Ford 7.3L Power Stroke (1999-2003) :: Ignition Lock Cylinder Removal With No Key
So I have a replacement steering column for my truck and need to swap out lock cylinders. My question is; since there is NO key, is there any way to avoid drilling out retaining pin. If I did drill it out am I entirely screwed'?
View 14 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Ignition Lock Cylinder Removal
I bought my 2000 F-250 CCSB a while ago and it came with 2 keys - one for the ignition, and one for the doors/tailgate - may not seem like a big deal, but it annoys me to no end.
From my understanding, the truck had previously been stolen and had the driver's side lock punched, and then something happened to the ignition lock to where it had to be replaced - hence the different key. I finally got around to replacing all the locks so that I'd only have one key. I started with the doors, then moved to the ignition (which I thought would be the easy part). I've replaced several cylinders before and I know it should be simple, but for the life of me I can't get the cylinder out!
I push the detent, turn the key to run, wiggle and pull.... nothing. I can feel the detent push in, and the cylinder will move a little, but it won't come out. I'm not sure if this is something that just happens sometimes and there's a fix for it, or if I'm in a unique circumstance and my column was somehow damaged during the theft and that's what's causing it.
Jeep - Cherokee :: 2000 - Ignition Lock Cylinder / Can't Get Key Unlocked
I have tried all the tricks on the internet and still can't get the key unlocked, so I am ready to just replace the part. Is this something my son can do or is it very complicated?
View 1 RepliesImpala - Chevrolet :: 2004 - Ignition Lock Cylinder Missing
I have an impala with a missing ignition lock cylinder. How to bypass the security with this component missing or know where to find the wiring schematic for this model. Every schematic I've found on the web aren't complete circuits.
View 5 RepliesSanta FE SM (2001-06) :: 2003 - Ignition Lock Cylinder Removal
A few days ago my ignition key would not budge when I tried to start my 2003 Santa Fe. I tried all the tricks like turning the wheel. dry lube, etc but no luck. All indications are that I need a new ignition lock cylinder but I can't figure out how to remove it. I removed all of the plastic and metal shrouding below the dash but can't seem to find a hole to release the cylinder. I have also tried to remove the whole cylinder body assembly by disconnecting the wires and loosening the bolt that secures the "arm" from the ignition cylinder body to the steering column but that also seems to be secured in a way I can't figure out.
View 3 RepliesFord F-150 (2004-2008) :: Remove Ignition Lock Cylinder?
How do I remove ignition lock cylinder to take and get new set up?
View 4 RepliesFord Escape / Hybrid :: 2003 - Ignition Lock Cylinder Replacement
I'm replacing the ignition lock cylinder on my 03 Escape. The factory cylinder has the little black "wings" that nestle around the key when inserted:
The locksmith says the replacement cylinder needs to have those same wings for him to be change it. Is this correct? The auto part stores have the regular cylinder (with no wings) readily available, but the one with wings is a special-order item and I need this sooner rather than later.
Plus, the wingless one includes keys while the other appears to have none.
Ford Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Pontiac - Grandam :: 2000 - Replaced Key Lock Cylinder Now Beeps As Key Left In Ignition?
I replaced the ignition key lock cylinder on my 2000 Pontiac Grand Am SE. I performed the re-learn process by cranking the engine over, then releasing to the ON position for about 9 minutes. During the 9 minutes the SECURITY light blinked the whole time, then at the end it went solid for a few seconds, then off. On the next cranking cycle I was able to start the engine and thought all was good. But now when I open the door the car beeps as if the key is left in the ignition and the automatic locks are disabled with the door opened.What is the problem and how do I fix it?
View 1 RepliesFord - Explorer :: 2002 - Ignition Lock Replacement?
Lock cylinder needs replacing. Was stuck in the off position and would not rotate. Finally freed it up so I can remove the cylinder.
Question is, will the key that comes with the new cylinder need to be programed. If so how is this done?
Ford - Explorer :: Ignition Cylinder Replaced Now 2002 4WD Will Not Start
My son has a 2002 Explorer 4WD EB that needed new valve and intake manifold gaskets. I pulled it apart this weekend (battery disconnected) and replaced (don't get me started on the passenger valve cover with that *@&$^ EGR valve in the way). He's also had issues with the key being removable from the ignition when the vehicle is still running (worn key and/or cylinder most likely). So when I put his key in to test my gasket job, it won't go in all the way. After much trial and effort, I call a mobile locksmith who has to drill out the old cylinder and rekey/replace it (keyed to use the same, single old key we have).
