Chevrolet - Suburban :: 1999 - Running Sluggish When Accelerate Car Will Not Go
I have a 1999 Chevy Suburban K1500 4 wheel drive. It has a 5.7 liter engine and has 360,000 miles. I recently had a fuel pump put in last year. It is now running sluggish when I accelerate it will not go. This happens after it seems to warm up about 15 minutes of driving. I just replaced the fuel filter thinking that it may have been plugged up but it is still running poorly. When I put the fuel pressure gauge on it, it read 61-62 during start up and then dropped down to 57-59 (pulsates rapidly) after I started it.
View 2 RepliesChevrolet - Suburban :: 1999 Vortex Running Sluggish When Accelerate
Well I just set the timing on my rebuilt chevy 5.7 1999 suburban. It still runs sluggish when I accelerate and idles nice when it'd parked. I rebuilt the whole part part of engine. This is what I did notice when I cleaned under the lower intake manifold where the fuel injectors plug in. Here is a attached picture.
View 1 RepliesToyota - Rav4 :: 1999 Engine Flutter / Occasionally Won't Accelerate From Full Stop Or Low Speed
Our 1999 automatic Rav 4 (157,000 mi) occasionally won't accelerate from a full stop or from a low, in-town speed. You step on the accelerator and the engine just flutters at low rpm, stuttering. If you drop it into neutral and start revving it will eventually "catch" and be fine. Very dangerous when entering roadways. We have a new timing belt, cleaned up throttle plate, new sparks, water pump, oxygen sensor.
View 1 RepliesChevrolet - Suburban :: 2002 - Engine Stalls At 75 Mph
2002, Chevy, Suburban 1500, 4wd, 5.3L engine, 210,000 miles. Mass airflow sensor and both O2 sensors replaced last year in an effort to fix this problem. Original problem surfaced when the vehicle was shut down or running uphill and had about 1/2 tank of gas in hot weather. If stopped, the vehicle would not start until it had cooled down. Sometimes getting it onto level ground would be enough to get it running again. ( This accomplished by turning on the key and allowing the vehicle to roll back out of the parking place. ) If running down the road, getting to level ground after the stall, pulling to the shoulder and cooling the engine/waiting a few minutes and restarting the vehicle would work. This was before the above mentioned repairs.
Last weekend in 60 degree weather I was driving back from northern Michigan and as I headed up hill at 75 mph with the tank at 1/2 the vehicle did a high speed stall on me. Symptoms were: RPM showed 2000, but pushing down on the gas actually dropped the RPM no matter how feather-footed I was. This was tried several times. I turned on the 4 ways and moved toward the shoulder and at 50 mph finally got the thing to restart. The rest of the trip home was uneventful.
I had a 2001 Suburban with the same specs which did this same thing until a factory recall that got me a new fuel pump. I asked about the recall the last time my truck was in for service and they said it does not fall within the serial numbers for that recall. Fuel filter replaced about 9 months ago. Co-incidentally but not necessarily related is that my battery with less than 3 years of a 7 year warranty was draining itself in less than 2 days this last winter.
Chevrolet - Suburban :: Engine Revs When Vehicle Stopped
My engine revs up no matter if the thing is hot or cold when I come to a stop at a red light, SOMETIMES. Other times it will idle at 100 and then wants to idle around 1000 and has idled as high as 1200. I've been told EGR, TPS, Idle Control Motor, or Intake gaskets. I did have a code 22 which occurred after a friend unplugged the TPS and reconnected it, but no other codes or check engine lights. Tuned engine 2 weeks ago, but problem still persists. Where do I start and what equipment do I need. I am a professional diesel tech, but not so much with gas.
View 3 RepliesChevrolet - Suburban :: 1996 - Dry Start Only When Engine Warm
My Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
Chevrolet - Suburban :: 1997 - Diesel Engine Dies - Dashboard Lights Don't Come On
My '97 Chevy Suburban diesel dies at random times. Nothing seems to trigger it; it usually happens when I'm just driving along, minding my own business; not accelerating or decelerating, turning, stopping, etc. Has happened with the fuel tank at every level: full, half full and quarter tank. When it dies, the dashboard lights do NOT come on. When I turn the key "off" and back "on", the lights come on and the engine will crank fine, but won't start. Ten minutes later, it starts and everything is fine. It may not do it again for weeks, or it may do it again in 10 minutes.
