Ford 6.0L Power Stroke Diesel :: How To Diagnose And Replace A Bent Push Rod
I had an huge amount of work done to my 2004 Excursion (early model 6.0) earlier this year. ARP studs, new HPOP, ICP, IPR, Ford lifters, Ford push rods, EGR delete, Bulletproof remote oil cooler and filter, EBP sensor and tube, Ford head gaskets, and a bunch of other stuff including eventually a new FICM (not Ford) and a new 140 Amp alternator.
My problem is it sounds to me like some sort of metallic tapping is going on and it doesn't feel as smooth as I would expect -- like a very soft miss. Currently the tech says that there are no "low contributing cylinders". I am wondering if there may be a slightly bent push rod? He is adamant that a bent push rod won't stay where it is supposed to -- I say it depends on how bent it is. I am also worried that a rocker arm may be bent or deformed in some way.
My question is this; Once the valve covers come off -- if nothing looks wildly wrong, where do I begin to confirm that I do not have bent push rods or damaged rocker arms? He says that in order to check the push rods we would have to remove head bolts off of the rocker arms (I think I have that right). But he said we run the risk of compromising the head gaskets if we touch anything like that. If we have to remove head bolts (stud nuts for me?) can you take one rocker arm loose, check that rocker arm and push rod, and put it back together safely? Without having to pull it all the way down and put new head gaskets, etc? That would mean releasing the clamping pressure across both heads at each rocker arm -- is that creating the potential for blown head gaskets?
I know in my youth we would roll push rods on a sheet of glass (12" X 12") because glass is supposed to be flat -- can't bend it or deform it without breaking it first. I assume that still works. I now have a Scan Gauge II but it is not set up yet to check all of the readings for the sensors. I also believe I need to check for leaks with simple green and to make sure I don't have any exhaust leaks. But what about the push rod/rocker arm question? Is there another way to verify integrity?
Ford 6.7L Power Stroke Diesel :: Transmission Shudder When Push The Throttle In 2nd / 3rd Gear
I have already logged 6K miles on her, crazy, but it's my job. I have pulled 5 maybe 6 trailers (form trailers, about 15K pounds loaded, this time of year). Loaded or unloaded, when I push the throttle in 2nd, 3rd gear, I feel a shudder, like transmission shudder.I know this thing throws down 800 ft. lbs. of torque, should I not be pushing it so hard? Or, what am I feeling?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Traction Control Turn Off And Stay Off When Push The Button?
Does the traction control turn off and stay off when you push the button? I read an owners manual and the way it is written makes me wonder. It makes it sound like the traction control reengages when you put the truck in reverse. Even when you had it turned off.
What are the facts? What is the real difference between an F350 SRW at 11,200 or 11,500 GVW and one with the 10,000 GVW. Is it just paperwork or do they change springs?
Ford 6.0L Power Stroke Diesel :: 2003 - Engine Stumbles When Push Door Unlock
'03 Excusion 6.0psd....new batteries a year ago, new starter a month ago, head gaskets etc a year ago....
Today I go out and start it up, no problem. Gather up the kids and head out to load up. When I climb in, I hit the unlock button to make sure the kid's doors are open and the engine stumbles.
I thought maybe I was imagining things so I hit it again and the same thing happened but it died but fired right back up. Drove the kids to school and it ran fine, no problems.
Ford 6.7L Power Stroke Diesel :: Washer Fluid Cutting Out Or Not Even Working When Push The Button
1993 ford ranger ... Having issues with washer fluid not working. Mine has started cutting out or not even working when I push the button. But if bang it on the end of the handle with something hard it will work just long enough to clean the salt off the window.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Removing Block Plug - Installing Heating Rod?
Has actually removed the block plug (from where ever it is) and installed a heating rod...I'm fairly mechanical, just not sure of the steps or tools needed.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Removing Transmission Cooler Lines?
06 6.0 How do I remove the trans cooler lines from under the truck? I've got the lines hanging free they're unscrewed from the transmission and trans filter but I can't seem to snake them out to replace them. How is this accomplished?
View 7 RepliesFord 6.7L Power Stroke Diesel :: 2014 - Removing Glow Plug Harness?
I'm really struggling to get this sucker off my 2014 6.7 F350
it says in the ford manual to lift the plastic tabs then pull off, I did that easily with 3 on each side, but the end plug on each side (the one closest to the windshield) does not seem to have a liftable tab (it looks different to the others as its at the end of the cable)
I've almost broken it but not quite, its over $300 for new harness, ouch
I do have the odd little hook tool they sell for this, it worked with the other 3 for sure, but I've spent ages on the 4th on each side and cannot budge either of them
Ford 6.0L Power Stroke Diesel :: Lost Some Power / Leaking Head Gasket
My 2004 6.0 has lost some power and the head gasket is leaking into the coolant. How long can i continue to drive the truck before too much damage is done to the engine?
