Ford - Explorer :: Heater / AC Only Blows Out Through Defrost Vents No Matter What Setting It Is On
My wife's '02 Explorer has developed an issue with the heat/AC. As far as I can tell, the heat is hot when it's supposed to be hot, and the AC is cold when it's supposed to be cold. But, the problem is that everything only blows out through the defrost vents, no matter what setting it is on.
I know there are other threads on this type of subject, and I have read a lot of them. I thought I had identified that actuator gizmo as the culprit, but the more I read, it didn't seem like the symptoms for that issue are exactly like mine. I want to try and fix it myself, and I'd love to take the time to read everything on the subject, but warmer weather is here and my wife wants it fixed yesterday!
This problem reminds me of the time the vacuum pump went out on my F-350 and the defrost vents were all that would work. I wish this problem would be as easy to fix as that was.
Ford Escape / Hybrid :: 2008 - AC / Heater Blower - Air Only Blows From Front Vents Towards Face
The ac/heater works just fine. But the air only blows from front vents towards face; even if i press button to defrost or floor or frontnfloor.
View 1 RepliesSilverado :: Cold Always No Matter Where The Temperature Selector Knob Turned - No Heat
I have a 2010 chevy silverado. No matter where I turn the blower selector switch, it always comes out of the vents. Also no matter where I turn the temperature selector knob, it's always cold. It's a company truck that I can't get fixed soon because of downtime and I'm not supposed to take it to get fixed on my own time. It was 37 degrees this morning on my drive into work.
View 4 RepliesFord Escape / Hybrid :: 2008 - A/C Malfunction - Air Only Blows From Front Vents Towards Face?
The ac/heater works just fine. But the air only blows from front vents towards face; even if i press button to defrost or floor or frontnfloor.
View 7 RepliesFord F-150 - 1997-2003 :: No Heat / Blows Cold Air No Matter What Setting At HVAC Controller?
My brother-in-law has a 97 F-150 with 4.6L that has no heat in the cab (blows cold air no matter what setting at HVAC controller). Heater core was replaced one year ago and T-stat was replaced last night. Coolant level is full and the heater hoses are BOTH hot so I believe warm coolant is flowing through the heater core. I am thinking that the HVAC controller may be at fault or maybe the mixing door in the HVAC plenum is malfunctioning. I have 97 rangers that had a broken hinge pin for the mixing door inside the plenum (a common problem with these trucks), maybe this is the same issue (I don't know). I am taking the whole dash out to see what the trouble is.
View 9 RepliesChevrolet - Blazer :: Heater Control Only Work For Defrost And Face-vent Operation
2000 Blazer LS 4X4. 186k miles. It would seem that my heater control will only work for defrost and face-vent operation. (Just happened yesterday) When I move the controller from the off position to defrost, I can hear the system moving the flaps into position. But it no longer moves for defrost/floor or just floor control. Would changing the heater control solve this problem, or could it be a bad vacuum line?
View 12 RepliesAccent LC (2000-05) :: How To Reset A Throttle Position Sensor
I was reading the car's settings using the Torque app and an OBDII bluetooth dongle and I realize that at WOT the ECU is only seeing 85% from the TPS. O know on some vehicles there is an actual procedure like turn the key forward, hold the gas pedal at WOT, turn the key all the way forward w/o starting while pulling the turn signal stalk down or something crazy like that to force the ECU to re-measure while you keep the gas pedal pinned to the floor. I know on other cars when it doesn't read a full 100% you miss out on a small amount of power and MPG so if it's an easy procedure with these cars I'd like to reset it. I did some searching but mostly came up with info on how to replace it and a few related subjects but noting on this specifically for this car specifically.
View 2 RepliesAccent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesAccent LC (2000-05) :: Camshaft Position Sensor - Circuit Low Input
My 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 RepliesAccent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesAccent LC (2000-05) :: Heater Not Blowing Enough Heat
My heater seems to not be blowing as much hot air as it used to in my 01 Accent GS 1.6 L. The air is warm, but it is not warm like it is supposed to be. All selectors work well eg. fan speed and temp selector. Engine is running normal operating temps too. So in the end, it takes forever to get warm in the car, and to keep it nice and warm, it has be on fan speed 3. if not, the car will lose the warm air faster than it can push it out.
View 3 RepliesAccent LC (2000-05) :: Crank Position Sensor Shows No Resistance When Cranking
I'm working on a family members car. We pulled out the old motor and put in a new one because the old one has rod knock. We're not getting ANY spark. Crank position sensor shows no resistance when cranking. The harness at the crank position sensor shows no voltage. The both coils measure 1.5ohms.
