Ford 6.0L Power Stroke Diesel :: Oil And Water Reading Climbed About 15 Above Optimum Temp On SG?
The oil and water readings on my SG have been gradually climbing for the last few year to where they are about 15* above the ambient temperature after sitting over night. My question is could the values for the other readings be getting high. For instance going down the road at 65mph my ICP was 1250 and my IPR was 62.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Powerless And Rough Idle Until Reaches To Running Temp
I have a 05 6.0l. Egr deleted. And my truck has a rough idle and power loss. Ive tested the ipr and the icp and they are reading at specs. I've also replaced the Hpop about 1500 miles ago. It has a real rough idle until it's at running temp. And it has power loss, I'll be driving down road and theres no where near has much power has there should be. And the idle will jump between 1500 rpm and 2000rpm.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Rough Idle And Dies / No Power
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 Very Rough Idle When Cold
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean .... It's 98* on a cool day , when "cold" I mean just started for many hours.
View 13 RepliesFord 6.7L Power Stroke Diesel :: Optimum Gear Ratio For DRW - 3.73 Or 3.55?
I got burned with a smoker back in the mid 1980's and have been hesitant to come back. I am currently pulling my 5er and my enclosed gooseneck with a 6.2 gasser SRW. It has the 3.73 gears in it...not the best for towing.
I am thinking about ordering a new SD DRW 2wd with the 6.7 PSD.
Both my trailers are rated at 18000 GVW, what would be the best ratio to order? 3.73's?? 3.55? Fuel mileage will be what it will be with what ever ratio I go with. The truck will be mainly a puller. Not a daily driver.
Ford 6.0L Power Stroke Diesel :: 2007 - No Power / Dies Once Up To Temp But Restarts Fine
I have an 07 6.0 diesel and I'm having trouble once it gets hot. It begins to lose throttle response and shakes while cruising and also has a rough idle. sometimes it dies while idling but after cooling off for a few minutes starts back up and runs fine. I've checked the high pressure oil and the ficm and both of those are fine. I've done an EGR delete so it has nothing to do with that either. My MPG also goes way down when this happens.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2004 - After Start Up Rough Idle And Power Lag?
Have a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Rough Idle - No Power?
I recently bought a 2004 6.0 extended cab truck. It has 223,000 miles on it and has been running great. Bought it here in Arkansas where I live and recently drove it to Texas and back after having just put some Hot Shot oil treatment cleaner in it. I ran it the 1000 miles as it suggests. Just the other day as it was hitting the 1000 mile mark the truck started to lunge/runaway and stalled. I finally got it back home and started looking into the issue. Based on what it was doing, (lunging/running away, and at idle in park random burst of rpms and then dying after doing it a few times), I started to do some research. Most of the answers I found claimed it was the IPR valve. I found that the IPR valve is supposed to, as claimed by some, be pulled and inspected every 100,000 miles are so and if need be replaced or the rebuild kit gotten for it. So I decided to just replace it as well as the oil, oil filter and fuel filters.
When replacing the IPR valve I noticed that it was original and that its screen was missing. I didn't have any problem moving the little piston in the center of the shaft with a small bolt however that doesn't really mean that it isn't bad. I tried a magnet to see if the screen was still in there and nothing came out. I did not try using a camera as I do not currently have one, to look inside the port to see if I saw it. After replacing the IPR valve with a brand new one and changing the oil I started the truck. It seemed to be running a little ruff so I let it warm up. Not one minute later the exact same thing started happening, lunging/running away (random increase and decrease in rpms), so I called it a night. The next morning I decided to change the fuel filters. No that it matters the order in which I did it, but I changed the top end filter first and the the one on the frame with the dealer recommended OEM filters as was the case with the oil. I did find in the filter on the frame that there was a small amount of sand and clay soil looking matter in the filter. I did clean out the filter housing as well.
After replacing the filters I started the truck to warm it up. I noticed that it was still running a little ruff but no random, lunging/running away (random increase and decrease in rpms). However after five minutes it started coming back. I finished letting the truck warm up and took it for a drive. Got it up to between 7-80mph for about 15 miles to try and see if I could "blow out" whatever may be in the fuel if that was even an issue I do not know. The truck seemed to get more power and run a little more smoothly so I stopped at my buddies house not to far from where I was and let it idle. No issues other than a little ruff idle. After about 10min I took off towards home doing similar speeds. I noticed at a little over 2000rpms that the truck was shaking a little but so I dropped the speed down. When I got home not more than one min after idling the same issue, lunging/running away (random increase and decrease in rpms), started happening again.
At this point I took back to the interwebs and came across a post that said the ICP might be bad and does cause this issue, lunging/running away (random increase and decrease in rpms). However I also noticed that this is a huge debate as to whether or not the ICP can cause this. Ford master mechanics say no and other mechanics say yes and round and round it goes. I decided to do the simple test many recommended which was to simply unplug the ICP and see if anything changes. Things did change. No more lunging/running away (random increase and decrease in rpms). Not more than two minutes after plugging it back in, allowing the computer to account for it now, the lunging/running away (random increase and decrease in rpms) came back. In the middle of it doing this I unplugged it and that went away. So needless to say I replaced the ICP and voila the lunging/running away (random increase and decrease in rpms) is gone but the ruff idle is still there along with a slight loss of power.
