Ford 6.0L Power Stroke Diesel :: 2006 F350 Stalling Intermittent - Code P2617
I have a 2006 6.0 F350 that has started stalling intermittently. Truck starts right up after a few minutes and otherwise runs great. I'm getting trouble code p2617 (crankshaft position sensor). Reading on some of these forums it sounds like it could be a whole array of things causing this. Would this sensor be a logical place to start or what, if anything, should I look at before getting any parts?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 Stalling When Accelerator Pedal Is Pressed And Released
I have an issue with my 1999 Ford F350 7.3L diesel and stalling when the accelerator pedal is pressed and released.
Background: Initially the truck would not start, and from there here are all the things that I found wrong and replaced. (keep in mind that I troubleshot all the issues and every part that was replaced was proven faulty)... Starting with the glow plugs, all but 3 were faulty and not making a connection to ground. (only one broke off in the head, but I was able to get it out with out getting anything in the cyl)..
Valve cover gasket and harnesses, this is to include replacing the connectors on the engine harness cause both sides of the connectors were broken. The ICP was leaking into the connector and breaking the connection to the PCM, so the connector was cleaned and the sensor replaced. No issues from that now.
The IPR was replaced cause the oil pressure was erratic and not stable when I had my pressure gauge hooked up testing the pressure. After that was replaced the pressure was ok, and it climbed with RPM's and fell back down like it was suppose to. I could not get the PSI up to 3000 PSI even at full RPM's, but it did not drop past 600 psi.
The fuel tank was recently replaced, and all the fuel was removed and "fresh/good" fuel was put in. The fuel bowl was cleaned out and the filter replaced. (the fuel bowl did have a lot of crap in it like rust and dirt). Fuel pressure was at 95 PSI last time I checked, which is higher than the recommended 60 to 65 PSI.
That being said the engine did start and run, but was very rough and missing. So I did all the injector o-rings. Some o-rings were starting to split, and others were not sealing like the copper washer on the injector tip. I could tell by the amount of crap in the end of the injector. ( not the tip, but where the injector contacts the injector cup. There must have been water in there or something cause that part had all kinds of crap around it)
The engine smoothed out after a couple day of running it, but it would still stall when it was cold. The block heater was replaced cause it was falling out. The oil was changed and the filter too. The CMP sensor was changed just because I know they will cause the engine not to start. I had a "known good" truck that I can swap part to and from, and I did a lot of that thus far.
Swapped the IDM, PCM, EBP sensor, MAP sensor, all relays inside the engine and in the cab. I was looking for the barometric pressure sensor, but from what I have read thus far that is a calculation in the PCM between the MAP and the EBP sensors. The diode to the PCM is good,I checked the harness for rubbing by the 42 pin connector and by the LF fender but I did not find any chaffing or rubbing on any wires. The ECPR was wired together, so I fixed it so that it is no longer that way, and the waste gate for the turbo was wired open. I took the wire off and made sure the linkage worked and it did move. I tried to lube up the valve in the turbo for back pressure, but I'm not sure if it worked or not.
I also swapped out the oil pressure sensor and the oil pressure temp sensor on the HPOP Reservoir, and blew out the EBP sensors tube. (air went straight through the tube with no restrictions.) I did a buzz test and all the coils checked out ok. I also did a contribution test and only three cylinders were identified as having some kind of issue. (but this is not enough to cause the engine to stall..) The only current codes that I have are the air intake heater, and the EF feedback not detected. Neither of which would cause the engine to stall in my opinion.
Symptoms:
When cold: The engine will start and idle just fine, but when the accelerator is pressed and held to 1000 RPM's the engine will sputter like its missing and surge up and down between 500 and 1100 RPM's. If the accelerator pedal is pressed quickly the engine speed to increase then fall down and stall. It seems as if the PCM is shutting down and starting back up. ( Like the key is turned off and then back on quickly, but the engine doesn't recover)
When warming: This issue becomes more erratic, but when hot the engine is fine. No issues, and it will drive all day long with no hesitation.
