Ford 6.0L Power Stroke Diesel :: 2003 F350 - Tow / Haul Light Started Flashing - Code P0730 Incorrect Gear Ratio
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 RepliesGolf IV / Jetta IV :: 2.0 Auto Transmission - Code P0730 Incorrect Gear Ratio
Just picked up a 2002 golf 2.0 auto for $200. Get the car home start it up and it runs great but... transmission shifts all kinds of funky. Starts in first then shifts to third. If I give it some gas it shifts down to second but has nothing there, just revs. Will not go into 4th at all. Throw my little mac scanner on it some codes come up. Only one that mattered was p0277 if I remember. Do a little search and it comes up as the g68 under the tranny mount. Change that out and had not cel. Still shifting the same but no code at all. Throw my scanner on just to see and get p0730 incorrect gear ratio.
View 2 RepliesAccent LC (2000-05) :: CE Light Code PO734 Which Is Gear 4 Incorrect Ratio
So I got around and decided to fix my transmission my self. Any way I got the code PO734 from my CE light which is gear 4 incorrect ratio. So some people say its the solenoids that cause this issue, some say its the 4th gear clutch...
So, Is it the solenoid or it could be the clutch itself? Ive removed the 4th gear from my transmission today and it looks intact. No weird damage or physical like damage on it... I just don't know which to do since solenoid job i can do myself which will be about 5 hours minimum....
Golf IV / Jetta IV :: Check Engine Light Went On And Code Read 3rd Gear Incorrect Ratio
Bought a Mk4 1.8T gti last year had only about 75,000 on it and drove it for about 10,000 miles. The check engine light went on about 2 months ago and the code read 3rd gear incorrect ratio. It still rode fine until about a week ago when it started slipping. Brought it to the local transmission guys in my town and got a quote at about $3,000-$3,500 to have the transmission rebuilt. The transmission is a tiptronic automatic 6-speed.
View 1 RepliesFord Transmission :: Long Shifting Into Next Gear When Selector Is In Drive - Code P0732 And P0734
I have a 2008 Ford Escape 2.3L V6. About 67K miles on it.
Recently there's been some transmission problems. When the selector is in Drive, it will take abnormally long to shift into the next gear at normal speeds, and will redline if i hit it hard, but if i let off the gas, it will shift. Never hard.
If I put the selector in 2, it will do the same thing, eventually shifting into that second gear.
Gear selector on one, well, it obviously stays in 1st.
Reverse is fine. All shifts are smooth just take forever, and I get the wrench in the dash (means drivetrain/throttle fault as per manual) only after driving a while. The tranny fluid is still very clean, and this as been going on for 2 months.
Ive taken it to about 6 different places. Half say new tranny off the bat. Other half says clean fluid for that long after the problem started means its def. an electrical problem, and that makes the most sense to me. What it could be?
I'm thinking:
-Tranny Range Positioning Sensor
-Input/Output speed sensor
-TCM reprogramming/replace
- I'll even go with reflashing the PCM.
Accent LC (2000-05) :: How To Fix 4th Gear Incorrect Ratio On A Rebuilt Tranny
I had the transmission rebuilt a year and a half ago, when I took it in it came up 4th gear incorrect ratio. The guy who rebuilt it said it wasn't the original tranny that came with the car because it was modified to fit in the car. When I got it back, after a couple hundred miles or so, the check engine light would come on for a day or two then go off. When the check engine was on it would get stuck in 3rd gear, once the light went off all was well until the next time. I took it back to the guy who rebuilt it since it was still under warranty. the P1529 code came up for TCM issue. He put some sensors and a chip in and thought it fixed it, no such luck. Finally I had the cash and had it looked at by another shop and the 4th gear incorrect ratio came up as well as the P1529 TCM code. He's suggestion to fix it was to either get a used tranny or rebuild this one again. He believes since it isn't the original tranny that the tranny in there now was for a SOHC engine, not a DOHC engine and that's why the ratio in 4th gear is off and it throws the TCM code.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Tire To Tranny Ratio - 33s Normal?
What's too big? I just put 33s on my super duty, is it "too much" for the transmission?
View 7 RepliesFord 6.7L Power Stroke Diesel :: Optimum Gear Ratio For DRW - 3.73 Or 3.55?
I got burned with a smoker back in the mid 1980's and have been hesitant to come back. I am currently pulling my 5er and my enclosed gooseneck with a 6.2 gasser SRW. It has the 3.73 gears in it...not the best for towing.
I am thinking about ordering a new SD DRW 2wd with the 6.7 PSD.
Both my trailers are rated at 18000 GVW, what would be the best ratio to order? 3.73's?? 3.55? Fuel mileage will be what it will be with what ever ratio I go with. The truck will be mainly a puller. Not a daily driver.
Ford 7.3L Power Stroke (1999-2003) :: Transmission Malfunction - Got Code P0705?
I was pulling the I-40 ascent to Asheville today while empty, got to the top and started down the other side got to semi flat road and the tach suddenly went up about 600 rpm's. Transmission temp about 180*F. I let off, then resumed and everything was fine. About a mile later it happened again. This time the tranny lost 3rd and OD, still had 1st, 2nd, and Reverse. So, we limped into a service station. Temps hovered in the 170-180 range. At this point there are no codes, no lights, O/D is not flashing.
I shut the truck down to check fluid level and current condition. Everything was fine last night. Fluid level is still good and fluid is still red and clean. I changed fluid about 2k ago and the fluid coming out looked almost as good as the fluid going in.
