Accent LC (2000-05) :: Cranking But No Gas / Spark / Turn Over
2005 Accent has been essentially bug free until now.
Drove 3 hours, parked for 4 hours, then when to turn it on... cranked, no turn over. Tried again and the crank died. I figured, ok, no problem, battery getting long in the tooth, time for a new one.
A friend and I were able to push start it (5 speed manual), and yesterday I bought a new battery for it. No worries right?
Wrong. Same thing now. Cranking but no gas/spark/turn over. No check engine light or codes.
My next place I'm guessing I need to check is the fuel pump relay? Should I hear a click a few seconds after I turn the key to on? I believe I should, not sure if my memory is playing tricks on me, but right now there is none.
Relay in the fuse box? Do I need to check anything else first? Have multimeter.
Accent LC (2000-05) :: Intermittent No Start After Filling Up / Cranking But Not Firing Up
I have a 2000 Hyundai Accent hatchback with 98k miles. About a month ago we were headed out of town and got gas about a mile away from the house. After filling up, the car wouldn't start. It would crank but not fire. Tried for about 15mins to no avail. Had it towed to local mechanic and it started right away. They kept it for the weekend and said they had no problems starting it, so without experiencing the problem they said they would just be throwing parts at it.
About 2 weeks after my wife drove to store and when she went to leave and same experience, but this time it started after trying for a couple of mins. Then just this Tuesday it wouldn't start in the morning. When it just cranks but not fire it shows a pending P0335 (crankshaft position sensor). So I ordered the part (won't arrive til Friday). When I got home I tried to start it as well to no avail; tried again Wednesday morning and evening, nothing. Then this morning (Thursday) it starts right up. Once its started it runs great. After recurrence of no start 2 weeks ago, I replaced spark plugs and spark plug wires.
Accent LC (2000-05) :: 2002 - No Longer Start / Just Keeps Cranking But Doesn't Ignite
So my 1.6 accent (140,000) decided to no longer start. Just keeps cranking but doesn't ignite. Plugged a scanner in and it's the crankshaft position sensor. How difficult is this to get to? From what I've ready its just held on one end by a 10mm bolt and the older end is just a connector, but it looks like it might be in a pain in the ass location. Does anything need to be taken off first to access? Should this take less than 30 min?
View 1 RepliesAccent LC (2000-05) :: Stalling And Wouldn't Start Unless Pumped The Gas While Cranking The Engine
Last week I started having problems with my 05 Accent, hatchback, 1.6L engine, automatic transmission. Filled the tank up with gas and the car stalled pulling out of the station and wouldn't start unless I pumped the gas while cranking the engine. Ran and started fine after that and I thought it may have just been an air bubble in the fuel line, since there wasn't a check engine light or any other symptoms after that. Fast forward to this morning and the check engine light comes on during my commute and when I checked it, it gave an EVAP code (P0441). I also stopped to refill the gas and it stalled again as I was leaving the station. Also after I measured the gas mileage I found that I'd lost around 7 mpg (from around 30 to around 23).
I've never heard of EVAP problems causing stalling and loss of gas mileage but I'm not all that familiar with these systems so I don't really know. I'm going to test if it's the gas cap going bad since on the list of things that could cause a P0441 that seems to be the easiest place to start, but other than that where to start looking?
Volvo :: Skips / Hesitates When Cranking - Hard Cold Weather Start
We have a 2009 S60 2.5T that has trouble starting in temps around 25 degrees and below. It skips/hesitates when cranking.
View 7 RepliesAccent LC (2000-05) :: 2001 - Stumbles / Hesitates From Standstill
I have a 2001 Accent, manual transmission 1.5L. The lady who had it before me overfilled it and stuffed the charcoal canister. She had this replaced, but when I bought it she reported that it still had a fuel issue immediately after refueling. She said it would stall and run rough and hesitate.
After I bought it I took it to refuel and confirmed the problem. I had read that the ECU may be trying to draw fuel through following refueling, but the new canister might be messing something up. She used to only drive it commuting distance in a city, so I took it for a long drive. Running at steady cruising state for a prolonged period seemed like a good idea, to allow any ECU learning. This partially fixed the problem! Now, most of the time, I can leave a fuel stop without a 20km drama before the car settles down, although the problem hasn't entirely gone away and it still does play up sometimes.
