Ford 6.0L Power Stroke Diesel :: Check Gauges Light On And Trans Temp Gauge Pegged On Hot
Driving my 2003 today seen the "check gages" light on and the trans temp gage pegged on hot. CRAP, tranny time! look at the edge evo and it reads trans temp as -60F ???. Plugged in the torque pro and it reads 8,240F. At that point I figure its PROBABLY not that hot. Let it sit for a while and back to normal. Watch trans temp on torque pro as I drive it and everything is fine till it gets to about 150, then it jumps to 60F, then 30F, the 8240F. The cooler lines and trans pan are both feel normal. Picked up a new temp sender on my way home.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Oil And Water Reading Climbed About 15 Above Optimum Temp On SG?
The oil and water readings on my SG have been gradually climbing for the last few year to where they are about 15* above the ambient temperature after sitting over night. My question is could the values for the other readings be getting high. For instance going down the road at 65mph my ICP was 1250 and my IPR was 62.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Fuel Pressure Gauge Is Reading Dead 0
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Check Gauge Light Coming On And Tow Haul Light Flashing
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Check Gauge Light Came On And Tow Haul Light Started Flashing
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
Ford 6.7L Power Stroke Diesel :: Check Engine Light And Funky Boost Gauge
Noticed the other day when I went to leave a job site my Check Engine Light came on but the truck started fine and seemed to run normal. while cruising down the highway I noticed that my factory boost gauge was showing 35psi and fluctuating between that and around 10. looking at my H&S it was showing normal boost readings for the current driving condition, when I came to a stop the H&S would show 0psi but the factory one would fluctuate between 0 and 35-40psi..
I can tell the turbo is not spooling at all during this time. if I take off from a stop with the gauge showing 35 the engine sounds louder than normal at first take off compared to when the gauge is reading normal. I haven't gotten a change to get it in my shop yet to look it over but does the dash gauge read from a different sensor that what my H&S is reading? Truck is an '11 F250, deleted both EGR and DPF with H&S tuner. I checked codes and all I have is P06A7. Where to start?
Ford 6.0L Power Stroke Diesel :: 2004 - Check Gauge Light On While Going Downhill Towing?
My 04 F 350 started with a check gauge light while going down hill towing an 18 ft car hauler full of mulch. Did it for 5 seconds, then when we got to our land and I was getting ready to back up it did it again. and this time my oil pressure gauge was at zero. I shut her down. checked the oil. its full. Drive home everything is good. Today I'm getting fuel pressure gauge going nuts. 80 to 100 PSI. at idle no oil pressure and the check gauge light. but the engine is still running. Oil was changed 4K ago. fuel filters same. Where to start looking?
View 5 RepliesJeep - Overheating :: 2006 / 3.7L - Temp Gauge On Dash Reading High When Driving
I have a 2006 Jeep Liberty 3.7L that has a temperature gauge on the dash that reads an overheat when driving. The oil looks normal, there is no white smoke, no bubbling from reservoir. I have replaced the following:
Radiator
Thermostat
Water Pump
Coolant Temperature Sensor
Coolant Reservoir Tank
I am not leaking any coolant and the reservoir level has been fine. I have let the vehicle idle for 20+minutes, with no overheat. When I drive it around, the temperature gauge will read an overheat. When I stop the car and pop the hood, the engine is not overheated and both rubber hoses to/from radiator are flowing the coolant. The only thing that will bring the gauge down is turning on the heater full blast. Could this be the gauge itself being bad? Could it be a short in a wire somewhere? I had thought maybe a head gasket, but have no symptoms of a head gasket.
Ford 6.7L Power Stroke Diesel :: Check Engine Light Came On / Code P0181 Fuel Temp Sensor
Just over 6000 miles....Yesterday morning the light came on. Dealer wouldn't look at it for a week. Went to my mechanic this morning to check the code it was p0181 fuel temp sensor. I read something online about the block heater making it too warm. The other night it was cold so I plugged it in, then yesterday morning it got warm overnight like into the lower 40s. I noticed the grill felt warm too. My mechanic cleared it if it comes back on do I have an issue? Is it ok to drive?
View 14 RepliesFord Excursion :: No Reading At Oil Gauge And Temp Light Is On When Very Cold
I have a 2001 Excursion Limited V10. 146000 miles 2 wheel drive. I have had it about a year and this is my first winter to really have experience with her.
When the outside temperature is very cold and the engine is cold from sitting all night, at start up, the oil pressure gauge reads nothing and the oil pressure/temp idiot light is on. Only does this during the first very cold start up or after sitting and engine getting very cold again.
I can drive just a short distance (2 blocks) and both gauge and light go to normal and stay there for the rest of my drive. I am using a quality 5/20 oil and filter and the level is good. Warmer days it has never happened. Truck runs fine, smooth idle, no "limp mode". She has not had any recent work done. All the other dash gauges read fine.
There is something about really cold temperatures that have to be causing the issue , I think. ??