View 10 RepliesFord 6.0L Power Stroke Diesel :: Head Gasket Replacement?
So, I blew my head gasket and have been looking for what to replace it with. From what I've seen, just an OEM gasket would be best.? I'm also putting ARP studs in it, unless there's another brand I should put in it.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Possible Blown Head Gasket?
Truck is a 2006 F-350 6.0, ARP studs, Ford Head Gaskets, Bullet Proof Diesel Oil Cooler Kit and EGR with an SCT tuner on tow mode.
Towing approx 15,000 pounds noticed truck started to lose power and misfire. Pulled over and noticed engine oil all over the driver side on engine, looks like it sprayed to top of engine as well. Oil on valve cover, FICM, exhaust manifold. I looked under the truck and saw that oil is all over bottom of the truck, differential covered in oil as well. Looks like blue smoke coming from tailpipe and smells of oil burning. Cannot tell where oil originated from.
I removed the EGR Valve, to see if there was moisture on the valve and when I looked into the intake manifold there is engine oil pooled in the bottom of the intake manifold and on the EGR Valve.
This is not dirty water from soot, it is oil. Truck is misfiring, with no codes being thrown. I noticed a small amount of white residue around the radiator cap however I had just filled up the reservoir, week prior. I unfortunately do not have gauges in the truck and rely on the factory gauges; coolant temps did not rise or move at all when this happened. I am not sure if I blew a head gasket, and really confused on how engine oil got into the intake manifold. I ran the engine with the air filter removed and can see blue smoke coming out of the CCV and oil in residue in front of the turbo inlet.
Ford 6.0L Power Stroke Diesel :: Head Stud Installation?
I Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
Ford 6.0L Power Stroke Diesel :: Dimensions Of Head Surface?
Any head handy that they could measure for me (or head gasket)? Wondering what the dimensions of the head surface is.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Head Gaskets Blown?
If you have a blown head gasket on a 6.0, after the gaskets were removed would you be able to tell where the gasket failed?
Since the gaskets are metal or multilayer metal in some cases would you be unable to tell where the gasket failed or would it always be visible?
Ford 6.0L Power Stroke Diesel :: Every Now And Then Fuel Gauge Will Go To E After New Head Gaskets
I just had headgaskets (oem) studs, egr delete,oil cooler done on my 06 plus water pump cause the gasket blew. I have a sct livewire hooked up monitoring everything and tonight i noticed that the eot and ect's were way off. fully warmed up and rolling 65 Anywhere from 40*-50* out it was eot-156 and ect-172. Degas bottle was at the normal level.
I am also having issues with the fuel gauge. Every now and then the gauge will go to E and the miles to E will display ---. Turn the truck off and back on it works again. I am half assuming its the plug on the sending unit or the sending unit itself.
Ford 6.0L Power Stroke Diesel :: 2004 - No Start After Head Replacement
So I'll give a little history. Had blown head gaskets so I tackled that got it back together and now I can't get it to start. I have a monitor but it won't tell me if I have ficm sync. I have 1500 psi cop reading. I have spinning it over far 15 to 20 minutes. I'm using a bluetooth scanner and a app on my phone. I have no codes thrown or anything else. Do I keep cranking on it or am i missing something.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Did Head Gaskets Now Lights Won't Working?
I just pulled the cab and did headgaskets, studs. I put everything back together and when I turn the key, nothing, no lights, zero.
I've checked all connections and batteries are good, checked all fuses, where to start with this?
Ford 6.0L Power Stroke Diesel :: ARP Studs And OEM Head Gaskets Failures
So I am just wrapping up getting my head gaskets done for the second time. Last time was 7 yrs ago. Truck now has 90K mi on it and I have had nothing but Matt's tunes on it since the head gaskets were done originally. I have only towed once and I put the 8K tow tune on for that trip.
ARP studs were used but heads were not decked then. OEM gaskets, done by Ford.
So a head gasket failures with ARP studs and doing everything else the FTE way?
New heads are decked and o-ringed. Planning to go a little more gentle with the tuning, but don't really want to. Driving it stock just sucks.
Ford 6.0L Power Stroke Diesel :: Won't Start After Replacing Head Gaskets
Ran fine, did the head gaskets ,egr delete, oil cooler and 12mm dummy plugs. Primed the fuel system, oil pressure looks good on the guage , spins fine but doesn't seem to be making any attempt at starting . Gave it a shot of quick start and it never so much as kicked. Everything looks good, nothing leaking and nothing obvious. To top it off we are without power after Hurricane Mathew left his mark.
View 14 Replies