This last time, the fuel tank was fairly low -- below a quarter tank -- and it seems to "buck" or "hesitate a little just before it died the first time. The dealer replaced the crankshaft position sensor and the fuel injector pump. When it started doing it again, they ran every diagnostic test they had and could find nothing wrong. Ran fine for a few weeks, then quit three times in 30 minutes. It's back there now.
Chevrolet - Suburban :: 1998 - Engine Hard To Start When Cold Outside Or After Rain
I have issues with engine starting when cold outside or after rain. This only happens when engine is cold and has not been started for a day or 2. Distributor cap does not have any condensation inside but does seem to corrode on contact points. Engine turns over fine, has fuel and spark. When this happens engine will not fire and after awhile it will start to fire and lock up when it fires then continue cranking. After repeated attempts it will start and run fine, can be shut off and start right back up with out any issues. It could take a few tries to a few hours of trying before running though. I'm leaning toward a distributor or timing issue. Am I on the right track? 98 Suburban K1500 5.7L ....
View 6 RepliesChevrolet - Suburban :: 2007 - Misfire After Working On Engine / SES Light Flashing While Driving
I replaced the oil pressure switch on an '07 Suburban 5.3L because the oil pressure was showing low once the engine warmed up. That did nothing, then I found out about that little filter/screen under the sensor. I intended to remove and clean the filter then reinstall it. While I was pulling it out, I dropped it back behind the engine and couldn't find it. I checked online and found a few people in other forums that said to just remove the screen as a "fix", so I left it out and put the sensor back in, just to get the vehicle drivable. It started right up and ran fine for me, parked it, and a after sitting for a few hours it started popping while driving with the SES light flashing on the drive home.
Code P0300 was set, no cylinder specific misfire codes were present. I checked the misfire data and cylinder #6 showed tens of thousands of misfires, #5 showed several hundred, but I think it was just picking them up from #6 since #5 is right after #6 in the firing order. I disabled each injector with a scan tool, all changed the idle except #6, it did absolutely nothing. #6 fuel injector had good pulse to it, I connected a fuel pressure gauge and put power/ground to injectors #6 and #4, both dropped the same fuel pressure. I did the "cylinder deactivation" test on the scan tool for the four cylinders that have it, they all did the exact same thing - the engine bogged way down for a couple seconds and then died. Is that normal? I can't say I've ever seen a V8 engine die before when running on 6 or 7 cylinders. I checked compression on cylinder #6, it showed very low, almost zero, but I tried it a few times and it would show just a little compression at times... valves staying shut? I'm thinking when I opened the pressure relief valve on the gauge and the piston was near the bottom of the cylinder may be when it showed some compression. I also switched the coil/wire/plug from #6 to other cylinders and the miss did not follow.
Could having that screen out cause this problem? Having the engine die when deactivating the cylinders makes me wonder if maybe it's commanding all four at the same time, although the test shows each cylinder being controlled separately. Using a MODIS, not a TechII. I just got done putting in a new filter/screen to see if it would make any difference, and of course it didn't.
Chevrolet - Suburban :: 2001 - Engine Severely Lacking In Torque For The First Minute Or So Of Driving
I have here a 2001 3/4 ton Suburban. It arrived last fall with 280K miles and a 6.0L V8 that was on its last leg (low to no oil pressure). I dropped in a 5.3L that I had handy, and had been happily driving it throughout the brutal Minnesota winter.
A couple months ago I noticed an issue developing. After a cold start, the engine would be severely lacking in torque for the first minute or so of driving. You could reach any RPM you wished, but the truck could barely accelerate. Once a minute or so had passed in this fashion, the issue would suddenly disappear... you'd be thrown back in your seat a bit if still attempting to accelerate, and the truck would take off. For the remainder of the trip, things would be fine.
Recently I went to drive the truck after it had sat for some weeks. It started fine, but the issue was now more persistent. When trying to accelerate, the gutlessness would continue for a good 15-20 seconds until finally and suddenly disappearing. Let off the gas, wait a moment, try to accelerate again, and it was the same thing all over again. Eventually I also noticed very obvious stumbling/missing when trying to get moving from a dead stop. Idle remained smooth.
The plugs and wires are only a few months old. The fuel filter is new. I checked for vacuum leaks (none that I could find). Fuel pressure is consistently around 50psi, even while the issue is happening.
The MIL was not on. I checked with my scantool, and found that P0101C was set, with P0101 pending. Visually examined the MAF harness and sensor; all looked fine. Swapped in a used working MAF; no change. (I suspect these codes may be due to the fact that I'm running a 5.3 with a stock, unmodified 6.0 PCM.)
