Ford Ranger / B-Series :: 1998 V6 - Little Bit Of Coolant On The Bottom Of Bell Housing
I changed the oil on my '98 Ranger 4.0L V6 yesterday and noticed a little bit of coolant on the bottom of the bell housing. It wasn't much (yet), but it was trickling down from above on the driver's side. I couldn't see clearly behind the engine on top without removing some stuff, but I could see where it looked like it was dripping onto the bell housing, ca.3/4 of the way up on the driver's side. Where the leak may be and how to fix it? As I said, it's only a couple drops now, but I'd like to nip it in the bud.
View 4 RepliesFord F-150 - 1997-2003 :: Rod Knocking Sound Coming From Bell Housing
I have a 2003 F-150 4.6 4X4. I had a knocking sound that sounded like a rod knocking but was coming from the bell housing. After some research, I found that it could be a cracked flex plate or bad torque converter. I bought and installed a new torque converter with no change. The flex plate didn't appear to have any damage but went ahead and replaced it with the same results. I actually started the engine by jumping the starter (with no transmission) and the sound was coming from the flex plate/dust cover. My question is do I need the dust cover? Or is it a bearing or something else inside the engine causing the flex plate to hit the dust cover?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Bell Housing Drips Twice?
So I have a bit of an oil leak, bell housing drips once or twice while it is parked for a day or so and usually has a drip hanging off of it. Where the starter mounts also has some oil and there is some of the driver side. The valley is totally dry and I have new CAC boots so it isn't coming from up there. When I look through the inspection port it doesn't look like it is from the rear main. I figure this leaves either bedplate or cam/crank sensor. Any thoughts on how to narrow it down further? Maybe put dye in the oil? It looks somewhat oily up by the cam sensor but it is so hard to see that thing I can't tell very well.
View 10 RepliesFord 6.7L Power Stroke Diesel :: Coolant Running Down All Over The Bell Housing And Oil Pan
The same day that I noticed my coolant temp was running high as I was driving around in my 2011, i was driving around in my corn field cutting wood and i noticed i was dragging something under the truck. when i got out and looked under the truck, there was coolant running down all over the bell housing and oil pan. i was a bit worried that it was my head gaskets leaking but once i got it in the shop and looked at the heads, all looked good. i wasnt sure where it was coming from! so i looked up common coolant leaks on the 6.7 on youtube.
First video was one of the coolant line on the turbo leaking. so i crawled up on top and shoved a mirror down by the turbo and sure enough i could see coolant leaking around the connector fitting coming out of the turbo. apparently the gasket goes bad around this fitting allowing it to leak. i was just wondering if this is really that common of an issue? I did the work myself. and its not really that hard to get to the turbo, its just time consuming removing all the crap around it. all i had to do was remove some connectors that were attached to the plastic intake and remove the intake then you can reach into that fitting. total time was around 2.5 hours.
Ford 6.7L Power Stroke Diesel :: Coolant Leak Somewhere On Top Of Engine Running Down To Oil Pan And Bell Housing
I have a coolant leak somewhere on the top of the engine running down to the oil pan and bell housing. I have done some research and discovered it could be the coolant inlet tube to the turbo.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 Turbo Exhaust Housing Gasket
So, I just got my turbo back from my pal Ruben at SoCal Porting (does good work fast and inexpensive) and, I have a question about the exhaust housing with the EBPV.
Is there a gasket that goes between the turbine housing and the adapter that the down pipe mounts to? And, if so, what is the part number for it? If it's steel to steel cool. If not, I'd prefer to put the OEM gasket in there versus permatex or something similar.
Pic of the compressor housing with a little port work....
Ford - Explorer :: Chirping Noise Coming From Bell Housing?
Getting a chirping noise coming from (i think) the bell housing. a few small chirps at start up, then constant after about 1300rpm, eventually gets high enough and drowns out behind the exhaust that i cant hear it.
Possible flywheel issue? I've uploaded a video to try and illustrate the issue. 1996 ford explorer XLT 4.0.
Just replaced starter a few weeks ago, but this problem was happening before. I dont know if it was as prominent and got worse, or if im just now noticing it and focusing on it.
1996 Ford Explorer bell housing chirp. Flywheel? - YouTube
Ford Excursion :: Trans Fluid Leaking Out Of Bell Housing Onto Y-Pipe / Smoke Coming From Under The Hood
A little background info...up until about 6 months ago my 01 Ex V10 was a grocery getter for the wife; only got a few thousand miles a year for the most part. Since we moved from Washington state to Texas it has turned into my daily driver (after a 2500 mile drive towing 8k trailer).
A couple of weeks ago we were running errands and after we got home there was smoke coming from under the hood, but I couldn't pin point it. I let it be because I figure it would let me know when something was really wrong. A few days later it did it again but this time I found the problem; transmission fluid was leaking out of the bell housing onto the y-pipe. I did my research and come to find out it is most likely the front pump seal that got soft from overheating. So my buddy and I drop the transmission and replace the seal. Put it all back together and everything seems great.