There's a more pressing problem which may or may not be related, however. When launching from idle, the engine goes through this 2-5 second hesitation of no power at all. If I rev up before letting the clutch out it's ok, but there's a certain minimum revs needed to avoid the problem. This is killing my clutch, and if I get it wrong it sometimes leaves me in the middle of a busy junction with no power for an uncomfortable period! During the hesitation, I've found the best way to force it is to put clutch back in and go full throttle. After 1 second or so the revs come back. The problem is much worse when the air conditioning is on.
So the clues are:
1. the previous charcoal canister issue
2. the full throttle thing might indicate something with the TPS
3. the worsening of the problem with the a/c on
Things I've tried so far...
1. prolonged cruising; seemed to improve things after refueling but overall fueling issues not fixed.
2. disconnected the battery -ve and applied brake light circuit to drain ECU capacitor, then left for any power-hold relays etc. then reconnected battery and took it for a normal drive for 30 minutes or so. No effect.
...and things I've yet to try (all gleaned from searching this forum)
1. checking / replacing plugs and HT leads
2. checking / replacing o2 sensor
3. checking the TPS plug connections. Checking the sensor itself sounds expensive - would it involve more than standard OBD?
4. checking vac hoses, in particular the hose which draws from the cannister
5. checking alternator (not sure how); the worsening of the problem with the a/c on could indicate low power getting to injectors etc? (bit of a wild guess)
In a former life I was a diesel engine calibration engineer, so I know the tricks which manufacturers can put into ECUs. What I don't know is the tricks specific to this car.
Accent LC (2000-05) :: 2003 1.6l Hesitates To Startup Almost Every Time
I keep getting p0420 and p0112. All new parts with in the last 10k miles new battery , starter , alternator , spark plugs , 02 sensors both bank 1 and 2 , catalytic converter aka exhast manifold , new map sensor , timing belt
The car drives fine it just hesitates to start up almost every time. Car has 210k miles
Accent LC (2000-05) :: Engine Would Turn Over But Wouldn't Start
o my wife was driving our 2005 Accent GLS with about 95k miles yesterday, and it had an issue that it's had three or four times before: the engine would turn over but wouldn't start while it was still warm. In the past when it happened, whoever was driving would wait a few minutes and try again. It always started on the third or fourth try after waiting five to twenty minutes.
Yesterday, however, she was frustrated and so called AAA to have them send a battery truck over and have them take a look at it. The truck came relatively quickly, and they started their diagnostic procedures. The battery was fine (knew that), and he tried all the standard things like cleaning the terminals/harnesses and whacking the starter with a hammer. My wife said that as she and the tech tried to start the car, the turn-over seemed to get shorter and shorter- so when she first tried it would turn for a few seconds, and after a dozen or so attempts it was only turning for a second or less.
Finally, the tech (who apparently seemed to be frustrated at this point) got behind the wheel while my wife was looking under the opened hood and turned the ignition on and held it. The positive battery terminal apparently started smoking and my wife had to yell at him to get him to stop.
After this point, the engine no longer turned over at all. He tried a few more things like cleaning the cables, but no change. He finally said that he would call for a tow truck, and we ended up getting it towed back to our house.
The problem is unchanged since yesterday: there is full power when in ACC mode, but when you turn the ignition all the way to the on position there is nothing but a single loud "click" and a high-pitched whining noise.
I left my ODB bluetooth interface at my office, so I haven't been able to see if there are any codes.
Accent LC (2000-05) :: 2004 Won't Start / No Click Or Crank When Turn The Key
I just bought a 2004 hyundai accent 1.6L standard transmission on the 13th of June, ran great drove it everyday, was driving fine when I came home monday night, went to drive it yesterday and get nothing, turn the key no click, no crank, the radio turns off as it always did when you try to start, I checked the fuses, and the battery shows twelve volts on the meter, what could cause this to abruptly happen?
View 3 RepliesAccent LC (2000-05) :: Starting After 5 To 6 Seconds Of Cranking When Engine Is Cold
I have a 2000 Accent with 90k miles. The last week or two, it takes about 5- 6 seconds of cranking to start when the engine is cold. Having had the car since new, I know that it's not normal.
The engine seems to crank strongly, and once started idles and drives well. This occurs once about every 4 starts when engine cold. Warm engine starts normal.
