Dodge - Intrepid :: 2000 - AC Clutch Always On Even In Heat Mode (no Defrost Mode)

I have a 2000 Intrepid with ATC (automatic temperature control).I noticed my A/C clutch is always is on even in heat mode (no defrost mode) Is this normal in automatic mode even if I set temp at 90° without defrost mode? Been looking on forums and some say it is normal for newer cars and some say no. What is correct.Doesn't seem normal to me when I set temp at 90° and the A/C is still running. The heat does work though.I did check for voltage at the clutch and it has power so something is telling it to run, (not a bad clutch,stuck clutch etc).

I never seen or heard it cycle when watching it. (hard to tell when driving) because the cooling fans go from low to high sometimes even without the A/C cycling.

In manual mode I can physically turn on or off the A/C but if it is on, I never seen it cycle yet when set at a normal temp 72-75° is this normal?I know it depends on outside temp,humidity, inside temp etc but if it feels comfortable in the cabin shouldn't the A/C cycle on and off every few minuts-10 minutes etc or is it normal to go 30 minutes or more without cycling? I don't have it on max Cool or recirculate mode either.

View 5 Replies

Ford F-150 (2009-2014) :: Check Engine Light And Limp Home Mode

Truck: 2009 F-150 Lariat SCrew 5.4 4x4 with 6.5" bed

For the last few years, I've had this intermittent problem where the service engine light (wrench icon) will pop on and the truck will go into limp home mode. While it's in this mode, all of the indicators on the dash freak out. Low fuel warning will come on, temperature warning, low battery voltage, etc. Turning the truck off and back on (sometimes a couple times) is enough to get it back to normal, albeit with a check engine light that needs to be cleared. It's happened infrequent enough that I've just been dealing with it. I got the codes a couple years back, but there wasn't much information available on what the potential causes might be. The Checker Auto parts database suggested one might be related to a wheel speed sensor.

Well, this afternoon it happened again, and I was near an O'Reilly, so I took it in to pull the codes. There were 9 total in the system; 5 of which were unique:

B0025
B00D5
U0073
U0100
U0253

They didn't have any information on what was causing them. What could be causing this. I'm getting sick of having to clear the check engine light and worry about the truck falling into limp home mode when I'm at intersections.

View 1 Replies

Santa FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On

2002 Santa Fe, 2.7 AWD

The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.

Fluid levels are fine.

With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.

View 2 Replies

Ford Super Duty (1999-2016) :: 2015 F250 - Check Engine Light Comes On And Truck Goes Into Limp Mode

Bought a brand new F250 6.7 it has 7000 miles in it now and the check engine light comes on and the truck goes into limp mode. I have taken it in to the dealership twice they said there is no code they can find and they just reset the check engine light and it does ok for a bit then starts the cycle all over again. It also is only getting about 6.5 mpg....

View 6 Replies

Ford Ranger / B-Series :: Transmission Goes Into Limp Mode When AC Turned On

Turn air conditioner on transmission goes into limp mode??

1999 ranger 2 door 2,5 engine long wheel base,,auto trans.

2wd no power windows no power seats....

View 12 Replies

Dodge - Stratus :: 1997 - Auto Trans Not Shifting / Total Limp Mode

I read another blog on here about stratus not shifting and decided to ask someone about my limp mode problem. A few months ago I was driving uphill when it jerked before it got into limp mode. I thought maybe the hot weather caused it(it was 95 deg). I let it sit overnight. and the next day car was fine. for about 3-4 months. Now it got into limp mode only after it goes through all the gears once only. When i come to a stop it will go into limp again. Got a 0700 and 0760 codes. My speedometer works. tach works. Basically everything works as it should.

I decided to change the ATF and filter, both speed sensors and i get the same old codes after a drive around the block. I then decided to remove the neg terminal overnight. Next day I would have no signal at the data link port. When i removed the key from the ignition my dash lights for the mileage will stay on for another 3-4 seconds before disappearing. I checked the ground wires to the PCM and TCM which are good. Fuses and relays are also good. I even swapped some of them. Still no change. 1997 stratus 2.4 auto...

View 4 Replies

Ford Super Duty (1999-2016) :: Transmission Would Not Work In Tow Mode And Caused Engine To Go Into Limp Mode

I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.

There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.

About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.

The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?

Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.

View 14 Replies

IS F (2008-2014) :: Check VSC Came On - Car Did Not Go Into Limp Mode And Operate Normal

As I pulled into a parking lot last night, my "check VSC" warning message came on. Simultaneously, the Parking Brake light, ABS light, Traction Control, and VSC lights came on. The car did not go into limp mode though, and the car seems to operate as normal (even when going WOT).

View 14 Replies

Golf IV / Jetta IV :: 2003 Goes Into Limp Mode With AC On?

03 manual goes into limp mode with ac on like turbo has no power and wont go past 65. No engine light comes on though. Does engine light have to come on to go into limp mode??

I don't have Vag Com. But i'm familiar with diesels. Maybe something is losing vacuum when a/c comes on because i know the ducts and all that work off vacuum in most cars. Does the ducts for TDi work off vacuum also??? Maybe not enough vacuum going to VNT activator?? I'm clueless with these cars.