The only two bits of the harness that are in questionable locations are the grounds next to the ignition coil and the passenger side strut tower ground. I have the strut tower one to the closest bolt on the intake manifold and the coil pack grounds to the coil pack bracket.
The car has plenty of fuel and good cranking speed, just no spark. I verified using a timing light (no flash) and spark-plug short-to-ground. The old engine WAS running and all of the sensors on this one were swapped over from the running one. Also, the tach doesn't move when cranking.
Is there something that's commonly overlooked, or something that could be causing the issue searching showed it could be the crank position sensor, but like I said, I pulled the working one off the running engine.
Accent LC (2000-05) :: Power Windows Failure - Window Stuck In Down Position
In May the driver's side window mechanism (motor + "window regulator" are the primary parts) self destructed on my 2002 Hyundai Accent and left the window stuck in the down position. Since the car only has 35,000 miles on it, and since I live in a cold climate and didn't lower the windows much, I concluded it was a manufacturing failure.
So rather than spend about $700 to have the mechanism redone, I elected for 1/10 as much money to have a body shop remove the mechanism and wedge up the window in the up position permanently with blocks and screws. Since I was told by a couple of mechanics that this type of failure occurs in other vehicles, I was still sticking by Hyundai and planning to buy another one 3-5 years from now.
But I have been forced to change my plans. Today (in September) the passenger side window mechanism self destructed and, once again, left the window stuck in the down position! Naturally, I am going to have the same solution applied to the passenger side window now. As a result of this (and an unbelievable brake problem that I don't have time to get into) I have been forced to change my mind and can no longer support Hyundai.
Accent LC (2000-05) :: 2003 - Repeated Crank Position Sensor Failure
I've got an '03 Accent 1.6 in the family. December 2011 I replaced the crank position sensor and it cured the no start problem. Got it from A/Zone. It lasted 2 years and 8 months. Then, the same thing happened again in August 2014 only this time the car stopped running while on the road and I had it towed to a local garage. They installed a "Standard" & was back on the road again when it stopped running again a week ago. Had it towed to my house this time and read the code. P0336 CPS again! That sensor lasted only 4 months. The garage came & replaced the sensor & it's back on the road...for now. Do these cars only play nice with Hyundai CPS's or should I be looking for an underlying issue?
View 7 RepliesAccent LC (2000-05) :: 2002 - Heater Blowing Out Cold Air
After changing my CD player, my heater blows out cold air (not icy cold but cold like you have put the thermostat on low heat) all the time but my temperature gauge is perfectly normal! Its right in between cold and hot.
View 3 RepliesAccent LC (2000-05) :: 2004 - Key Stuck In Lock Position In Ignition / Wheel Locked
My 2004 Accent is stuck in the "lock" position in the ignition, and the wheel is locked and barely turns in either direction. I know this is supposed to be an anti-theft feature and I've tried all of the solutions listed here...
Turning the wheel hard and soft in either direction while holding the brake all the way down and trying to turn the key. Putting the car in neutral and then park and trying the above Disconnecting the battery for a few minutes and trying the above Jacking the car up on one side to release the tension on the pin.
My question is can I remove the spring at the bottom of the locking pin by drilling a hole in the center of the plate? I've seen a few youtube videos of this done on BMW's. It will cost me $500 minimum to replace the ignition or steering column based on quotes I got.
Accent LC (2000-05) :: Heater Fan Stay On With Key Removed And Battery Went Dead Flat
I've a Hyundai 03 Accent that wont turn over. The heater fan would stay on with the key removed and subsequently my battery went dead flat.
I tried to roll start, then jump start to no avail. I fully charged the battery overnight but now when starting the car there is no response. I checked the battery - 12.7 volts. Checked the fuse' under the hood, getting power there. Checked the power supply to the ignition switch - 12.7 volts.
There is no lights on the dash - i.e., engine check, airbag etc. But the interior overhead lights, door open and headlights all work fine.
Iv'e got a hold of an 00 accent running fine and have been swapping parts out. I swapped all the fuses I could see that might be causing the problem. Swapped ignition switch. Swapped fuses under the dash.
I have power to the ignition switch with the key out. Key in, no power to switch. On the running accent I have power to different wire depending on key location.
Passat (B5) :: AC / Heater Temp / Fans Knob Went Out
I have a 99 B5 and the lights for the Heater Temp Knob, the AC/ heater Fan Knob and the blower direction knob are all out. The fuses are OK. I have checked that.
View 2 RepliesAccent LC (2000-05) :: Heater / AC Blower Fan Starts Out Slow And Slowly Gains Speed
Sometimes it works sometimes it doesn't. It it the blower, the switch or the little box behind the blower? When it does work, it starts out slow and slowly gains speed.
View 1 Replies