Changed plugs - no difference. Maintenance current per owners manual schedule.
Accent LC (2000-05) :: Crank Position Sensor Shows No Resistance When Cranking
I'm working on a family members car. We pulled out the old motor and put in a new one because the old one has rod knock. We're not getting ANY spark. Crank position sensor shows no resistance when cranking. The harness at the crank position sensor shows no voltage. The both coils measure 1.5ohms.
The only two bits of the harness that are in questionable locations are the grounds next to the ignition coil and the passenger side strut tower ground. I have the strut tower one to the closest bolt on the intake manifold and the coil pack grounds to the coil pack bracket.
The car has plenty of fuel and good cranking speed, just no spark. I verified using a timing light (no flash) and spark-plug short-to-ground. The old engine WAS running and all of the sensors on this one were swapped over from the running one. Also, the tach doesn't move when cranking.
Is there something that's commonly overlooked, or something that could be causing the issue searching showed it could be the crank position sensor, but like I said, I pulled the working one off the running engine.
Accent LC (2000-05) :: Engine Light Blinks Before Cranking / Car Struggles With 1st Gear
I own a manual accent from the 2000 that I have since last December. Fuel pump and battery are new, I changed them after getting the car.
The issues I have and I think they are due to the same reason, are the following.
1. Sometimes, when I turn the key to on position and before cranking, the engine light blinks and the car wouldn't start. Then I remove the key and try again until the light doesn't blink and then the car would start. This could be the second time, the third time or after several times. When the light blinks and I try to start the car, I can hear the fuel pump and the battery working, so the problem must be somewhere else. Also, this issue happens very randomly, it may doesn't happen during two weeks and then it happens one day and next day is OK again.
2. Few times it happened that even if the engine light wasn't blinking, the car started but like without enough power and then it stalled, I tried again, and it has always started OK the second time.
3. A couple of times, I was on the road and stopped the car in a red light and it stalled when I switched to neutral.
4. The car sometimes struggles with the first gear, when I'm switching from neutral to first gear to start the car (after being stopped in a red light for example). The car would start very slowly, even if I'm pushing the accelerator and don't have my foot on the clutch anymore. But after few seconds, the car runs well and I switch to second gear, third gear, etc. and runs perfect. Above 10-20 km/h the car runs perfect, I only have issues (sometimes, not always) at very low speed in first gear.
I think that's it. So far, my mechanic has checked the code problem and he coded a new key, thinking that it was a communication problem between the key and the engine, but it didn't solve the problem. I don't know where to bring the car, because every time someone checks it, they can't find the problem or a solution and I don't want to spend more money for no reason. But I'm also worried that the car breaks down one day in the middle of the road or when I'm in the field with volunteers (I need the car to do field work, but luckily it's not a remote area.
Accent MC (2006-11) :: 2009 - Cranking Slow / Taking Longer To Start
On my 09 accent, it's been cranking slow/taking longer to start. Occasionally it won't even have the guts to spin the starter (clicking solenoid noise).
I checked the battery (<1 year old), and it has a resting voltage of 16.2 (?!) When running, it jumps to 17.4. Is this a bad alternator?
Santa FE SM (2001-06) :: When Turn The Key To Start - No Cranking / Clicking And Sound
This past winter I started having trouble with my '06 Santa Fe where I would turn the key to start my car and nothing would happen. No cranking, no clicking, no sound. My lights turn on fine, radio, everything else works just fine. Sometimes it won't start for 30+ minutes, and sometimes I'll just try a second time and it'll start up right away.
Last winter when this happened my check engine light came on and so I took it to the dealership and they said it was the crank position sensor that needed replaced. For whatever reason I didn't get it fixed and have been driving my car with no problems whatsoever for 10 months or so, until this weekend when my no start issues started again. The check engine light is on again and it's the same code for the crank position sensor.
I believe I will definitely get the crank sensor fixed this time, but could the issue possibly be anything else? Bad starter? Ignition switch? My mechanic can't give me a definite answer because every time I take it to the shop it starts up just fine for him.