Another week goes by and we have driven the Ex fairly extensively around town and even took a couple short day trips and everything is great. Then as we are turning onto an on ramp to get on the highway I give it gas to speed up and all of a sudden the RPMs climb like it dropped into neutral. I had enough momentum that I got over onto the shoulder and started to check thing under the hood. Looked like I was low on trans fluid; ok so I added a quart. Put it in "D" and still nothing. Then I try "1", "2", "R" and they all work fine.
Ford F-150 - 1997-2003 :: Coolant Leak From Bell Housing?
Only when running heat or defrost, coolant leak looks like it's coming out of the bell housing. I have a supercharger so very difficult to see behind motor, but with inspection camera, heater hose lines look dry. firewall looks dry. No coolant in cab. No steam on windows or smell. Pretty sure not casting/ freeze plugs because absolutely no leaking with heat off. Can run for days with no loss, then turn on heat and within minutes/ seconds coolant puddling in driveway. Is the hose that runs through valley pressurized only when heat is on? I saw a few older threads but as far as I could tell none specified heat on/ heat off conditions. Just started problem after doing some other work, hoses were off radiator and intercooler, replaced radiator. None of those connections are the culprit.
98 F150 Lariat 1900 TVS S/C Chiller Killer I/C 19PSI Snow performance WMI
Ford F-150 - 1997-2003 :: 1998 - Separating Engine From Bell Housing
Removing 4.6 triton from 1998 F-150. Is there a way to remove the top 2 screws connecting the engine to the bell housing without removing the intake manifold? Although I don't mind removing the intake, I am doing a 4.6 to 5.4 swap and would rather attach the intake prior to putting the 5.4L back in. Figuring if I cant get it out that way though, I wont be able to put it back that way.
View 4 RepliesCamry :: 1994 - Leaking Anti Freeze From Weep Hole
I have a 94 Camry left to me by my father inlaw when he died a year ago. I notice antifreeze coming from a weep hole just above one of the alternator mounting brackets. Whats involved with replacing the water pump and timing belt? Im guessing thats what it is and while I am in there I will replace the timing belt as I dont believe either have been replaced. The car has about 160,000 miles on it. I kept my Windstar going for about 250,000 miles before my daughter wrapped it around a tree so Im sure its something I can handle. The problem is time as we are getting into winter. Is it a major job or something that can be done in a few hours?
View 5 RepliesFord Super Duty (1999-2016) :: 2014 F250 6R140 Transmission Leaking At Bell Housing
New to me truck has 80k on it, it's leaking at the bell housing. Pulled the inspection plate and it's definitely red stinky automatic transmission fluid. Back of the torque converter is clean.
Ford warranty has run out, however I do have an aftermarket warranty on the truck. Trans temp isn't above normal or running hot.
I'm a very mechanically inclined engineer, I do not work on cars for a living, but I have replaced an input shaft seal on a 4wd transmission before. That's my best guess as to what's leaking. Is this a common issue?
Ford 7.3L Power Stroke (1999-2003) :: Rounded Off Thermostat Housing Bolts
Tried to flush it and got as far as draining everything. I can't hook up my T and begin the flushing process because I can't remove the thermostat. I have a buddy who can get the bolt out but I'd have to be able to drive the truck to him. I've tried just about everything to remove it. I did manage to find some replacements for when I do get the last one out though .Is there a way to still flush this thing like maybe just hook up the hose to the t and run the engine with the heat on to open the thermostat?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Compressor Wheel For Ported Housing
Was wondering if the wheel for the ported housing from riffraff is worth it. Also, since I'm lazy I was gonna just spin the old wheel off with an impact wrench. I have a cordless that's prett stout but I'm sure I'll have to use air. Any thoughts on the wheel and taking the stocker off this way?
View 14 RepliesFord Super Duty (1999-2016) :: 6.4L - Oil Leak From Rectangular Rubber Grommet On The Front Of Transmission Bell Housing?
Noticed a small oil spot on my drive way where i park my truck the other day. Got up underneath and saw it was leaking from a rectangular rubber grommet on the front of the transmission bell housing.
What could be causing this? Have heard a few different things, turbo line leak, turbo pedistals, HPOP leak. Seeing what Super Duty Nation thought of the problem. Going to the dealer sometime this week.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Leaking Diesel From Fan Housing?
I'm presently traveling and my '02 F-250 with a 7.3 PowerStroke has developed a pretty steady drip of what I am almost sure is diesel fuel. It's dripping from the very front, from the shroud around the fan and radiator area.
I have some basic tools with me, but no experience on this engine or the fuel system. Does the fuel line go up into the radiator area? What should I be looking for? I'm stranded in a campground until I figure this out.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Fuel Filter Housing Leaking?
I have a 2001 f250 7.3l 4x4 and the fuel filter housing is leaking real bad from either the back or under it. I need to get info on parts that i would need as well.
[URL]....
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Slow Tap Sound Coming From Engine
My 2002 7.3 engine makes a slow tap sound...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Grey Smoke Coming Out While Driving
I didn't notice anything until I was towing yesterday and tried to pass a car to get onto the offramp.
Anyway, I went to floor it so I could get around and, in my mirror, I could see a decent bit of grey smoke coming out. What could it be?
It doesn't smoke at all on startup and runs smooth right away.