Elantra XD (2001-06) :: 2002 - CEL Flashing On And Off / Cylinder 3 Misfire
I have a 2002 Elantra with 123k on it. It has been having issues with poor acceleration, rough idle, surging, and the car just overall shakes sometimes when driving. The check engine light started flashing on and off periodically today, so I coded and it and it gave me P0303, which is a cylinder 3 misfire. I checked the spark plugs, and the cylinder 3 spark plug was pretty bad, so I went ahead and replaced all 4. The wires were in mint condition, so no issues there. I also put fuel injector cleaner in just for good measure. When I went to test the car, startup and acceleration/reverse were better, but the other symptoms still persist. What I should check next???
View 14 RepliesElantra XD (2001-06) :: 2003 GT - Cylinder 1 Misfire / Sputters In Acceleration
My car is misfiring, as in acceleration 90% sputters until I lay the pedal to the ground, which obviously isn't good for my gas. What do I do? I can't find anything online and I don't want to be throwing money into things that don't work.
View 4 RepliesElantra XD (2001-06) :: Random Misfire On Cylinder 2 / 3 And EVAP Codes
Trying to troubleshoot my 2001 Elantra (173k). I'm having intermittent trouble codes being set and I'm wondering if they may be related:
P0302
P0303
P0446
The cylinder 2 and 3 misfires are relatively recent. Plugs and wires are visually ok (and not that old). I swapped plugs 1 and 4 with 2 and 3 to see if the plugs are bad. It took 3-4 days, but the P0303 set again (and it's very intermittent - car will noticeably lose power for a few seconds, code set, then run fine for several days). I also sprayed carb cleaner on the intake manifold gasket with no change in engine idle, so the gasket appears to be intact.
I had read in a forum somewhere that the misfires could be related to a vacuum leak, which could also be setting the P0446 code. I removed the charcoal canister and inspected the lines - visually ok.
I bench-tested the canister control valve and it did operate, though I noticed some charcoal blocking the valve so it would not close all the way when energized. I used compressed air to blow the debris out of the valve and it appears to close properly now.
I went to hmaservice.com and noticed there are no instructions for the P0446 DTC. I've been using a Haynes manual instead. For quite some time now when refueling, the fuel nozzle shuts off every few seconds (I have to slowly put the fuel in to avoid).
Some questions:
- Can these codes be related?
- Based on my symptoms, should I replace the canister control valve? What about the charcoal canister and the charcoal air filter - should those be replaced as well?
- What else should I check?
Elantra XD (2001-06) :: Cylinder 2 Misfire / Rough Idle Especially After Fill Ups
I have a 2001 Elantra with 170K miles. well taken care of. I've been having a rough idle issue for some time now. The car idles very rough. I checked for codes and I got the cylinder 2 misfire code (P0302)...
I started out and replaced the plugs and wires, no solution...
I replaced the coil packs, no solution...
I replaced the MAP sensor, no solution...
I figured it may be no to low compression, so I did a compression test and all cylinders came back normal, still no solution...
I figured it might be a dirty injector, so I poured some seafoam in the gas tank, and no solution...
So my next step is to switch out the injector. Is there anything I am overlooking?
Here's the big thing that is happening too... Everytime I fill up the gas tank, I turn the car on and it idles even rougher. Like if you talk while sitting in the car, you sound like Chevy Chase when he is on the vibrating bed with Beverly D'Angelo in the movie vacation! LOL. It slowly goes away after 10-15 minutes of driving. All this rough running engine ONLY happens at idle, otherwise it runs very smoothly.
Elantra XD (2001-06) :: Check Engine Light (cylinder 3 Misfire)
As the title says I have plugged a code reader in and it says "cyclinder three misfire". So I pulled the plugs and good god they were nasty. Some having a gap of 80-90 thousandths of an inch. So I figured the plugs were the source of the problem, thus I replaced them but to my dimise the check engine light is still on, and still reading the same ol' "cyclinder three misfire". I have put 350 miles on it in 24 hours of changing it to allow for proper time of the circuit cycling for the light to change but not sure if it takes longer...?
