C/K :: 1991 C1500 2wd - Truck Runs Good For 20 Minutes Then Dies And Won't Start Until Next Day
It is a 1991 C1500 2wd, ext cab, short bed 5.7L engine with about 300k miles on it that I have had for a year. Supposedly a different 350 engine and transmission was put in a couple years ago.
This problem has been going on for 2 weeks. I'll start the car up and it runs just fine, no problems. After driving for about 20 minutes, the engine will die while driving, and will not start back up until the next day. I have sat in the car for literally 4 hours patiently waiting for it to start. I'll turn the key and the engine will rotate, but will not start. When someone shows up to give me a jump after the battery gets low, it will not start. I'll go home and go to sleep, and sometime the next day I'll go to my truck, and it will start back up, and I'll drive back home, and I'll make it as long as it takes less than 20 minutes.
It is not just a "morning problem", but a "first time I have started the truck that day" kind of problem. Last week, it happened to me in the mornings. On Saturday, I didn't leave my house until 2pm and the problem happened. Today, I first drove it at 8pm, and the problem happened.
Things I have changed so far (mostly from Autozone):
Starter - burnt it out when it first died 2 weeks ago, now I know not to crank when below 9 volts - lifetime warranty
Spark plugs - no more engine popping or driving with 2 feet - changed last week on Tuesday - AC Delco CR43TS gapped at .035
plug wires - changed all in November, since I noticed one of the old ones was tore - lifetime warranty
Distributor cap and rotor - changed last month when the engine started popping - autozone
Ignition control module- I changed today, I really thought that would fix the problem after speaking with the Autozone guy - lifetime warranty
Ignition Coil - changed last month because of popping
Fuel Filter - changed last Thursday, thinking it was a fuel problem
Here are some of the other symptoms I have been noticing over the last couple months:
Pretty bad gas mileage, I know it is a V8, but it is just as thirsty when I am not carrying anything as when I am pulling a car. A couple months ago, after driving for about 30 minutes or so, the engine would make a "Pfft" noise and would start popping and I would have to drive with 2 feet to keep the engine running.
Touareg :: Truck Not Releasing Key Upon Shutoff
2011-2012 Touareg had issues where the truck does not release the key after you shut off the ignition? We're having this problem about every ~5 or so times we shut down the truck.
I have to restart the engine and turn it back off before it releases.
Am I doing something wrong with my touch, or is it a known problem where I should take it to my dealer.
Ford Fuel System :: 1990 E250 - Fuel Shutoff Switch Not Activated?
My '90 E250, open road, mini motorhome , says on the radiator mount , that there is a Fuel shutoff switch that may have been activated.... I don't have the manual for it, so I need finding the switch, so I can reset it ....The vehicle sometimes starts after about 2 mins with the ignition on, but today won't start, even after a longer wait. Both tanks are full...Fuel gauge not working , in either front or rear position. I can hear the rear pump,in the tank, but can not hear the front one....When I bought it last year, it ran fine after waiting to start, and both positions worked , no stalling , or shutdown.Came home about 95 miles, and it's been parked almost all the time since. I want to start it up weekly , but am having that same problem ...Today was the first time I could see the Fuel Pump Shutoff warning ...but can 't find the darn switch to try resetting .....
View 1 RepliesC/K :: 1998 C1500 5.7 - CES Light Came On And Truck Started To Shutter When Slow Down
I was driving down the interstate and sped up to pass a car once I started to slow down the CES light came on and the truck started to shutter really bad. I got it to a scanner and it said misfire Cylinder 6 and he suggested that i change the cap rotor plugs and wires since it has been a long time since it had been done. I did so and and the problem has continues. It idles real rough acts like it is going to die, then under power it smooths out a little but you can still tell it it where. Above 3000 the CES blinks until you slow down and the the scanner still says misfire cylinder 6.
View 4 RepliesChevrolet - 1500 :: 1990 - Truck Stumbles When Start It
1990 chevy silverado 4x4... My truck stumbles when you start it and within 5 seconds or so clears up and runs smooth.. I changed the fuel filter , still the same result.