My scantool is a Genisys running System 2.0. I'm by no means an expert with it, but I did know enough to try watching the miss counts while the symptom occurred. All cylinders seemed to be missing equally as much as the others, more or less.
Normally I'd be suspecting the fuel pump and/or associated wiring was going bad, but the pressure seems fine. What I might be missing?
Chevrolet - Suburban :: Squeal / Groan / Clicking Noise Coming From Right Front Of Engine When Accelerating
2003 Chevy suburban, 115K miles, accelerating I hear a squeal/groan/clicking noise coming from right front of engine. Did not happen this winter, started again in spring. Loses power if stay on accelerator. If let off and then reapply, it will momentarily go away. Appears to be only when air conditioning on. Bad AC or just the pulley?
View 1 RepliesChevrolet - Suburban :: 2001 - Constant ABS / Flashing Service Ride Control And Change Engine Oil Warning
I checked the cables, no corrosion and tight as a drum. I connected an OBD II computer to the plug under the dashboard and the computer replied that there were no trouble codes present. Is OBDII the proper code reader? none of these lights were on before I replaced the battery. now I have constant ABS, flashing Service ride control, change engine oil. The battery has not gone dead as of yet but the ampmeter is charging at about 16.5-17 volts. I disconnected the pos terminal while the vehicle was running and it continued to run even with the lights on.
View 2 RepliesGTI 337/20th Anniversary :: Engine Started To Flutter Abnormally
So I'm new to the vw world and my 337's engine started to flutter abnormally. So I searched up and down google and vwvortex to troubleshoot the problem. turns out i needed to change my dv so I bought a new one, replaced it how the old one was set up and my engine began to shake and seemed as if it was knocking. Forge DV 007...
View 5 RepliesChevrolet - Suburban :: ABS Light Stays On
If sensor or control module malfunction. Brakes are fine. If ABS relay, so where is it located, cant find in fuse box. This is a 1500 2WD suburban.
View 5 RepliesChevrolet - Suburban :: 2003 Shakes When Drive Over 70 Mph
My 2003 Suburban shakes when I drive over 70 mph. I don't know if the tires need realignment?
View 4 RepliesChevrolet - Suburban :: Dropping Out Of OD For A Split Second And Then Going Back In
I have a 1990 suburban that has had a rebuilt x-mission about 50,000 miles ago. At this time when I drive there is a hesitation, split second, when running on flat road. It happens when going up a hill, too.My mechanic said change the: plug wires, then the plugs and rotor. No difference.
I think the thing is dropping out of OD for a split second and then going back in. If I drive in 3rd, I don't think it is happening. Isn't there a relay or solenoid that controls this function?
Chevrolet - Suburban :: 2005 - Won't Start When Cold?
I have an '05 Suburban with starting issues. When it's cold out (below 40 degrees) and you turn the key, all accessories come on but truck will not crank. It then seems like the power just cuts off.......dash lights go out but gauges are fixed in place and a couple of seconds later, I hear a strange buzzing noise from the dash area behind the radio and the gauges will then go to power off position. Then if I try to start it, there is nothing, no lights on dash, no starter engaging, no clicking of the relays, nothing. I tried, on a hunch to disconnect the ground lead from the battery. Had it off for 10 minutes or so, put the cable back on, tightened it down (wasn't loose to begin with) and it started right up first try in 20 degree weather. I had previously had the battery and alt checked and both were good.
View 3 RepliesChevrolet - Suburban :: 1995 - Stuck In 3rd Gear
1995 Chevy Suburban, currently at 150,000 miles, Prior owner had transmission rebuilt prior to 100,000 miles. While towing my 18ft camper trailer on a recent trip every time I started off from a stop I had to really push on the gas to get going. At first I though the emergency brake was on, or I had a flat tire. I then noticed the automatic transmission was not shifting when I had it in D. Checked the transmission fluid and it was full. The transmission seems to be stuck in 3rd gear. When I move the shifter to 2 it will shift down. Reverse is also still working. Am I in for a costly repair?
View 3 RepliesChevrolet - Suburban :: Random Power Drop Off?
I have random power drop off (best description is a loss then a surge or something like a skip) when driving over 60 mph. If I let off the gas or floor it the problem goes away temporarily. No mechanic has been able to figure it out. Chevy dealer just says "we don't have any codes".
View 10 Replies