Accent MC (2006-11) :: Getting P0012 Code
I am getting a poo12 code on my 2007 hyundai accent. All the sensors seem to be fine. How to get it fixed?
View 9 RepliesAccent MC (2006-11) :: Misfiring On Idle - No Code
Recently got broadsided (passenger), got the body fixed up. Now it is Misfiring on idle and only on idle...
Prior to this I had Coil go out on me, got that changed out, changed the spark plugs. It was running great then the accident happened an this Misfire on idle problem.
Took it to the shop, had them check for a code, no code. They suggested that it made be do to carbon buildup from the previous misfiring issue and suggested using STP engine treatment on it.
Accent MC (2006-11) :: Gas Mileage Went Up - Code P2096
This is in regards to a 2007 Accent 111k miles, about 3 weeks or so .. I had a p0420 code, and replaced the downstream o2 sensor, and the CEL went off, and gas mileage went up. Now today I got p2096 code. Seems to mirror the p0420 code. So now I am thinking the catalytic converter.
So my questions are:
There are two catalytic converters right? one would be the exhaust manifold and the other would be half way through the exhaust system after the two o2 sensors?
Which should be replaced in regards to p2096?
Could anything else be causing this code?
Accent MC (2006-11) :: Check Engine Light Has Been On - Code VSS
My check engine light has been on for months and the only code coming up is for the VSS. I got the VSS replaced and the light came back on as soon as I hit 70 on the freeway. Checked the code again and the same one came up. Is this a common issue with 06 Accents? I'm wondering if it might be a wiring or computer issue... My ABS light is also on, would this have anything to do with it?
View 5 RepliesAccent MC (2006-11) :: Misfire With Error Code P0302
2009 Accent, 1.6L 154,xxx Cylinder two misfire. Engine was rebuilt due to timing belt. Twice. Second time I did it. Replaced plugs, coil packs, all gaskets, (everything new in the head) did a smoke test, compression test 180 psi across all four, used a noid light for coil packs (good) did it at the injectors 1,3,4 did good, but 2 came on then went off. Check resistance and it shows good, replaced injector anyway and the connecter. Still doesn't work. Checked powers and grounds at the rail, good. Good solid voltage. I hooked up a scan tool and tried to shut injector 2 off, no change in RPM or vibration. Scan tool worked for 1,3,4. Used another PCM, still misfire in two. Even jumped a wire from PCM control and 15A inj fuse for the 12V constant (bypassed the harness) and still doesn't work. Also have knock sensor code, just two codes.
View 14 RepliesAccent MC (2006-11) :: VSS Code PO501 - No Faults Found
Have VSS code PO501. Have fitted new right vehicle side speed sensor, after reset code clears but quickly returns so still got code. Speedo is working. Have sent ECU for testing - no faults found.
Car is an auto, can the left/drivers side sensor cause this or the transmission sensor cause this?
Accent MC (2006-11) :: Code P0339 - Car Stalling While Idling
Twice today my car stalled out while idling. Once at a left turn red light and once in the drive thru. The first time it restarted after about 10 minutes. The second time it restarted after about 2 minutes.
Car is throwing cod P0339 for Crankshaft Position Sensor A Circuit Intermittent.
I did some reading up on this on the forums but didn't do much about it. I just tried wiggling the wiring and all that when idling, didn't notice any roughness or stalling so.... may not be a connector issue.
Anyhow, planning to take it in for diagnosis and repair as it's really not derivable the way it is.
Actually this is the first time ever the car has given me engine trouble of any kind. just passed 90,000 miles. Shucks, streak broken.
Accent MC (2006-11) :: 2010 GL - Misfire On Cylinder 2 / Code P0302
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
Accent MC (2006-11) :: 2008 - Code For Cylinder 1 Misfire / CEL Flashing
I have a 2008 Hyundai Accent that is giving me one heck of a headache. I keep getting a code for number 1 cylinder misfire. When you start it up it runs fine for a while then the CEL will flash and it will start running rough. As soon as I shut it off and restart it, it runs fine. I even experimented with it this morning on the way to work. It started running rough doing 60, I put it in neutral, turned the car off and then right back on, put it back in gear. It ran fine the rest of the way to work. I have swapped coil packs, fuel injectors, spark plugs, and have even hang tested another ECM. Still number 1 cylinder misfire.
View 8 RepliesAccent MC (2006-11) :: CEL Code P0420 Bank 1 Popped Up While Driving
P0420 bank 1 code popped up while driving. Im thinking this is just an oxygen sensor? Is it ok to drive with this code for a while if i buy an o2 sensor online?
View 5 RepliesAccent MC (2006-11) :: Shuddering When Vehicle Is Placed In Gear - Code P0301
When looking at the engine from the front of the vehicle. what numbers are the cylinders from left to right? To curtail off of that question where do I locate the corresponding ignition coils to these c I have been dealing with intermittent misfires on cylinders 1 and 3 codes P0300, P0301, P0303. I replaced the spark plugs to no avail. Whenever the vehicle shudders the headlights dim and the shuddering is worse when the vehicle is placed in gear, the A/C fan is on, or the vehicle is accelerating. Once I reach a certain speed, usually 35-40 mph, I don't notice until I again slow down. I replaced the spark plugs the day after I had the first issue appear which read code P0301. Prior to installing the spark plugs, I experienced a severe loss of acceleration power, but now only experience the shuddering.
2011 Hyundai Accent 63500 miles ....
Accent MC (2006-11) :: Got A Check Engine Light Code P0139
I did a spirited sprint from a stop light and then got this cel. It says it's for the second 02 sensor. I got home, jacked it up and checked it out. Everything looked, sounded, smelled, ran fine. What should I do?