To answer some questions:
1. The oil and water are not mixing so I am almost positive that the heads are fine
2. The intercooler couplings are leaking a bit. I have ordered the new ones and will replace them as soon as they come in. Can this cause the issue?
3. I am blowing no white or black smoke except for when the lunging/running away (random increase and decrease in rpms) issue was present and the truck almost died. It would knock occasionally when it almost died and would send a slight puff of black smoke which I assume is a low or high fuel issue from the truck trying to die
4. I have not had the no start issue at all
5. I did not see any debris in the oil during the oil change
6. I didn't do the air test on the ICP port as I do not have the adapter.
7. The only code I got on the IBD II port was when I unplugged the ICP which was to be expected
8. I found no damaged wires
I am at the point where I am wanting to take it to ford to have them run a diagnostic on it but am wondering if there is anything else I need to be looking for. Here are a few questions I have.
1. Does this sound like a bad injector? (When I bought the truck it would sound like a misfire or ruff idle condition was present for about 5-15 seconds and then it would smooth out with no issues. It would run a little ruff if you tried to take off without letting it warm up, which I did once or twice and low rpms, but when it warmed up no issues were present).
2. Could this be the HPOP?
3. Could this be the FCIM? (The previous owner had replaced the FCIM not to long ago with one from Ford I believe. Said it cost him something like $700)
4. Could this be something clogging the oil screen under the manifold?
My final question right now is do any of you know where or what brand OBD II reader or software I can get for a decent price that will tell me the voltage of each injector and FCIM is without me having to go to Ford to get it looked at.
Ford 6.7L Power Stroke Diesel :: 2011 - Rough Idle - Surging And Loss Of Power?
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...
Ford 6.0L Power Stroke Diesel :: 2005 - Rough Idle - No Power - Black Smoke?
05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.
This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....
Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.
However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine
Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.
Ford 6.0L Power Stroke Diesel :: E350 Dying When In Gear / Lack Of Power / Rough Idle
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Rough Idle At Startup And Shaking - Lag In Power And Vibrate On Highway
This morning I noticed when I started the truck had a rough idle shaking truck. The truck felt weak. Boost would go up but truck felt like it was in sand. While coasting on the highway at 50-55mph the truck not only lags in power but vibrates viciously until the overdrive kicks in that vibrations in cab and ssteering wheel go away.. What might be going on?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Slight Miss / Rough Idle / Loss Of Power
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 V8 - Hard Start / Rough Idle / Shaking - No Power When Cold
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
Ford 6.0L Power Stroke Diesel :: Intake Air Temp Sensor One Circuit High And Strange Idle?
I have a code for iat sensor 1 circuit high. It's the only code I can pull. I replaced the sensor in the manifold and still no change. The truck revs up when started but kinda finds its idle rpm after a second and the idle fluctuates some when the truck is warmed up too. I have a snap on solus and all parameters seem to be good. Icp sensor is also new thinking it might be the cause. Other than that the truck runs perfect and doesn't miss a beat.
View 14 RepliesFord 6.0L Power Stroke Diesel :: IPR Value And Intermittent Rough Idle
My IPR value on torque pro koeo is at 14.7. Is that normal? Usually idles around 23.7-24 but when I experience a slight rough idle IPR will be 26-27. When I was under the truck last week I did see there's been oil leaking somewhere seems leaving evidence on the drivers side rear of bellhousing. Any relation?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Sluggish Around 35 MPH Till Full Throttle
2003 f250 6.0.... recently did oil cooler,hpop,ipr,icp,fuel pump,egr valve, rebuilt the turbo.... when around 35mph truck seems sluggish and doesnt seem to pick up quick untill i floor it an then hauls butt.. vgt reading at idle is 62% and when floored around 30 to 35%.. fuel pressure is 63psi.. ipr is around 60 to 70% when floored and around 25% at idle. Hpop reading when floored is 3000 to 4000psi and idle is 624psi....
View 14 RepliesFord 6.0L Power Stroke Diesel :: Rough Idle - FICM Is At The Start Of Going Out?
So after replacing all injectors, I was getting a rough idle and drive. Got an imbalance on 5 & 4. Cleared out codes and 5 still showed. The guy doing my work and I couldn't trace it to anything so we thought well maybe we got a bad one. Did fail the buzz test. So got a warranty one and put in. Wouldn't you know it's still not running quite right. Only thing we can think of is maybe the ficm is at the start of going out. Voltage reads good still though. Staying constant at 47/48. Is more noticeable to run rough when starting from cold then smooths out but you can still make out/feel an injector going in and out.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Intermittent Rough Running At Idle
In your experience, what issues have you seen that caused intermittent rough running at idle, but did not throw a code. I have monitored (with numerous scanners/gauges) this 6.0, but cannot get a code or see any of the sensors out of spec.
At Hot idle:
IPR: 24.2
ICP: 640
ICV: 0.90
MAP: 14.7
MAF Volts: 1.5
EOT/ECT Deltas within 10 and Avg ECT=192, EOT=199
EGR Valve cleaned and EGR demanded = EGR Measured
Vehicle will run rough after long runs or towing. Cylinder Balance test showed all injectors on. What could be the cause?