View 1 RepliesFord Ranger / B-Series :: 1990 Truck Won't / Hard Start When Cold
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
Ford Fuel System :: 1990 F150 Truck Takes A While To Start Up
My truck is a 1990 Ford F150. It seems like when I let it sit for a few min that the gas just drains back into the tank and there for it wont start up that fast, it takes a while to get it going but when I shut it off and start it back up its like a new truck. It starts right up!!! Any tips on what might be wrong, maybe the gas cap is letting pressure out? Im 17 and my dad knows alot about trucks but he cant tell whats wrong.
View 1 RepliesC/K :: 98 C1500 5.7L Fuel Pressure - Spark But No Start
After replacing the intake manifold gasket for the second time, the truck would not start. Thought for sure it was my putting the distributor in wrong. After reviewing the forums, I am sure it is installed correctly. I have spark but no start. Engine cranks over nicely, but acts like it needs fuel. I hooked up a fuel gauge, turned on the key and get 56PSI. Lower than the 60 required. The pressure then slowly goes to 50 PSI. I pinched off the return hose and had the same readings. Pretty sure I need to replace the fuel pump. Is there anything else I need to check. I replaced the fuel pump a couple years ago with a Delphi unit. Maybe this is just a weak link for these trucks. My truck has a little over 100,000 miles on it.
View 14 RepliesElantra MD (2010-15) :: 2013 - Engine Shutoff While Driving / Cannot Start
2013 Elantra with 62k miles. I am dealing with a strange issue where I experience sudden engine shutoff and no-crank no-start situation when I attempt to restart. This typically happens during warmer weather (above 95F / 35C).
When the engine shuts off while i'm driving, the following symptoms occur:
-Temperature gauge (all bars) disappear
-Shift level selection disappears from dash
-stability control light is illuminated
During that state, I'm unable to restart the engine (even when the level is in park or neutral). Anytime the attempt to restart, the following symptoms occur:
-all of the above symptoms when engine shuts off
-TPMS light is flashing
-engine does not crank when attempting to restart.
-Unable to move shift lever from Park when key is in ON position, even when depressing the brake pedal (have to use shift lock release to get it out of park into neutral). Trying to start the car in neutral makes no difference.
The car stays in that strange state anywhere from 5 minutes to several hours. After that, I'm able to start the car and drive it for 10-60 minutes, until above issue repeats.
The issue is NOT any of the following:
-Battery
-Starter
I know that some users have reported a similar issue due to a bad inhibitor switch, but with that issue, only the gear selection disappears from the dash (while the temp gauge and other functions remain normal). Could it possibly be a bad ECU?
Ford Super Duty (1999-2016) :: Slight Rough Idle After Couple Of Minutes When Start The Truck
I have a 99 F350 with a V10. I just replaced all the spark plugs and a bad coil which solved the very bad misfire I had going on. I also just changed the fuel pump and fuel filter.
When I start the truck, it idles just fine, nice and smooth. After sitting there for a short bit, maybe a couple minutes, it starts to idle rough, not so rough that it's about to shut off, just a little rough. This lasts maybe a minute and then goes back to nice and smooth and stays that way.
I've thought maybe the EGR valve or Idle air control valve but I'm not sure if I'm way off or sort of close.
Subaru - Legacy :: 1990 - Squeaks From Rear Of Car 10 Minutes After Parking
I have a 1990 Subaru Legacy AWD wagon with almost 300,000 miles. After driving it for almost any length of time (long enough to bring it up to operating temperature) I'll park it, shut it off, walk away, & about 10 minutes later it will emit a loud squeak from the center rear underside of the car, almost as if something shifts position when the car heats up, then shifts back when its cooling off.
View 1 RepliesGodge - Grandcaravan :: 1990 - Jerking After About 45 Minutes Of Driving On Freeway
A few months ago, my van started jerking after about 45 minutes on the freeway. When it started jerking, the check engine light came on and the windshield wipers would come on just once. If I ignored it and kept driving, the jerking would become more frequent and violent until I pulled off the road and turned the car off, then back on. After turning it back on, everything would be normal again, sometimes until I finished my commute to work, sometimes it happened every 5-10 miles. Never any problem in town.