The truck has over 200K on it, but I know it will go more! It is a mannuel tranny, and is a 4X4, and I love it, I can't get ride of it just yet.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Hard Idle And Shutter On Acceleration
2002 F350 single wheel 4x4, 280k miles chipped with a 6
My problem first started when the bottom of my sending unit broke off in tank causing me to run out of fuel at 1/4 tank. I dropped tank and repaired. A week later I noticed fuel dampness on my tank and discovered I crossthreaded cap on sending unit. About this time I started getting a shutter at slight acceleration only and a harder hit at idle. I thought air in lines so I dropped tank and reassembled. No air in line at all now but I still have a shutter so I replaced fuel filter in case of obstruction. No luck. Now since I have owned truck it has been a pain to crank in cold weather if it wasn't plugged in over night. It has been hard lately even in moderate weather since shutter started so I replaced both batteries today.
I replaced the ICP today also because I noticed the other day when there was oil on and around harness to it and when I unplugged it today the truck changed idle and there was oil inside. After I changed it I took it out and it still had the shutter and sound of a miss. At about 8 miles in it just died going down the road. I coasted to the side and it cranked right back up and drove home. The shutter doesn't fill as bad but there. Also I live in the mountains and on my way home after cutoff I had chip in Stock position and had to put peddle to the floor to climb hill. I've never had to do that. I'm getting worried I work for a living and caint keep throwing money at it aimlessly. I'm thinking at this point IPR or CPS. But I'm no mechanic so I could be completely wrong.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Rough Idle And Stalling?
A couple weeks ago my 01 7.3 with 265,xxx started ideling rough and stalling. I had driven in all day Sunday and the next day it started out of the blue! It would barely start idle rough and stall out no CEL. I have singed changed the icp, fuel filter and I have checked oil level. Also used fuel cleaner. Still had no luck. When I changed the icp sensor the check engine light came on and was no change I then got a ford oem camshaft sensor and my truck fired right up but still sounded like it had a little miss here and there drove it for a few weeks fine now back to the same thing it will start up and idle fine for 10 seconds then start the rough idle but won't stall out anymore just idle rough. I am stumped I can't get any codes to pull up and if oriellys uses there scan tool while the truck was running it would shut the truck off! I can't find any answers.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 - No Power Especially While Towing
I just bought a 2001 F350 diesel with 120k miles on it a couple weeks ago. Friday I headed out to Oregon with my 16 foot enclosed trailer filled with jet skis (about 4-5k pounds) for a competition. A few minutes after being on the freeway I noticed the truck did not have good power. About 30 min later while climbing a steep grade the truck almost went dead.
I started at 60mph and by the time I got to the top i was at 15mph with the throttle pinned. the motor sounded funny and shook the truck more then normal. After wards on the down side of the grade the truck started to act normal. I took it to my buddies house and switched trucks because I didn't trust if for the 13 hour drive.
Today I talked to a mechanic at the dealership and he said that it sounded like injector o-rings to him. I went home, pulled the valve covers and started the motor to see if anything is leaking. steam was coming from the valve area and the down spouts on the injectors was flowing oil. The thing that looked especially abnormal was one of the injectors looked like fuel was dribbling from it. I don't know if that is a problem or not. I couldn't tell if it was fuel or oil but no other injectors had fluid coming out near the wire connections.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - No Power After EBPV Delete
2001 F350 just rebuilt the turbo, did the EBPV delete now no power.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 - Engine Cut Off At 55 MPH
The other day I had been driving about 3 hours and truck went dead then back on, it happened two more times in about 30 minutes.
(2001 F 350 Dually 7.3 A/T 2 wd.)
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Acceleration Significantly Slower
I have owned several 7.3's and I have never encountered this issue. I recently picked up a 2001 7.3 with 200k miles on it. When I bought it I knew the glow plugs were going, I also knew it accelerated slow. I went ahead and replaced the plugs, valve gaskets, and added a heavy duty glow plug relay, along with an oil change, and fuel filter.
For some reason, the truck just dose not accelerate very fast at all, significantly slower than any 7.3l I have owned in the past. It appears that I shift at about 3000 rpms and it takes a while to get up to speed. I would like to get it mechanically sound before I restore the body. I was thinking it was the ebpv? but what else could it be?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Power Loss / Hard To Hold The Speed?