View 3 Replies

Dodge - Intrepid :: 1999 - Engine Keeps Turning Off While Driving

I have been to several mechanics, no one can find anything wrong with it. This 1999 dodge intrepid only has 75,000 miles on it. While driving the engine turns off and will not turn back on for 30 minutes to hours. it does not happen all the time. The mechanic said there is nothing wrong with the car, and as soon as i went to pick it up driving it back home it turned off again?

View 3 Replies

Passat (B6) :: EPC Light Came On - Engine Went To Limp Mode

Passat 2008/09 TSI engine 16k miles. APR stage 2+

I was driving normally and suddenly EPC light comes on, and the engine goes to limp mode. I turn the engine off and then turn on again. Everything runs fine. Vag shows N276 intermittent fail. I had already this fail, but always when starting engine, and the engine used to run OK. Is this a "sign" that is time to replace the HPFP? Or can I take the chance and keep running?

View 3 Replies

Starting - Dodge - Intrepid :: Engine Sludge / Car Wouldn't Start Without Being Jumped Off

We have a poorly maintained 2001 Dodge Intrepid 2.7L with 155,000 miles on it. Over the Christmas break, we left it untouched in the driveway for a month. After that it wouldn't start without being jumped off, and the oil light flickered when the car idled. We had the battery, alternator, and starter checked at a local shop; all of them checked out fine. Nevertheless, the car wouldn't start without being jumped off. It would click once, and then nothing. We also noticed it was overdue by 2,000 miles for an oil change, and thought this may be causing the oil light issue. Since the 2.7L Intrepids are notorious for engine sludge, we added a couple of ounces of Seafoam, drove about 15 miles, and then took it in for an oil change. Now it starts without a jump. So my question is Is there any way that oil sludge (and perhaps a weak starter?) is the issue?

View 6 Replies

Santa FE SM (2001-06) :: P0335 And P1372 - Engine Goes Into Limp Mode And Very Hard To Start

I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.

So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.

I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.

The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/

View 16 Replies

Ford F-150 - 1997-2003 :: Overheating / Temp Gauge Climbs And Then Truck Goes Into Limp Mode

I am looking at a 1997 F150 with a 5.4 in it, guy who owns it says if you drive it down the street the temp gauge climbs and then the truck goes into limp mode but if you check the engine temp under hood it is nowhere near overheating. Where I should start to look for a problem here? If this is too complicated I will pass on the truck, its not worth it to me to get this truck if it is going to be a nightmare. I have a 2000 with a 4.6 that runs great so this would just be a spare for me, but would like to have it because its in such nice shape.

View 1 Replies

Intrepid :: Check Engine Light Came On - Transmission Code P0731

My wifes 1998 Intrepids' Check Engine Light came on yesterday, and while she was turning into the driveway the car stalled. It would fire right up again, and drive normally, but when she went to pull into the driveway again it stalled.

I took it into the shop, and they read the computer and thats when the P0731 code showed up.

P0731 Incorrect gear ratio # 1

When I went to bring it home, I then noticed that the speedometer was not working, and the tranny wasn't shifting out of 1st gear. The tranny fluid is clean and not burnt.

View 1 Replies

Ford Super Duty (1999-2016) :: 2008 F350 Going In Limp Mode Without Engine Light - Code P0088

Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.

Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.

View 3 Replies

Prius (2004-09) :: Check Engine Light Turned On For A Few Hours Then Turned Off

I always take care of my car oil changes on time. And in the last week my check engine light turned on for a few hours then turned off. And today it turned on again. I kinda regret getting rid of my scan gauge now.

View 11 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Check Engine Light Not Coming On When Ignition Turned On?

2002 F350 7.3 PSD. 192k miles.

From my understanding, a CEL is supposed to illuminate each time you turn the ignition ON as part of normal startup procedure.

I figured the previous owner must have pulled out the bulb to hide the fact that the truck had a few "issues" before selling it, so today I pulled out the gauge cluster and it looked as if the CEL bulb was a tiny LED soldered directly into the gauge cluster itself. There were a few serviceable/removable bulbs for things like turn signal indicators, high-beam etc... but the CEL did not have a serviceable/removable bulb.

I've been driving this truck and working through it's "issues" and fixing things as I go, but it keeps throwing codes without the CEL illuminating. What's going on here?

I thought the check-engine-light was supposed to illuminate each time the ignition was turned on, and that it would come on each and every time the vehicle registered a fault code in the ECU/PCM.

View 14 Replies

Intrepid :: 2003 To 2000 Engine Change?

I found a low mileage 2000 intrepid with the 2.7 liter engine from a car that was in a wreck. I would like to put this in my 2003 intrepid with a dead 2.7. Someone said that 99-01 engines can be interchanged easily but I have a 2000. The first thing I noticed is that the engine harnesses are different between the cars, so I was wondering if I change the out the harness with my 2003 harness, next I trashed my flex plate so can I use flex plate and torque converter from the 2000. Would the engine still work?

View 2 Replies