Now, the cylinder turns happily with the old key. In the "Run" position, all the dash lights come on as they should, but turning then to "Start", caused a loud single click, then the dash goes out, and the engine never even tries to start. Then, nothing electrical in the car works unless I disconnect the battery for about 10 mins, then reconnect. Upon trying to start, the same thing happens (good dash lights at "Run", then single loud click from the engine compartment, then nothing. It seems maybe the PAT has lost its memory of the old key?
I watched and assisted the locksmith put the cylinder and PATS antenna back together, so I know connections/placement of that is good. At this point, I'm about to lose all the money I saved on the gasket job to the freakin' ignition issue.
Yaris/Scion & Vitz :: 2001 Toyota Echo - Ignition Lock Cylinder Replacement
The previous owner broke the key off in the ignition so I replace the ignition lock cylinder the problem is though even with the old one I can't turn the key to lock so it's stuck on acc. What I can try without replacing the entire column? Also it needs a catalytic converter, do I have to weld a universal one on ?
View 1 RepliesFord - Ranger :: 1994 - New Ignition Key Lock Cylinder / Steering Wheel Not In Locked Position
I easily removed the key lock cylinder but when I went to put the new one in I cannot get it to turn all the way back to lock the pin in place. The steering wheel is not in the locked position nor can I get it to lock. I have turned the steering wheel as far left and right as I could go with no success on getting it to lock or on getting the ignition key lock cylinder to turn back securing the actuator pin. The old key lock cylinder won't go back in either. What am I doing wrong?
View 3 RepliesTaurus :: 1999 Ford - Key Won't Come Out - New Ignition Cylinder
I put a new ignition cylinder the key won't come out at all. I was told that the key needs to come out in order for them to code the key. How do I get the key out of the ignition??
View 12 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Tailgate Lock Cylinder
I just bought a 'new to me' 2005 F250, Crew Cab with a v10. The Carfax showed up clean but after doing some detailing on it, I realized it had been resprayed and there was a little wrinkle in the bumper. I tried using the ignition key to lock the tailgate but it didn't work, so I'm assuming its been replaced. Need to confirm that the ignition key should be the key that works the tailgate lock or is the tailgate a different key that they guy never gave me?
View 8 RepliesFord Super Duty (1999-2016) :: Key Won't Move To Off Position After Cylinder Lock Removal And Installation
I have a problem with an 2000 F250 7.3 6spd. Recently, the "key in the ignition" chime kept dinging even when no key was in the ignition. I read in the forums that a wire can be disconnected to stop the chime. The problem is that after I re-install the cylinder lock, I cannot move the key to the off position to remove the key. I can rotate it to start and run, but it won't move backwards to the off or acc position.
The truck has this little lever that normally needs to be pushed to allow key to be released, but even after pushing that, turning the steering wheel back and forth, and messing with the tilt, I still can't get the key into the off position. I have removed the cylinder and it looks good. It rotates properly and I can remove the key, but only when it isn't installed. I tried replacing the ignition switch, but the lock cylinder still doesn't move.
I have an 04 F250 that I've tried swapping the lock cylinders from the 04 to the 00, but it still doesn't turn. What might be the cause/fix? Also, the 2000 F250 has a intermittent chirping/squeaking sound under the dash that happens even when the batteries are disconnected - might this be a malfunctioning vacuum motor? It happens even though the truck hasn't been driven for a week.
Ford Super Duty (1999-2016) :: 2004 - Tailgate Won't Open If Lock Cylinder Is Missing?
I just had the bed and tailgate on my 2004 replaced with a 2015. The body shop took my old lock cylinder out to put in the new tailgate. The old tailgate is only a year old and I wanted to sell it. The issue is that the latch will not open the tailgate. I can manually unlatch it by pulling the rods. Does the lock cylinder not being installed somehow affect this and need to be installed for it to function properly or do the rods simply need to be adjusted?
View 4 RepliesFord - Explorer :: 1999 - P0303 / Cylinder 3 Misfire - Resetting Code
On my wife's '99 Explorer, she just acquired, we had a P0303, #3 cylinder misfire. I found the plug cracked and replaced it. Do the codes reset themselves or do I have to do it? I'd rather not disconnect the battery and reprogram the radio.
View 7 RepliesFord - Explorer :: 1999 - Driver Side Electronic Door Lock Does Not Work
Replaced the door lock switch and all the other door lock switches in the car work, as does the one on the keyfob. How to figure out what's going on?
View 2 Replies