Ford :: Engine Doesn't Turn Over Or (Despite Cranking Fine) Won't Start
RE: FORD PROBE GL (non-turbo). Last week suddenly car wouldn't start Thurs. night. Cranked but would not turn over. Heard click at ignition switch area when key turned to start position. (Although I could only hear one click from inside the vehicle with windows shut, I was told that clicks audible under the hood from standing outside.) Tried jump starting (from a good battery using proper connections) unsuccessfully, repeated tries several minutes apart, allowing longer and longer time to charge. About every third attempt, instead of cranking sounds, I would get silence, with only the click audible.
Temperatures decreased from approximately 50s to 20s when symptoms began.Battery is old but tests good/replace soon: 330+ CCA at 43 degrees, original rating CCA 530 (silver battery now at 7 years. Will replace, but garage did not have required size 56). At that point, the amps gauge read at the low end of the normal range (and today it read mid-way in the normal range).Had car towed to garage on Friday. Mechanic looked at on Saturday and decided it was the inertia switch, which he said had "tripped".I watched video for technicians on inertia switch but it shows on newer Fords. Mine is not located at the kick panel and does not have a red button on top. I am not certain from my experience whether the reset button would actually be in a different position when tripped or he merely surmised that is what had happened, despite my telling the shop manager that I had not so much as bumped a curb. Also, the trunk was not slammed or even opened prior to the car not starting.
Car presumably started fine at mechanic when they pulled it into the garage to put air in tires and back out to the lot, as well as when I started it to drive home on Sunday. However, on Tuesday it would not start. Just in case, I depressed inertia switch reset and tried cranking again several times, giving it some gas, until I was actually pumping it vigorously in desperation as a last resort (several seconds turning key each time), and on about the 5th try, the engine began to catch just as I was releasing the key. Reset the inertia switch one more time (just in case), and after a couple more attempts, it finally started, but when I was going in reverse to back out and then putting in gear to start out in first gear, for about 15 seconds total, I heard a bizarre loud, fairly high-pitched whistle/whine type of sound that seemed to come from under the hood coming through the central area of the dash where the radio is located.
Drove about 5 miles to my job, and about 2 hours later was able to start the car on the first try. Lately usually driven relatively short distances of 2-4 miles, with a longer drive of 11 miles broken up into 6 miles + 5 miles on the return trip the night before this started happening.
Accent LC (2000-05) :: Suddenly Died When Making U-Turn / Vacuum Noise When Turn The Key
I have a 2001 accent 5-spd. I was on my way to work and I was making a u-turn when the car suddenly died. I tried to start it back up but it didn't even sound like it was turning over. I tried to bump start it or do a rolling start and nothing. I had to go to work. When I returned to it 8 hours later I again tried to start it and nothing. When I turn the key it makes a "whirring" or "humming" noise, kind of like a vacuum noise. When I had someone else try to turn it, I noticed the belt was turning, but the engine wouldn't crank or make any attempt to turn over. Just the belt was spinning and no engine crank. What could this be?? Could it be the crank position sensor?
View 1 RepliesInfiniti - I30 :: Starter Clicking When Turn The Key / Car Doesn't Sound Like Cranking Or Even Trying To Start
I drive an Infiniti i30. When I bought it, the guy who sold it to me told me that the car runs great but that I would have to turn the key kind of hard to get the car started. Over time, this problem has progressively gotten worse. There have been times where I'd be stuck in a parking lot for over an hour trying to get the car to start. When I turn the key, I can hear the starter clicking, and all of the dash lots and radio will come on but the car doesn't sound like its cranking or even trying to start. The weirdest thing is that the first time I drive my car in the morning it starts up just fine. It's once I turn the car off after driving somewhere and try to start it again that I have problems. I'll have to turn the key 100 times or more sometimes to get it to start if its not the first time of the day. What this could be?
View 4 RepliesAccent LC (2000-05) :: Car Will Turn Over But Not Get A Spark
I'm completely lost. My car won't start. It will turn over but not get a spark. I replaced the plugs and the camshaft position sensor and still having issues. I didn't change the wires when I did the plugs. Would that cause the problem to persist?
View 29 RepliesAccent LC (2000-05) :: Frozen Ignition / Car Won't Turn On
So this morning, it was -5 degrees outside. I put the key in the ignition, but I could not turn it forward at all, it was like it was frozen. So I took a lighter, heated up my key, and put it in the ignition, let it set for a few seconds, and I was able to turn it over. I have had to this every winter so far, but it only happens when it is really cold out. The only thing I can think of is moisture in the ignition.
View 3 Replies