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Power Loss And Almost Shut Down At Random Times
I have a 2001 F350 7.3 the truck will at random times loose power and almost shut down. A while back I had an issue with the uvch plugs and changed that out. Truck ran fine till I got some dirty fuel from a diesel tank at my friends farm. I did the hutch mod cleaned the tank and now have a frame mounted screw on filter before the pump. I cleaned the fuel bowl and changed the filter. Fuel pressure stays at 59psi and drops to 56psi wot. The truck is tuned with an edge programmer. After these mods the truck ran awesome for over 2000 miles. Now it has the above stated problem. I have fuel and hpop guages along with egt and boost. During the problem egts will increase rapidly and it seems like it is starving for fuel.
Hpop gauge reads 3300psi or above during wot and shows good pressure during these mishaps. I have auto Enginuity and I get a different reading at wot of only 2600 psi. The hpop gauge is tapped into the icp sensor per instructions and has been installed this way for a while with no issues. The tune has been on the truck for over 40000 miles. The only thing that I can come up with is it will occasionally throw a p1211 under wot or pulling my Gooseneck Dump Trailer when loaded. However it acts up sometimes and doesn't throw the code. Sometimes you can shut it off and start it back up and it's fine other times it will last for the whole day. My only guess is low pressure from the hpop but I don't reflect this from my gauge only on AE at wot. Wouldn't a bad pump act up all the time? Am I correct to think it is just the ipr?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Heat Seat Power Wire Location
I have a 2001 F350 XLT with cloth seats. In 2003 I upgraded those seats to power seats.
- When I upgraded to power seats I did not run a new power wire. Since my 2001 was at least fused for power and heated seats I located the Power seat 30amp power wire.
- That wire is located on engine compartment fuse #15 (Circuit 5298 as I recall) and Dark Green. It comes through the firewall and runs down the drivers side kick panel along the floor and then intersects with the power and ground seat belt wires that ran under the seat.
- The ground wire was coiled and attached to a ground stud behind the drivers side kick panel.
About a month ago I had a mouse get in and chew my seat wiring to shreds. I built my own harness and am good to go there, however since I had these seats all apart I decided to replace the foam and add HEAT.
So that brings me to the specific question. In the engine compartment fuse box, there is a 30amp positive wire for Heated seats. My schematic says it is a 14 gauge wire RD/BK on circuit 1153.
Where in the heck is this wire? I have literally tore the dash apart looking for this wire.
- I have verified the following with my fluke continuity tester.
- It is not part of the four customer access wires that drop on the right side of the interior fuse panel.
- It is not part of the tow wire bundle.
- I have checked the bundle that the Dark Green Power seat wire is in and there are no RD/BK wires in that bundle. I also poked the other 2 14 gauge (Yellow/Blue) wires in that bundle and verified they are not them.
-I have checked the three wire bundles behind the passenger side glove box and was unable to locate.
- I have verified it is not stored behind the compartment below the cigarette lighter.
I am looking for info which wire I am talking about and knows where Ford stored them when not used by having the XLT Trim with cloth seats. Yes I am aware that I can run an additional wire with a 30 amp fuse to the batter, but I would prefer to use the system and fuse that was designed for this.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 Died While At A Stoplight
My one owner 2001 7.3l F350 w/ 265K miles died a few days ago at a traffic light. First time it has ever died on me other than a CPS. This dying was an almost instantaneous with no CEL light, unlike the CPS's hiccuping and dash light up. I put it in park and it started right back up like normal. I continued about my errands and made it home. I have since driven it two more times the same distance and it has not died.
What I have done on this truck the past year.
-Replaced ICP -3/14
-Rebuilt IPR and checked IPR plug -6/14
-Replaced fuel filter every 7500 miles and I am probably due another one of those now
-Replaced air filter - 4/15
-Cleaned out both the sensor and the exhaust back pressure tube
-replaced CPS w/ dark blue unit from RiffRaff in -8/14
-checked main harness over driver valve cover and placed a piece of heavy duty wire cover wrap where they touch the valve cover -8/14
UVWH replace in 2008
Have a new IPR and pigtail coming just because I wanted to eliminate a bad solenoid on it. I also have a Torque Pro w/ blue tooth adapter on an LG tablet that I have yet to set up....but am working on it Will the truck throw any codes if the CEL didn't light up?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Vibration At Idle
I change my motor in my 01 f350 ccsb to a forged rod one from a 97. When I put the thing in my inexperience cause me to screw up my torque converter in turn ruining my transmission. So after a rebuild I put it back in and she fit like a glove. Ever since I put the engine in i get a vibration at idle.
