Sebring - Chrysler :: 2005 - Jerking Forward At 2750 RPMs
My 2005 2.7L 6 cylinder Sebring with 100800 miles that was running fine just started jerking on me last week. It runs fine untill I get it up to 2750RPMs. Its like its getting gas, then not getting gas and jerks forward all in less than a second and then again, and again and again, until I drop the RPMs back down. Any clue on what I should be looking for?
View 4 RepliesHonda - Accord :: 2005 - Engine Lurches / Stutters And Oscillates At 2500 RPMs
Yesterday as I crawled my way through heavy traffic on my drive home from work, my car started lurching unexpectedly. When I let up on the gas, the lurching subsided. I was able to recreate the behavior multiple times on my drive home, as well as while parked in my driveway. As the RPM exceeded 2500 the engine would lose oomph/power and the RPM would start stuttering/oscillating between ~2500 and ~2800 RPM. The behavior was identical regardless of which gear I was in (D1, D2, D3, D, or N), regardless of my speed, and regardless of how aggressively I was pressing the accelerator pedal. Every time the RPM hit 2500, the engine freaked out.
This morning, it did NOT happen when I tested it briefly. I was able to rev up to 3500-4000 RPM without any issues. I did read a case online in which someone experienced a similar issue that only manifested after the engine had been running a while. My car has ~173k miles on it, and this is its first engine issue. What might be causing this?
Video attached; also located here: [URL] ....
Sebring - Chrysler :: 2005 - In Hot / Humid AC Blow Hot Air?
I have the above mentioned 2005 Sebring Convertible (2.7L V6, Touring) and the AC will work occasionally, but when it is hot and humid, it is sure to blow hot. First up was to check the system pressure and top off if needed - not the problem. Also blew the bugs and junk from the radiator fins. The wires and electrical connections look good at a glance. Turning the car off and on again doesn't work. Why would the darn thing work part time and take days off when we need it most?
View 1 RepliesSebring - Chrysler :: 2005 - How To Get Brake Caliper Off
I've run into a problem while doing brakes on my friends 2005 Sebring. I can't seem to get the brake caliper off. There is a little rubber boot with a plastic cap that is where the bolts that hold the calipers in place are. How to get the bolts out to remove the caliper. In fact, it doesn't seem like there are any traditional bolt heads in the plastic cover.
View 2 RepliesSebring - Chrysler :: 2005 Sedan Jerking / Bucking While Going 20 - 25mph
I just bought a 2005 Chrysler Sebring sedan 2 weeks ago, has 94,000miles on it. Had no problems with anything until 6 days after purchasing the car. I just got on the highway & was about a mile onto the highway & I was already up to speed 65mph & my whole car just starts jerking (bucking like a horse) & I let off the gas & it'd stop. I'd give it gas again & it would start to jerk(buck) again; I had to get to work so I drove it for the couple miles I had left to get to work.
As I got onto the off ramp I noticed my car didn't jerk/buck like it was at the higher speed. After work I drove back home & on the highway without any problems. I also didn't have any warning lights come on while it was jerking/bucking. (Before this incident, I had drove to my moms, which is 1hr & 45min away, & back with no problems). I took it to a local mechanic & they found nothing wrong, & they test drove it & checked all the fluids/filters/spark plugs. I did need new front break pads & rotors so I had them change those.
Four days later my car did it again.. the jerking/bucking. But this time it was at a low speed & I noticed a ding(like the kind of ding your car makes if you don't have your seat belt on), but again I saw no warning lights come on. I kept driving & was almost to get onto the highway & was about 20mph & my car started to jerk/buck again. I thought it might be nothing so I kept driving to get onto the highway. I turned onto the highway onramp & started going 20-25mph & my car started to jerk/buck like a horse & not let me accelerate any faster.
So I pulled onto the onramp shoulder & turned my car off then back on again & let it sit for about 5 minutes & got on the highway & it was like my car had magically been fixed. I got up to speed (65mph) just fine with no jerking/bucking. Again this time none of my warning lights came on & I didn't have any smoke coming out the back end. I of course immediately went strait home, but had not signs of the jerking/bucking. My car also when I start it, all of my dash warning lights come on like they normally would whenever you start up your car, so I know they all work.
Sebring - Chrysler :: 2005 - Air Injection Pump Draining Battery
A couple of weeks ago, with the car turned off, keys out of the ignition - about every thirteen seconds you could hear the air injection pump coming on, running for a couple of seconds and then turning off. The next day the car battery was dead (no surprise) so we charged it up and took it to the shop (AAA) . They told us that it was a faulty MAP sensor and didn't give us a price quote to fix it, just an invoice/diagnostic bill. But they did unplug the air injection pump so that the battery wouldn't keep getting drained.