Got back in the truck started it up, checked for codes and got a P0705, put the truck in gear to get to a diesel shop down the road and everything was fine, shifted completely normally through all the gears. This lasted until about 1 mile from home and then the same thing happened all over again. Fluid still looks clean, not burned, still no CEL, no flashing O/D, but only have 1st, 2nd, and Reverse.
Ford 7.3L Power Stroke (1999-2003) :: Trans Not Shifting Out Of 2nd Gear - Code PO782
My friend has just brought a truck and has lost 3-4 gear in the auto trans. We have the PO782 code coming up. Is there something in particular we should look at first.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Slightly Worn 2nd Gear Synchronizer - Transmission Rebuild?
I am about to purchase a 2001 F450 7.3L with a 6 speed ZF6 that has a slightly worn 2nd gear synchronizer. I will be rebuilding this transmission with a friend and was wonder if there is any documentation available to assist with the overhaul.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 4r100 Transmission - Code P0750 Shift A Malfunction
I bought it 4 years ago with 205K, swapped trans fluid.. 10k miles later (I don't drive it a lot ). I am throwing the code P0750 Shift A malfunction.. i figured id swap the solenoid pack since I am pretty handy and it was affordable.. but it didn't seem to do the trick.. it drove around the block good for 5 minutes before it started shifting weird and throwing a code again.. almost seems to be slipping... I still have to check fluid level again and scan the code again but any suggestions? I have an apt to go to the tranny shop this week and would like to avoid the big bucks if possible.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 4R100 Transmission Will Only Shift To 2nd Gear When Throttle Is Feathered At 2500 RPM
Problems with my 2001 F250 4r100 transmission. Transmission will only shift to 2nd gear when throttle is feathered at @2500 rpm. All other gears shift perfectly. This problem is consistent.
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 4r100 Transmission Loose After Warm Up Especially At 4th Shift Overdrive And Passing Gear
I have a 4r100 on in a 99 7.3 4x4. The shifting problem I have appears to be intermittant. it seems loose after warm up especially at the 4th shift overdrive and passing gear. possibly due to low presures ? sometimes (lately more often than not) hunts back and forth between 4th and o.d when passing or hill climbing. Under normal driving it shifts somewhat firm with 4th being an exeption.I have changed my crank position sensor filters and fluids which had turned dark and improved slightly. When I pulled the pan and replaced the filter the pan was spotless. No residue or signs of plates or debris. There is about 100,000 miles on the tranny and 350,000 on the truck. Questions: Is there a tcm for this transmission and if so could it cause these problems? I'm considering a purchase of an unlocked 1705 superchip to change the shifting but unsure if this will work for my issues...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Auto Transmission Code / OD OFF Light Started Flashing
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
Ford Transmission :: 1986 - Gear Ratio On Transmission?
I have a 3 spee Od out of a 1985 F-150 2wd . I was wanting to put it behind a Onan 6AT diesel . The engine came out of a P-350 bread truck . I runs great . I was wanting to know what the gear ratios are on the transmission . The engine has about 135 ftlbs of torque . The tranny was behind a 300 6 cyl . Iam trying to find out if this tranny will work or will I have to go to a N<!-- -->WC or TKO 5 speed .
View 6 RepliesFord F-150 (2004-2008) :: Code P0731 - Improper Ratio For First Gear
I have a 06 f150 and about a month ago I purchased an edge evolution. Twice in the past 3 weeks my o/d light starts flashing and my truck beeps and it shows Trans Fault on the trucks display. When I use the edge to check the DTC it comes back as P0731. I am running the canned level 3 tune no changes and trucks completely stock other then the edge. Also both times I have been going about 10 mph down a hill without giving it any gas. Also both times of shut the truck off and let it sit for a bit to make sure I wasn't going to break something.
View 14 RepliesFord Super Duty (1999-2016) :: 2001 - Transmission Malfunction - Sluggish - Codes P0732 / P0720 / P0503?
My '01 7.3 is having some transmission problems, My O/D light is flashing. Trying to go after stopping at a light is a difficult, it drives very sluggish, like its not in overdrive. Scanned it and got three codes P0732, P0720, P0503. I replaced the ABS/VSS on the differential and the problem still exist.
View 1 RepliesGolf IV / Jetta IV :: 2003 1.8T - Reverse Not Engaging On Cold Starts / Code P0732
I am having a problem with my MKIV, @ 182k. I think problem first arose a couple months ago when reverse began not engaging on cold starts, so I would have to sit there 5-10 minutes waiting for car to 'warm up' enough for reverse to engage. This led me to taking it to a local tranny shop who I asked to change fluid only, which they did. Problem persisted however, but forward driving was noticeably much smoother. If that matters. I gave up on it, since I knew it was only reverse messing up, and started parking in reverse overnight etc.
Simultaneously I had a code for P0420/P0411 (the SAI incorrect flow crap which causes catalyst inefficiency) so I went ahead and swapped out the cracked SAI plastic hose leading to stock airbox, after doing so I reset the CEL and ran the car. And it ran like crap, I think it was in limp mode (i had never experienced this in my Jetta) from what Ive read, but not sure. So, I pulled to the side, and restarted car, let it sit, same problem. Finally, after 3-4 cycles it threw a CEL, which ironically FIXED the problem. It ran fine from then on. Made it home, hooked up scanner and CEL code was P0732, which I read elsewhere is a 'Gear 2 - Incorrect Ratio' meaning 2nd gear is messed up somehow.
So, overnight I reset CEL and today in the morning I let it idle for 10 minutes before taking off, immediately same issue, where car will not accelerate/ change gears it seems. Went back straight home, waited for CEL to display, and VOILA, runs fine again. Same code P0732. Running fine as of writing this. Problem only arose after taking a swing at SAI code and reset of CEL's. Once CEL lights up its fine.