I also went ahead and checked the plug wires resistance when I had the plugs pulled and they ranged from 1.5-2.5k ohms shortest to longest (cylinder 4-1). And if your curious the magic cylinder three was around 2k ohms for however long that wire is, my guess would be 18 inches. Would this be out of tolerance, I know the norm is 10k ohm for every 12 inches or so...?
My next guess would be replacing the power pack or I guess you car guys call it the "ignition coil"...? I will say that the car does run much smoother after replacing the plugs.
Elantra XD (2001-06) :: 2003 - Code P0303 Misfire Detected On Cylinder 3
2003 hyundai accentra and I have trouble code P0303 misfire detected cylinder 3 the car would run rough and hesitate at idle and run rough in drive and reverse I checked the plug gap on number 3 cylinder and it was excessive so I regapped it and put back and the car run good for about a day and now the engine light is back and is running rough and hesitating.
View 1 RepliesAccent LC (2000-05) :: Cylinder 3 Misfire / Massive Hesitation Under Heavy Throttle
I've got a 2000 accent 1.5, and I keep getting a code for a cylinder 3 misfire, when I change the spark plugs, it runs great for about 50 miles or so, then back to square one again. I just changed the coil pack the other day and there doesn't seem to be much of a difference. It has massive hesitation under heavy throttle, and the check engine light begins to blink if it sits and idles for too long. I've scanned it multiple times and it's always been cylinder 3, so it's definitely set on that one... I'm about stumped on what this could be. Also, the previous owner said that after a hot day of driving, the ECU fuse under the hood will blow out, what could cause either one of these things?
View 40 RepliesGolf IV / Jetta IV :: Loss Of Power And Hesitation / CEL Code For Misfire On Cylinder 1 And 5
When i got my 2000 jetta vr6 it has a CEL for misfires. Searched this board and google already. Im thinking injectors (havent checked yet) I noticed something weird the other day. At a light i get the CEL flashing. Then after a bit it will come on and stay on. I plugged in my generic reader and deleted the codes. When the CEL is on I get loss of power and hesitation. When its deleted the car runs better. I get my power back. I looked in the coolant tank and see no bubbles. Could this be the ECM? Im still going to get injectors but want to buy the gasket and anything else I am going to need to put it back together. I already cleaned the MAF, replaced some vac lines, coil pack, wires and checked plugs (gapped at .28) ...
View 4 RepliesFord F-150 - 1997-2003 :: CEL Code Signifying A Cylinder 3 Misfire - Shudder / Hesitation
I will add as many details as possible :
2000 f150 4x4 offroad package
5.4L with 131k on it
new Dorman intake manifold
new Global Automotive (Ebay) COPs
New Motorcraft spark plugs
About 1500 miles ago I started throwing a code signifying a cylinder 3 misfire. The truck would bog down real bad and then after 5-6 seconds of no power it would return to normal. I tried replacing the COP (both with new and then with one from another cylinder) and plugs but no resolution. So I talked to the local ford service manager and he said it sounded like intake manifold problems.
Replaced the intake manifold and no more codes were being thrown.
1500 miles later and today the truck started having a hesitation/shudder when I was sitting in a drive-thru. I put the truck in neutral and park and neither solved the issue. With the earlier issue, when I would put in neutral and increased rpm, the issue would resolve.
I pulled out of the drive-thru and the hesitation was consistent no matter what the rpm or speed. The truck feels almost sluggish and lacks power. The hesitation is like 2x/second. When accelerating its almost like the rpms and speed hesitate, jump, hesitate, jump.
Hyundai - Elantra :: 2002 - Rough Idle And Misfire When Hot / Intermittent Hesitation When Accelerating
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
Elantra HD (2006-10) :: 2008 - Misfire On Cylinder 2
My 2008 hyundai elantra misfire cylinder 2 i have changed coil , wires and spark plug and still have misfires.