Ford 6.0L Power Stroke Diesel :: 2004 - Engine Coolant Temp Gauge Does Not Work
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Hot No Start - Temp Gauge Maxed Out
So I recently bought a '04 F-250 early build with the 6.0 powerstroke. Truck drove fine for the first 1000 miles. Drove from Fort Hood back home for leave. Got home and truck sat for two days, started it up and it ran for 15 minutes, then shut off on me. Temp gauge read normal, but after it shut off, I turned the key off and back on and temp gauge was maxed out. And truck has to cool down before it will start again. Replaced the IPR Sensor to no luck. Not sure if I have an ICP sensor issue or what it could be.
View 11 RepliesFord 6.7L Power Stroke Diesel :: How To Get Ambient Temp To Read On Dash Display
New 2015 King Ranch. Has the navigation screen where it displays the outside temp. Just watched a youtube video where another 6.7 truck had their ambient temp displayed on the dash screen between the speedo and RPM gauges.
Also going under "gauge mode", it shows tranny and engine oil temp, move over one position it shows compass, and move over third, it shows nothing. What this third position is supposed to be for?
Ford 6.0L Power Stroke Diesel :: Cooling System / Temp Gauge Started To Rise Past Normal Before Fan Comes On
I have a 2007 6.0 that this has happened to twice now. It's fine around town but I never hear the can come on. Friday when on the interstate my my temp gauge started to rise past normal operating temperature before fan came on. Is this normal? After the fan came on it stayed at normal temp for the rest of trip....
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Transmission Temp Gauge Dropped / Tow Haul Began Flashing
Okay so I just peaked 100k and (of course) my 6.0 has an issue. I was driving along when suddenly my Transmission Temp gauge dropped to nothing, the tow haul began flashing and my check engine light came on. My transmission hard shifted and wouldn't shift up from 3rd. I let the truck sit for a few days, no leaking was observed and no blown lines. I added 4qts of tranny fluid and went to take it for a spin. The truck did fine for about 20 minutes and the same issue occurred. I parked it and checked the dip stick and it was full. What could the issue be.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Way To Check Batteries Health With OBD2 Gauge?
Is there a way to check to see battery health with Dashboss? I know I can check charging system, but is there a way to monitor if the batteries themselves are going south on me?
View 5 RepliesFord 6.7L Power Stroke Diesel :: Truck Making A Lot Of Noise When Tried To Accelerate - Boost Gauge On Dash Stuck At 35 PSI
Was driving back home from shopping tonight and my truck was making a lot of noise when I tried to accelerate. I noticed the boost gauge on the dash was stuck at 35psi but the MiniMaxx showed 0psi.
No engine light so I babied it home which was about 30mins driving and managed to accelerate slowly to avoid the engine rattling. I didn't want to shut it down and restart in case it wouldn't start again for some reason.
When I got home I idled until EGT was <300F like I normally do (it never went over 700F when I was driving home) and then restarted it. The gauges worked fine, MiniMax showed boost and the engine revved freely with no rattling noise. I haven't taken it out for a road test, I'll do that when it's daylight.
Bad sensor somewhere? I would think if the turbo had failed it wouldn't have been fine after a restart.
Ford Aerostar :: 1994 - Temp Gauge Reading Low?
It is a garage queen 1994 4.0 AWD with 42,000 miles in nearly perfect shape. Except for the dent in the rear on the passenger side.
I have posted a picture of the dash when going down the road. As you see the engine light is on. It comes on intermittently, pulled the codes, indicated MAF, 02 sensor, running lean/rich. Runs like a champ, no hesitation, still gets up and goes, gets the appropriate gas mileage. I replaced the 02 sensor with the original Ford Part. Didn't cause the engine light to stop going on after about 20 to 60 minutes driving, sometimes it doesn't come on at all.
Could this thermostat be running too cool and causing the engine to throw those codes? Would gladly take it to a mechanic, but seems like it might be a fishing trip with my dollars for them. Next I was going to replace the MAS myself, easily done with the original remanufactured part at a cost of 150.00, 70 for the core, but don't want to chase my tail with these engine lights on when it runs nearly perfect.
Have sprayed the MAF. Checked for air leaks anywhere. Done all the things I could do by just lifting the hood.
So the picture shows the Temp gauge barely touching the N flying down the road at 70 on a level surface, outside temp about 60. Reading the posts says they all run in the cool section of the temp gauge.
So the question is, do they run this cool? Heater works fine and the gauge goes up past the N resting before the O when going up hills on the way to Tahoe. Is this a thermostat problem on a 20 year vehicle with low mileage, or am I going to have to bite the bullet and let the mechanic go wandering through the vehicle?
Santa Fe (CM - 2007-12) :: Fuel Gauge Not Reading Correctly And Check Engine Light On
I have a 2007 Sante Fe with the 3.3 engine. Having a problem with the Fuel gauge not reading correctly and a check engine light. The engine code indicated that the problem was with the sending unit in the tank on the "A" side (behind the driver). I checked with Hyundai and with a tech line service and they indicated that it was a common problem and I needed to replace both the "A" & "B" units to correct the problem. I did that and cleared the codes and it set another code indicating that the "B" unit was the source of the code. I pulled the "B" unit again and checked the wiring and the problem still was there. I switched out the units on the "B" side again with the old unit and the problem is still there.
View 4 Replies