Lexus ES 2007-12 :: Code P0368 - Camshaft Position Sensor Error
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 RepliesFord - Explorer :: 1996 - Check Engine Light Code P0340 - Camshaft Position Sensor
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 RepliesCamry :: Toyota 2002 LE 2.4L - Code P1379 Camshaft Position Sensor
The computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 RepliesSonata NF (2006-10) :: Camshaft Position Sensor Error - Check Engine Light On
06 sonata 3.3 L V6. Light has been on for a month or two...took it in to mechanic yesterday and it's a camshaft position sensor error...it makes total sense to me now because my cars been starting hard, seems like it gets hotter then usual...and had a "clicking" noise for about 10 mins, then gradually goes away. it takes a few extra cranks now to start the engine unless it was already fired up.
Also does a jerk once and a while around 40 km/h. I looked online and those seem to all be symptoms of a failed camshaft position sensor (CMP). Would those symptoms seem about right? Am I okay to drive slowly for the weekend before I get the new sensor installed? The mechanic didn't seem to worries about me driving for just the weekend...but it's worrying me a bit...
Accent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesElantra XD (2001-06) :: 2003 - CEL Code / Bad Camshaft Position Sensor
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
Accent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesCelica :: 1997 7afe 1.8 ST - P0340 Code For Camshaft Position Sensor
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesJimmy :: 95 Running Rough / Stuttering - Camshaft Position Sensor Code
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 RepliesGolf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: 2004 - Camshaft Position Sensor Error Code
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
Tacoma :: 1997 3.4L Toyota - Multiple Camshaft Position Sensor Failures / Code P3040
I have a 1997 Toyota Tacoma 3.4L ... After having some problems a week ago with the truck dieing at every stop sign or any time my foot wasn't on the gas. Eventually the truck would not start at all. I finally got a CEL that gave me P3040 (Camshaft Position Sensor Circuit Malfunction) So I changed out the sensor and the truck fired right up and ran for 3 days.. Now the truck does not start again and I am getting the same CEL code.
View 1 RepliesLexus ES 2007-12 :: Code P0365 - Camshaft Position Sensor Circuit Malfunction On ES350
I have a 2007 ES350 with 90k miles. Purchased in August. I had ignition coil go out and decided to change them all and the spark plugs. When changing cylinder 5's coil and plug, I tried to push the wiring harness out of the way to remove the coil. Result, I moved the wiring harness too far and disconnected the 3 wires (black, yellow and red) that were connected to the cam position sensor connector. (I should've just removed the sensor SMH) I disassembled the connector, got it down the internal pins, soldered the pins to the wires, placed the pins back in the connector and reassembled it with the wires in the order that they appeared to originally be.
Plugged it back in and put everything back in place. Started the car and code P0352 was cleared but replaced with code P0365 Camshaft Position Sensor B - Bank 1 Circuit Malfunction. I'm thinking, either I put that pins back in the wrong order or one of the wires isn't properly soldered in. Either way, I ordered another connector and it should be here tomorrow. I need Either a wiring diagram or a picture of the camshaft position sensor closest to cylinder 5 connected with the wires in the proper order .
Sonata NF (2006-10) :: GLS Error Code P0011 - Camshaft Position Sensor Was Detecting A Fault
My check engine light came on the other day, and I went to Autozone to have the code read. Of course, that indicated the camshaft position sensor was detecting a fault. I read through all the posts relating to the fault, headed up to my local Hyundai dealer, and picked up the oil flow control valve for about $50 plus tax. While I was there, I figured I might as well have them do an oil change, since it was way past due. No point in putting in a new part with dirty oil..right? They did the oil change, washed the car and I was ready to roll. My plan was to replace the part myself, but magically, the check engine light has not come back on since.
View 8 RepliesSanta FE SM (2001-06) :: Taking Multiple Tries To Start - P0340 Camshaft Position Sensor Circuit Code
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
Civic - Honda :: Engine Swap / Camshaft Position Sensor Replacement?
I had an engine swap recently done on a 2005 Honda Civic, and within a couple days, Check Engine light came on. Mechanic ran the error code and I have to apparently replace the camshaft position sensor. They are claiming that the sensor was not replaced in the engine swap, and so not covered by any warranty.
View 10 RepliesGolf IV / Jetta IV :: Engine Dies At Startup / Codes For Camshaft Position Sensor
I've got a 2003 Jetta Wolfsberg that is acting up, I'll do my best to describe and outline the steps I've taken with the mechanic to fix the problem,
Occasionally, when starting the car one of two things happens, (1) engine turns over, fires, and then dies. Removing the key, letting the car sit for 30 seconds and trying again usually gets the car started. (2) The car will start but will run VERY roughly (misfiring, sounding like the engine is choking out). Very much like this (only sometimes much worse, usually ending in a stall): [URL] ....
Turning the car off, removing the key, letting it sit, and then trying it again will eventually work, even though it might take a few cycles. Once the car gets running it almost always runs fine from thereon. (There have been a couple occasions where the car has gone into limp mode, even on the freeway. Pulling over, letting it sit, and starting it again almost always fixes the problem. I've not yet been stranded.)
Diagnosis & Steps taken:
I get regular codes for the camshaft position sensor and also for the MAP (Barometric pressure) sensor. Both have been replaced.The MAP sensor and the atmospheric pressure readings are off by about 30 (something like 960 and 990). My mechanic thought that maybe it was an electrical problem, he noted that the two sensors mentioned above share a common ground. He replaced the ground because it looked corroded. This brought the pressure numbers both to 990 and the car ran perfectly for a few weeks.One thought was to splice in a new wire to the MAP sensor, to see whether it was a signal problem, this hasn't been done yet. Another possibility was that there is a problem with the ECM.
I THINK, that the problems began just after having the computer flashed at the dealership two years ago. I'd got a code about an update and so the dealership did this. I don't know whether this could have had any effect on these problems, but the times lined up too well to not mention it.
Golf/GTI VI :: Camshaft Position Sensor Oil Leak
Wasn't there a TSB for this? I've searched Google and Vortex with nothing for the MKVI but I could swear I read something on this.
I am accumulating oil/grim right around the sensor and it's beginning to irritate me. I want to take her to the dealer but would rather know for sure of any possible TSB out there so I have something to reference.
GTI 337/20th Anniversary :: Where Camshaft Position Sensor Located Under The Hood
The CEL just came on in my 20th AE Gti. The code indicates a Camshaft Position Sensor issue. Don't know where this sensor lives under the hood of the GTI? Is an easy enough fix for a beginner to attempt? (have hand tools, former bike mechanic, but no shop just a parking lot in the Texas sun!)
View 6 Replies