A few weeks later, and in addition to the previous stuff, when driving in town, the windshield wipers would come on just once when braking. That would happen a few times a day, with no check engine light and no other issues. Now, when you hit the brakes, in addition to the wipers coming on, sometimes the RPMs will drop until the engine dies. Today, it died 4 times in 10 minutes.
I've changed the very corroded ground strap from the block to the firewall, cleaned up the battery posts and cable connectors (dirty, but no corrosion), checked for corrosion in the wiring harness underneath the battery and I'm not finding anything.
Chevrolet - Celebrity :: 1990 - Dies Without Warning / Starts After Five Or Ten Minutes
I've had my car die twice on me lately. There is absolutely no warning - no sputtering, rough-running- just dies completely. I am still able to crank the engine after this happens, but it won't start immediately. After five or ten minutes, it will start and then run fine. 1990 Celebrity. what this could be and how to fix it?
View 1 RepliesToyota - Camry :: 1990 Takes Literally 3 Minutes To Engage Reverse
A140E transaxle issue... I have what I surmise is a direct clutch engagement issue. It takes (literally) 3 or MINUTES to engage reverse. And obviously the 2 -3 shift is slow also. It acts like there is a restriction in the passage to the direct piston. I rebuilt about 5 years ago, so am familiar with the teardown.
View 2 RepliesChevrolet - 1500 :: 1990 - Truck Is Backfiring
Just got a 1990 k1500 with the 4.3 v6 and 5 speed and it backfires. A buddy told me it was shooting flames out of my exhaust. What does that mean?
View 7 RepliesChevrolet - 2500 :: 1990 - Truck Stalls In Reverse When Hot
I have a 1990 chevy K2500 5.7 350 tbi with 255000 miles on the body and engine. transmission replaced at 200000. When I drive long enough for the truck to get hot (i.e., 10 minutes or so) if i put it in reverse to back into a parking space or my driveway, it just shuts off. i have had fuel filter and fuel pump replaced but what could cause this? it will stay on if I don't drive long enough to get hot.
View 1 RepliesChevrolet :: 1990 Truck Dies At Random While Driving
My truck is having a problem lately where it will suddenly die while driving. It feels like it loses either spark or fuel and happens about 20-30 minutes after I drive it. Once it dies you can turn the key off and restart it and it will fire up and run again, for how long I'm not sure because I'm almost home about that time. It has a fairly new fuel pump, 2 years old, a fuel filter the same age, new cap and rotor, new air filter, probably could use some new plugs. I replaced the TPS with an older one that I had laying around and had no change in performance. I get a 34 and 43 code (MAP and knock sensor) when I do a diagnostic on it.My question is do you think a MAP sensor or knock sensor would cause this kind of failure before I go out and buy them? I'm leaning towards the MAP sensor but not sure that it would have this kind of an effect on the engine.
View 4 RepliesToyota :: 1990 - Truck Radiator Runs Dry All The Time
I have a 1990 Toyota pick up and, even though I have had the radiator removed and tested twice for leaks, I still loose fluid. I drive 30 miles - after having filled the radiator to the top - and then find it empty. The overflow radiator fluid bottle is always full to the top but the radiator will not stay full. My radiator man has told me to place a large piece of cardboard under the car to see if there are any leaks - there are non. I pay more in coolant than I do in fuel!
View 8 RepliesFord Ranger / B-Series :: 1990 - Rough Idling / Truck Dies
1990 Ranger 2.3L 4 cylinder. The truck idles so rough it dies. It runs fine going down the road it just seems to "load up" at idle. I know there are hundreds of things that it could be, I just hate to start throwing parts at it. It is definitely running rich at idle.
It is one of those trucks that we have replaced a lot of parts. The scan tool said something about setting the timing??? Is there a way to set the timing? There is no distributor, and it is the one with 2 coils and 8 plugs.