp sensor sending unit, where it is exactly on an 02. Unless someone has solution may try changing that out to see if that is the problem?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Stalling Out - Water In Fuel Sensor
My 2000 F350 7.3 has been stalling out with the water in fuel sensor for the last to tanks of fuel. I thought I needed to buy a new Titan fuel tank, I pulled the tank and was surprised to see that my tank was not a metal tank, It's polyethylene, I bought the truck in California with 60,000 miles it has 180,000 miles now. It was sold new in Canada, I expected the tank to be metal with the the liner coming off.
The two fuel filters in the tank are just about plugged solid I'll be removing them and repiping the return line. When I repipe the return line do I put the duck bill on the end or just leave it open? Also I searched the web for hours looking for a stock size polyethylene tank with no luck. On the bottom of the tank I found The ford part #s. I'm going to siphon the fuel out of the tank today. and reinstall....
Ford 7.3L Power Stroke (1999-2003) :: Engine Coolant Temp Sensor?
I drove my 99.5 7.3 F-350 1 mile to a friends and hooked it to the OBDII to get a code for my abs light.it had not been drove all day. we hooked into the pcm and he noticed the temp at 375* it was idling. is this right he didnt think it should have been that high???Will the engine coolant temp sensor, if it were bad,show a high temp of 375*? On the OBDII it showed a temp of 375* .....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Code P0197 - Engine Oil Sensor Low
Ok I have a p0197 engine oil sensor low.. Temperature is cold right now and truck was not plugged in.. Truck surges when started unless I give some steady throttle and oil warms up. Also service engine soon light comes on.. Oil change soon but been a while.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Sensor Behind Bumper Area Of Truck?
What the sensor is for? In the course of removing the rough country bumper from my truck and installing the 2005-2007 factory front end I found this guy hanging out with wires cut. I haven't attempted to wire it back up because I want to know what it is first. It would appear that the sensor is suppose to be screwed in to something.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Back Pressure Sensor
So I have a non ebpv pedestal I was going to clean my sensor on the front because my mileage has went down a bit. My question is is this even worth doing since the valve is not there anymore I have got mixed answers trying to look it up some say it still affects the mileage some say it won't. I cleaned it once about 10 years ago. I have an AE also how do I test it and what should it read if I do need to clean it or replace it?
View 3 Replies