We drove the car home and called them the next day to get an estimate for the repair and they said that they misdiagnosed the problem and that it was actually a MAF sensor that was causing the air injection pump to come on when the car was turned off and that it would cost around 500 dollars for the part and labor. Too steep so we decided to hold off on the repair. Understanding our reluctance to go through with the repair, they recommended that we plug the air injection pump back in and still drive the car but to make sure that we unhook the battery at night/when the car would be sitting for many hours without being started.
Here's where it gets a little confusing (or at least for me). I did take AAA's advice and went ahead and plugged the air injection pump back in and for the last couple of weeks it's been fine. No issues with the battery being drained whatsoever/no air injection pump coming on with the car turned off. But today the air injection pump started doing its thing again.The check engine light was on so I hooked my code reader up and pulled the following codes:
PO128 (thermostat coolant temp below regulating temp)
PO491 (secondary air injection system (Bank 1)
PO2431 (secondary air intake system FLW/Perf B1
Does all this point to a faulty MAF sensor?
Sebring - Chrysler :: 2005 - Normal Range For The Temp Gauge?
At idle temperature is above middle. Upper radiator hose, which is connected to the thermostat is hot. Lower radiator hose that feeds back to the engine is cold. Radiator fan will not stop running if the temp guage is at middle to needle above middle. When running the temperature reading is normal at 30 mi/hr (middle to just below middle). Temperature will also go down if at high rpm idle, about 2,500 RPM.
New thermostat replaced last week. Water pump replaced less than one year ago. Upper radiator and lower radiator hoses are pressurized when running and off.
I suspect the thermostat was installed incorrectly. Pressurized hoses mean excess air in the cooling circuit/system. If so, does it mean I have to bleed out the air? How do you bleed out the air on a cooling circuit of a car, I thought the reservoir tank already does that naturally? I think the normal range for the temp guage should be 1/3 of the whole range of the guage, right?
Sebring - Chrysler - Engines :: 2005 - Repeatedly Chugs / Recover While Driving
Check engine light comes on, car starts "chugging", recovers, chugs, recovers. So we limp to our destination. Check engine light goes off after car stands overnight. Repeat after driving car again. Mechanic replaced a 4" square "switch" somewhere "hot" last time. Said heat makes it go bad. Can't find anything 4" square under the hood. Mechanic says this part goes out all the time on this model and year.
View 6 RepliesSebring - Chrysler - Timing-belts - Vibration :: 2005 - Whining Noise At Idle
I have a 2005 Chrysler Sebring. In December the timing belt failed while I was driving down the road. I had the dealership I purchased the car from replace the timing belt as well as the water pump while they were at it. Ever since I have had and issue with it vibrating at idle. At first it was making a whining noise as well. I took it back and they told me that they had installed the belt too tight. Afterwards I still had an idle issue although the vibration was a little different. I also could distinctly hear the belt hitting the casing a few times.
I took it back again and they stated that the belt had been put on too loose. So now they have adjusted the belt again and it I am no longer having the whining or belt hitting the casing. But I still have an idle issue. It has changed again and is kind of a pulsing vibration. I can feel it in the brake pedal when I am at stops. I seem to hear the pulsing while driving as well but this may be from my new tires as well.
During this whole readjustment process they have not mentioned actually checking the timing. Just the belt tension itself. When I first reported the idle issue after they put the timing belt and water pump on they told me that it could not be related to timing and that it had to be an ignition issue. But I asked a work associate who used to work as a mechanic and he stated that it would be a timing issue.
I am going to contact the dealership and ask them to check the timing belt again. I never had this idle issue before the new timing belt.
Sebring - Chrysler :: 2005 - Wiper Motor Not Working / Gauges Started Flashing On And Off
It's a 2005 Chrysler Sebring with a 2.4 DOHC. A couple weeks ago I tried to use the wipers and nothing happened - at all. The next day the gauges inside the car went hay wire, started flashing on and off. Turned out the car needed a new battery and alternator. Replaced both and the car has been perfectly fine - except for the wipers. I checked the wiper fuse and it wasn't blown so I pulled the cowl, unplugged the motor, turned the key on, turned the wiper switch to full speed and then tested for voltage at the plug and got almost 12 volts when testing several terminal combinations.
I thought for sure I had it figured out so went ahead and bought a remanufactured wiper motor but nothing happened when I plugged it in. I thought maybe since I didn't mount it it wasn't grounded so went ahead and did that and still nothing. Thinking maybe it was defective I returned it and went to a different auto parts store and bought another one, hooked it up and got the same results. So then I tested all nine relays in the relay control center and they all passed. So now I'm thinking the only thing left to test is the wiper switch. Am I correct?