View 5 RepliesPassat (B5) :: 2001 V6 - Engine Hesitation / Misfire On Acceleration
I have an 01, early model, AWD Passat wagon, v6, GLX and when I accelerate from a standstill or a slower speed, the car hesitates slightly and coughs(?) and then catches on and accelerate. It doesn't actually backfire or misfire.
View 2 RepliesPassat (B5) :: 2001 - Misfire On Cylinder 1 And 2
I have my timing belt and oil pump replaced and after 2 days the car was misfiring. Had the throttle body clean and reprogramed and still the same issue. run all test and its ok. What the issue will be. I was told it can be the ICM but the mechanic says there is no way to test it.
View 2 RepliesDodge - Ram :: 2001 - Misfire On Cylinder 1
I have a misfire on 1 I recently changed intake and plenum gasket, changed plug, wire, injector, cap, rotor, compression check and pulled valve cover rockers moving good and I recently swapped injector wires on 1&3 only shows misfire on 1.
View 5 RepliesSanta FE SM (2001-06) :: Misfire In Cylinder 3 And 6
I am trying to fix my friend's 03 Santa Fe 2.7L with 325K miles on it. Pulled the codes and he has misfire in #3, 6 and a random one. It doesn't do it all the time, and when it does do it he can sometimes shut it off and restart it and it will be fine.
What is the likely culprit causing the misfires and how to test it? He can't just throw parts at it.
Passat (B5) :: 2001 - CEL Came On / Misfire On Cylinder 2?
my dad has a 2001 Passat and he recently had his check engine light come on. We had it checked by a guy who owns a tester (snap on) and it comes up with a misfire fault on cyl #2. Wire looks good, I didn't have tools with me so I couldn't take a plug out, but do you think it could be a bad spark plug? Bad coil? Car has 89K on it.
View 5 RepliesElantra XD (2001-06) :: Hesitation Throughout At 0 - 15 Mph
My 2001 hyundai elantra hesitates throughout 0-15 mph I have changed out TPS,MAP,& IAC and i have did a full tune up and a transmission flush & I still have the same problem.
The one thing i did notice is the engine doesn't rev up when ac is on. Idle stays the same with A/C on or off.. when I go to plug the IAC in, with the car running it opens the valve but once i fully connect the plug it closes ... does the same thing with new and old IAC..... and the connector on plug is good..
Ford - Windstar :: 2001 - Misfire On Cylinder 1 And 3
I have a 2001 ford windstar the codes are bank 1 lean (wires have been cut) could this cause the miss fire on the #1 and 3 cylinders? The previous owner put copper plugs in it instead of platinum. How hard is it to change the plugs?
View 6 RepliesGolf IV / Jetta IV :: 2001 - Misfire On Cylinder 4
New to the VW world but I am not out of my element for I am a Porsche guy. So I feel right at home. Last night I picked up a 2001 wolfy Jetta with a 1.8t on the cheap with a misfire on cylinder 4.
I have verified I have no spark on 4. I have confirmed the issue is not the spark plug, coil pack by swap and see method. My coil pack and plug work fine on another cylinder. I reset my cels and here are the new ones that pop up:
a 121 - gas pedal position sensor- doubt this would give me a no spark
a 304- Misfire on 4, (duh, like I needed to hear that)
a 030- bank one 02 -Doubt this would also give me a no spark condition)
In my testing:
I have good system voltage on the coil pack
I have good ground ohms
My signal wire is not shorted high or low
When I take V and ohm readings on the coil pack connection, either with the ign on or off they are all in line with the other sensors. So I don't think I have a wire issue.
The PO had the ECU replaced at a local dealer. I looked at the old ECU and it appears it had got wet at one point.
Im wondering if the same thing hasn't happened to the new one. however after they replaced the ECU they gave him the car back still broken. So it never ran even with the new ECU.
1 Where is the ECU?
2 What tells the ECU to fire the coil packs at the right time?