View 28 RepliesAccent MC (2006-11) :: CEL Code P0171 - Misfires With Full Throttle
My accent 2006 has the check engine code p0171. AT mornings I have to start the car like 5 times until it revs up and do not stall. Also when the car is running, If I press the gas too much it starts misfiring and have really slow acceleration. I have already change the 02 Sensor, spark plugs, TPS and maf sensor, and PSV valve, cleaner the throttle. I really don't know what else to look for.
View 5 RepliesAccent MC (2006-11) :: 2010 - Code P0303 And Rough Idle After Filling Up
I just bought a 2010 Accent for my daughter and this was the 2nd time I filled it up. I realize now I should not have topped it off all the way but I did. The tank was probably bone dry when I filled it up as well. Within 5 miles after I filled it up, it started running rough and the check engine light came on. I stopped it and checked around under the hood. Checked to make sure the gas cap was tight. I drove it again and it appeared to run fine. I stopped by an Autozone and had the code checked. It was a misfire code for cylinder 3.
Drove it home (10 miles) and parked it. I took the battery terminal off and cleared the CEL. When my wife drove it a few minutes later, the CEL came on again and it started running rough. Had the code checked again and the cylinder 3 code came back. The guy at Autozone said over-filling the tank when it was empty probably caused too much pressure on the fuel going into cylinder 3 and that it should correct itself in the next few days. I drove it 20 miles to work today without any problems. It seemed like it had to be related to filling up the tank since it happened a few minutes later.
Accent MC (2006-11) :: 2009 - Code P0300 / CEL Came On And Stayed Over Multiple Startups
Had the CEL come on twice in the last few days. The first time, a restart of the car took it away. The second time, it came on and stayed over multiple start ups.
With Torque Pro and a bluetooth OBDII dongle I read: P0300 - Powertrain, Random/Multiple Cylinder Misfire Detected
From the Internet:
Possible causes
- Faulty spark plug (s)
- Faulty ignition coil (s)
- Clogged or faulty fuel injector (s)
- Intake air leak
- Fuel injectors harness is open or shorted
- Fuel Injectors circuit poor electrical connection
- Ignition coils harness is open or shorted
- Ignition coils circuit poor electrical connection
- Insufficient cylinders compression
- Incorrect fuel pressure
I wish it wasn't so broad... But, as the car is about to hit 60,000 miles, I plan to replace the spark plugs (NGK), engine air filter, cabin air filter. Just had the timing belt done last week. I will check all of the intake couplings for tightness.
For others who use Torque, what other settings could be useful in pinning down this issue for me? I cleared the CEL this morning; it didn't come back yet.
Accent MC (2006-11) :: Engine Was Idling / Little Rough And P0302 Code Thrown
So I bought my accent used a couple months ago. It is a 2007 SE 3dr 5spd manual. It ran nice during my test drive and the price was right so I bought it.
Now I'm wondering if there is any way to find out the service history on the car...at least the major one's (30k, 60k)?
I ask because recently the engine was idling a little rough and it threw a P0302 code so I changed the spark plugs and holy-cruddy-deposits-batman those things were black. Gapped the new ones and popped them in and its a noticeable difference. My CEL keeps coming on and throwing a P0496 code as well, virtually once every tank of gas. Its not the gas cap so my next step there is to check the PCSV and hoses.
With these little problems, it makes me wonder about any larger issues. I know the timing belt on these things is supposed to be replaced at 60k. Additionally I would be willing to bet that my ECM software is out of date. Would Hyundai have records for any of the big maintenance milestones since they are required for warranty work?
How much does it cost to have a dealer check your ECM software and update it if needed?
Accent MC (2006-11) :: Hard / Jerky Shift - CEL Showing Code P0717
My 2009 Accent started doing the Hard/Jerky shift problem that I seen discussed in the forums. Had check engine light, scanning showed a code P0717. My question is, which sensor should install?
View 4 RepliesAccent MC (2006-11) :: 2007 GLS - Random / Multiple Misfire And Code P0300
I have a 2007 Hyundai Accent GLS. I just got it from a used car dealership (local) and it runs perfectly. It had a misfire code when i first got it, for all cylinders plus the p0300. It went away when i started the engine again, and didnt come back til a month later (Now). now it wont go away.
I went to advance auto and had them use their OBD2 reader for a trouble code and i got p0300, p0301, p0303, p0304. No other codes present.
I am not feeling anything bad, and from what I am told, a misfire feels like a hard shift. This is of course after getting the plugs and wires changes as well as an oil change. Standard preventative maintenance.
The mechanic used OEM parts got from local parts shop. i think the OEM plugs are the copper ones. I would have preferred iridium as they arent that much more expensive but I don't want to pay for another plug change.
The only symptoms I can think of, is that according to google, I should get around 380 miles to a full tank (11.9 capacity, 32 mpg city). I am only getting 280 from full tank to gas light.
I have also gone through a lot of oil. I checked the dipstick and it was below the low line, so i bought a quart of high mileage oil (same exact brand and type of oil that i gave to the mechanic to use) and it went to just above the full line. This was at around 1500 miles after oil change.
After visiting multiple sites about misfires, i found a few things that caught my attention. One is a site called auto service professional, which talks about the OCV for the MC accent. A lot of sites also recommend gaping the plugs at .035.
Accent MC (2006-11) :: 2007 - Check Engine Light On For Code P0446
I own a 2007 hyundai accent currently around 123,000 KM's I've got my check engine light on and it has been on for a few weeks now. The Code its giving me for it is P0446, ( Evaporative Emission System Vent Control Circuit) Is what it is saying. I also notice when I put fuel in my car it does not want to start unless i turn the key over a few times or pump the gas pedal..? What to replace for this code?
View 9 Replies