And also I'd love to bench test the original motor just to verify that it works but don't know which terminals to connect to. I've searched the internet with two different browsers and came up with nothing. The motor in question is a Bosch 05-02-14 41. And then underneath it has 0390 241 7411 12V 058 written on it. The terminals are labeled: 31b, 31, 53 and 53b. And since the OE replacement motor for this car is a Cardone 40-3026, which terminals to use to bench test that one, I could then figure out which terminals to use on the Bosch.
Chrysler - Sebring :: 2002 - Engine Is Blown?
I have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 RepliesKia - Rio :: 2005 - RPMs Won't Go Past 2500
I drive a 2005 Kia Rio with 48,000 miles. Every once in awhile (particularly after a bit of driving when everything is warmed up) the RPM won't go past 2,500. I'll put it in 1st gear, accelerate till 2,500, but as soon as it gets there, the engine gets groggy, the car slows down, and I have to quickly switch to 2nd and repeat the cycle on every gear. Flooring it makes it worse.
Obviously the fastest I can possibly go with this happening is about 50mph on 5th (just below 2,500). This has happened three times and it has fixed itself every time so far.
A possible clue may be that the check engine light frequently comes on, and its always the same culprit: this "flow meter" sensor. I've had it replaced three times now, but it still always trips the engine light. I now just ignore the check engine light.
C/K :: 1999 Chevy 5.7 MT 2500 - Engine Cuts Out While Driving At 3000 RPM
MT 2500 Where are you I've got a weird one. 99 Chevy 5.7 dully dump truck. The engine cuts out while driving at 3000rpms only. If you keep your foot in it it goes away at 3200. Does it in any gear(auto). Also, stopped and in park, it will do it at 4000rpms. Acts like a rev limiter. Fuel pressure does not change (60-62psi) when this happens, does it in open or closed loop. I disconnected the maf and no change. I've installed new cap, rotor, plugs, wires, coil, module(all original with 165K), no change. Runs sensational until 3K rpms.
View 14 RepliesSebring - Chrysler :: 2004 - Engine Wants To Stall When Idling
I have 2004 chrysler sebring and lately when I'm at a light/stop sign the rpm gauge fluctuates between 1000 and 500 and wants to stall. I've been told to change the spark plugs and wires, cleaned the throttle body, and put in a new air filter. What else I should do?
View 1 RepliesChrysler - Sebring :: 2006 2.4L - Engine Keeps Rattling And Making Noise
Engine oil has been changed and spark plugs changed. The engine is still making rattling/clicking noise. I checked with a mechanic and he indicated that engine needs to be repaired. Didn't say exactly what needs to be done and stated it would cost about $2200 for parts and labor. Why the engine keeps rattling and making the noise? Oh, before plugs were changed, the engine was shutting off at times when in idle mode.
View 5 RepliesSebring - Chrysler :: 2001 - Engine Starts Then Immediately Shuts Off?
A couple of months ago my daughter's Sebring engine began shutting off immediately after starting. We brought the car to my usually reliable mechanic. They couldn't find anything wrong. The problem became more frequent (every 2 to 3 starts) and we brought it back to my mechanic who determined it was the car's computer system. $1700 later the car is ready to be picked up, my daughter gets it after the shop is closed, and it wouldn't start! She left it there, got a ride, and, one week later the Sebring is still at the mechanic's. They told us it starts every time for them and they don't see any problem. After researching on the Internet I thought it might have something to do with the immobilizer but they told me that tested fine. I'm at a loss over what to do.
View 2 RepliesSebring - Chrysler :: Check Engine Light Is On / RPM Too High While Driving
I have a 2004 Sebring my check engine light is on and the RMP's are really high while Im driving. What could be going on?
View 11 RepliesChrysler Sebring :: 2006 - Whine From Engine And Intermittent Battery Light
About a week or two ago, when driving home, my battery light flicked on while at a stop light. Also, as the light wen t green and I accelerated away, I noticed a kind of 'whine' from the engine, like a turbine spinning up. By the time I got home it was fine again and the light out, and has been until today, when it happened again...I noticed that it happens if I have the AC on and I'm at a stop. If I turn off the AC when waiting at traffic lights, that seems to eliminate the battery light, but I still here the whine.
View 4 RepliesSebring - Chrysler :: 2001 Mitsu 3.0L Engine - AC Alternator Belt Hanging Under Car
Earlier today i noticed a loop hanging under my car. When i removed the item it turned out to be my AC/Alternator belt. Thinking it was bad i went ahead and got a new one. Prepared for a hard battle i find that the part slips on easily. now i can not get the belt tight at all it had about an inch or 2 of slack. I do not have a repair manual and i do not have the money for one. I can not find a diagram for my specific engine. It is a 2001 Chrysler Sebring with a Mitsubishi 3.0L 24 Valve Engine. What am I doing wrong? I need this fixed to go to work tomorrow.
View 16 Replies