After I realize I screwed up the torque converter I figured that was the cause of the vibration. But now I know the trans is in properly I still have this vibration I'm thinking it's the position of the motor. I installed new motor mounts when I put the motor in but they were quite a bit off from the original points on the cross member.
My only idea to rectify this was to reinstall the original ones and try to position the motor back where it was prior to the engine swap. Or should I be looking elsewhere?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Crank But No Start
I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 Transmission Went Out A While Back
I have a 2001 F350 4x4. My transmission went out a while back. It would only go in reverse. I had it rebuilt and it is still having issues. When I take off with speed from a dead stop it shifts late...about 3000 RPMs. It shifts fine until it shifts into overdrive. It will go into to 4th then right into overdrive causing the truck to act sluggish.
I'm looking into my truck not starting well at any temp too! I didn't know if it could all be connected some how. My mechanic said that when he first started my truck it had a MAP sensor code. He also said that when he unplugged that sensor it didn't change the way the truck ran..Still like crap. I have changed all glow plugs relays and even did the mod to it.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 Died And Won't Start
I have been having problems with my truck for about 6 months now. It start in Sept when my fuel pump went. I got a new pump and went to change it just to have the back clip break off. I fixed the line after getting 2nd degree burns from the boiling water I had to use to expand the line and installed the new fuel pump. Didn't fix anything.
At this point is was dropping below freezing every night ( I live in Canada in the mountains) so I thought it might be my plug relay again... changed that. After that my started has always missed so I figured I would change it out and sure enough the power bolt on the starter was broken. Changed it.
Then it started smoking and I read up on the quarter trick so I figured why not try that. I checked everything and they all checked fine but I am a glutton for punishment and figured I would do that valve cover gasket. So opened it up to find one of my glow plug wires on my harness was burnt up. I have a spare truck for parts so I grabbed the wire and replaced it. Still no change.
Today it was spitting out the usually raw diesel that I have gotten use to but when I was opening the gate to get a manlift for work I smelt oil just to find my turbo coved and the V had a small pool of oil happening there. I added 4L of oil and tightened up my valve cover back bolt on the passenger side... it may have fixed the leak but didn't have time to check.
I backed up to the manlift and it lagged a bit so I gave it a pump of the peddle and it died. Now it won't start. Charged batteries and tried after it cooled down but still no go.
In short my truck has been smoking for about 4 months now. It shutters at low RPM and stalls at the bottom of hills if I gear down on the hill (we have really steep hills around here). I have changed my oil three times in the last 6 months but it keeps coming out black (which it always has). No water in fuel or oil. Once and awhile it had problems starting when it was warm but after bellowing out massive amounts of smoke it would start. The truck turns over but wont start. There is no power where it died so I have to come home and charge the batteries every time they get low but even after it cooled down it still wouldn't start.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 Dies When Hit The Throttle
My truck will set an idle fine but when I hit the throttle it will die.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Intermittent Starter / Whirring Sound When Crank
I have a 2001 f250 ext cab long bed 4x4 that I use as a feed pickup. I have had it for about a year now. one of the issues I have noticed since I bought it is the issue I am having with the flywheel/starter. Its very random like maybe I have a missing tooth or something on my fly wheel. but every so often when I would go to crank my truck over it would just make a little whirring sound and nothing happen ( like my starter gear isn't sliding out and engaging my fly wheel.
After looking through my inspection cover I noticed I had a little wear on the sides but no teeth to my knowledge broken or stripped off. I noticed my starter had one bold loose but other two perfectly tight. It was also covered in oil and dirt from my truck sweating horse power I decided to replace my starter and have my original ford starter rebuilt. I replaced it with a NEW oreillys starter. I noticed it cranked about 5 times as fast but again every 10-15 starts I am getting the same no start. any thing I am over looking?????
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - SES Light Came On / Truck Started Running Rough And Lose Power
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies